Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS

WINDSHIELD GLASS > REMOVAL

for Preparation Click here



1. REMOVE ROOF HEADLINING ASSEMBLY
(Click here)


2. REMOVE WINDSHIELD GLASS SUB-ASSEMBLY


    B296182E01
  1. Apply protective tape to the area around the installation position of the windshield glass on the vehicle body to prevent it from being scratched.
    Text in Illustration 
    *1
    Protective Tape



    B296204E01
  1. Using a knife, cut off the moulding as shown in the illustration.
    Text in Illustration 
    *1
    Windshield Glass
    *2
    Moulding
    *3
    Body



    B296183E01
  1. Place matchmarks on the windshield glass sub-assembly and vehicle body on the locations indicated in the illustration.
    Text in Illustration 
    *1
    Matchmark

    HINT:
    Matchmarks are not necessary if the windshield glass sub-assembly is not going to be reused.



    B296185E01
  1. Pass a piano wire between the vehicle body and glass from the interior.
    Text in Illustration 
    *1
    Windshield Glass Stopper
    *2
    Piano Wire

  1. Tie both wire ends to wooden blocks or similar objects that can serve as handles.

  1. Cut off the adhesive by pulling the piano wire around the windshield glass sub-assembly.

    NOTICE:
    1. When separating the windshield glass sub-assembly, be careful not to damage the paint or interior and exterior ornaments.
    2. To prevent the safety pad from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and safety pad.



  1. Disconnect the windshield glass stoppers.


    B296186E01


    Text in Illustration 
    *A
    1-piece Type
    *B
    2-pieceType
    *1
    No. 1 Windshield Glass Stopper
    *2
    No. 2 Windshield Glass Stopper

    NOTICE:
    1. There are No. 1 and No. 2 stoppers on the windshield glass as shown in the illustration. Be careful not to damage the windshield glass when cutting off the adhesive.
    2. To prevent the windshield glass from falling when performing this operation, be sure to hold the windshield glass using suction cups.

    HINT:
    Depending on the vehicle, either 1-piece or 2-piece type stoppers may be present.

  1. Using suction cups, remove the windshield glass sub-assembly.

    NOTICE:
    1. Be careful not to drop the windshield glass sub-assembly.
    2. Leave as much adhesive on the vehicle body as possible when removing the windshield glass sub-assembly.



3. REMOVE WINDOW GLASS ADHESIVE DAM


  1. When reusing the windshield glass:



      B296187E01
    1. Using a scraper, remove the window glass adhesive dam.
      Text in Illustration 
      *A
      Back Side

      NOTICE:
      1. Be careful not to damage the windshield glass.
      2. Be sure to replace the window glass adhesive dam with a new one.



4. REMOVE WINDSHIELD OUTSIDE MOULDING


  1. When reusing the windshield glass:



      B296188E01
    1. Using a scraper, remove the windshield outside moulding.
      Text in Illustration 
      *A
      Back Side

      NOTICE:
      1. Be careful not to damage the windshield glass.
      2. Be sure to replace the windshield outside moulding with a new one.



5. REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 1-piece Type)


  1. When reusing the windshield glass:



      B296189E01
    1. Using a scraper, remove the 2 No. 1 windshield glass stoppers.
      Text in Illustration 
      *A
      Back Side

      NOTICE:
      1. Be careful not to damage the windshield glass.
      2. Be sure to replace the 1-piece type No. 1 windshield glass stoppers with a new pair of 2-piece type No. 1 and No. 2 windshield glass stoppers.



6. REMOVE NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)


  1. When reusing the windshield glass:



      B296189E01
    1. Using a scraper, remove the 2 No. 2 windshield glass stoppers.
      Text in Illustration 
      *A
      Back Side

      NOTICE:
      1. Be careful not to damage the windshield glass.
      2. Be sure to replace the No. 2 windshield glass stoppers with new ones.



7. REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)


    B296190
  1. Remove the 2 No. 1 windshield glass stoppers.

    NOTICE:
    Be sure to replace the No. 1 windshield glass stoppers with new ones.



8. CLEAN WINDSHIELD GLASS


  1. When reusing the windshield glass:



      B149736
    1. Using a scraper, remove any adhesive dam and adhesive residue from the windshield glass.

      NOTICE:
      Be careful not to damage the windshield glass.

    2. Clean the outer circumference of the windshield glass with a non-residue solvent.

      NOTICE:
      1. Do not touch the windshield glass surface after cleaning it.
      2. Even if using a new windshield glass, clean the windshield glass with a non-residue solvent.



9. CLEAN VEHICLE BODY


    B296195E01
  1. Clean and shape the contact surfaces of the vehicle body.
    Text in Illustration 
    *1
    Body
    *2
    Adhesive

    1. Using a knife, cut away excess adhesive on the contact surfaces of the vehicle body as shown in the illustration.

      NOTICE:
      Be careful not to damage the vehicle body.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

    2. Clean the contact surfaces of the vehicle body with a piece of cloth saturated with cleaner.

      HINT:
      Even if all the adhesive has been removed, clean the vehicle body.