DTC U0100-211 Lost Communication with ECM / PCM "A" |
DTC U0100-212 Lost Communication with ECM / PCM "A" |
DTC U0100-530 Lost Communication with ECM / PCM "A" |
DTC U0129-220 Lost Communication with Brake System Control Module |
DTC U0129-222 Lost Communication with Brake System Control Module |
DTC U0129-527 Lost Communication with Brake System Control Module |
DTC U0129-528 Lost Communication with Brake System Control Module |
DTC U0140-146 Communication Error from Body ECU to HV ECU |
DTC U0151-763 Communication Error from Airbag ECU to HV ECU |
DTC U0164-594 Communication Error from A/C ECU to HV ECU |
DTC U0164-827 Communication Error from A/C ECU to HV ECU |
DTC U1107-436 Lost Communication with Power Management Module |
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| U0100 | 211 | Problem with CAN communication between the ECM and power management control ECU (communication error between ECUs) (1 trip detection logic) | CAN communication system |
| U0100 | 212 | Problem with CAN communication between the ECM and power management control ECU (signal transmission error) (1 trip detection logic) | |
| U0100 | 530 | Problem with CAN communication between the ECM and power management control ECU (CAN communication system malfunction) (1 trip detection logic) | |
| U0129 | 220 | Problem with CAN communication between the skid control ECU assembly and power management control ECU (no signal reception) (1 trip detection logic) | |
| U0129 | 222 | Problem with CAN communication between the skid control ECU assembly and power management control ECU (signal transmission error) (1 trip detection logic) | |
| U0129 | 527 | Problem with CAN communication (V1 BUS) between the skid control ECU assembly and power management control ECU (CAN communication system malfunction) (1 trip detection logic) | |
| U0129 | 528 | Problem with CAN communication between the skid control ECU assembly and power management control ECU (CAN communication system malfunction) (1 trip detection logic) | |
| U0140 | 146 | Problem with CAN communication between the main body ECU and power management control ECU (CAN communication system malfunction) (1 trip detection logic) | |
| U0151 | 763 | Problem with CAN communication between airbag sensor assembly and power management control ECU (CAN communication system malfunction) (1 trip detection logic) | |
| U0164 | 594 | Problem with CAN communication between the air conditioning amplifier assembly and power management control ECU (communication error between ECUs) (1 trip detection logic) | |
| U0164 | 827 | Problem with CAN communication between air conditioning amplifier assembly and power management control ECU (CAN communication system malfunction) (1 trip detection logic) | |
| U1107 | 436 | Problem with CAN communication between the power source ECU and power management control ECU (CAN communication system malfunction) (1 trip detection logic) |
| Related DTCs | U0100 (INF 211/212/530): Performance |
| Required sensors / components | Main: Power management control ECU (HV CPU) Sub: CAN bus line |
| Frequency of operation | Continuous |
| Duration | TMC's intellectual property |
| MIL operation | Immediately |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not present | TMC's intellectual property |
| Other conditions belong to TMC's intellectual property | - |
| TMC's intellectual property | - |
| Power management control ECU (HV CPU) | DTC U0100 (INF 211/212/530) is not detected |

| 1.CHECK DTC OUTPUT (ALL) |
Connect the Techstream to the DLC3.
Turn the power switch on (IG).
Check for DTCs of all systems by following the prompts on the Techstream screen.
Check if DTCs are output.
| Result | Proceed to |
| Power management control ECU outputs P2532-772 | A |
| Power management control ECU does not output P2532-772 | B |
Turn the power switch off.
|
| ||||
| A | ||
| ||