BACK DOOR GLASS > INSTALLATION |
| 1. INSTALL BACK WINDOW GLASS CLIP LH |
Using a brush or sponge, coat the application area of new back window glass clip LH with primer G.
![]() |
Install a new back window glass clip LH onto the back door glass as shown in the illustration.
| *A | Back Side |
| *1 | Ceramic Notch |
| 2. INSTALL BACK WINDOW GLASS CLIP RH |
Using a brush or sponge, coat the application area of new back window glass clip RH with primer G.
![]() |
Install a new back window glass clip RH onto the back door glass as shown in the illustration.
| *A | Back Side |
| *1 | Ceramic Notch |
| 3. INSTALL BACK WINDOW GLASS ADHESIVE DAM |
Using a brush or sponge, coat the application area of a new back window glass adhesive dam with primer G.
![]() |
Cut a new back window glass adhesive dam (a) so that it fits to the position specified in the illustration.
| *A | Back Side |
| *1 | Ceramic Notch for Dam Alignment |
| Area | Dimension |
| a | 1053 mm (3.45384 ft.) |
| b | 3.0 mm (0.118 in.) |
Install a new back window glass adhesive dam onto the back door glass as shown in the illustration.
![]() |
Cut a new back window glass adhesive dam (a) so that it fits to the position specified in the illustration.
| *A | Back Side |
| *1 | Ceramic Notch for Dam Alignment |
| Area | Dimension |
| a | 1070 mm (3.5096 ft.) |
| b | 13.2 mm (0.52 in.) |
Install a new back window glass adhesive dam onto the back door glass as shown in the illustration.
| 4. INSTALL BACK DOOR GLASS SUB-ASSEMBLY |
![]() |
Position the back door glass sub-assembly.
| *1 | Matchmark |
Using suction cups, place the back door glass sub-assembly in the correct position.
Check that the whole contact surface of the back door glass rim is perfectly even.
Align the matchmarks on the back door glass and vehicle body.
Remove the back door glass.
Using a brush, coat the installation surface on the vehicle body with primer M.

| *1 | Brush | *2 | Primer M |
| *3 | Adhesive | - | - |
| *a | CORRECT | *b | INCORRECT |
| *c | Edge of Curved Surface | - | - |
Using a brush or sponge, coat the adhesive application area with primer G.

| *A | Back Side | - | - |
| *1 | Primer G | - | - |
| Area | Dimension |
| a | 9.0 mm (0.354 in.) or more |
| b | 22.0 mm (0.866 in.) or more |
| c | 23.9 mm (0.941 in.) or more |
| d | 16.0 mm (0.63 in.) or more |
Apply adhesive to the glass.
![]() |
Cut off the tip of the cartridge nozzle as shown in the illustration.
| *1 | Nozzle |
| Area | Dimension |
| a | 12.0 mm (0.472 in.) |
| b | 8.0 mm (0.315 in.) |
| Temperature | Usage Time Frame |
| 35°C (95°F) | 15 minutes |
| 20°C (68°F) | 1 hour and 40 minutes |
| 5°C (41°F) | 8 hours |
Load the sealer gun with the cartridge.
Apply adhesive to the back door glass as shown in the illustration.

| *A | Back Side | - | - |
| *1 | Adhesive | - | - |
| Area | Dimension |
| a | 5.0 mm (0.197 in.) |
| b | 8.0 mm (0.315 in.) |
| c | 26.9 mm (1.06 in.) |
| d | 5.0 mm (0.197 in.) |
Install the back door glass sub-assembly.
![]() |
Using suction cups, position the back door glass so that the matchmarks are aligned, and press it in gently along the rim.
| *1 | Matchmark |
Lightly press the front surface of the back door glass to ensure a close fit.
Using a scraper, remove any excess or protruding adhesive.
Hold the back door glass using protective tape until the applied adhesive becomes hard.
| Temperature | Minimum Time Prior to Driving Vehicle |
| 35°C (95°F) | 1 hour and 30 minutes |
| 20°C (68°F) | 5 hours |
| 5°C (41°F) | 24 hours |
Connect each connector.
| 5. INSPECT FOR LEAKS AND REPAIR |
After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
If water leaks into the cabin, allow the water to dry and add adhesive.
Remove the protective tape.
| 6. INSTALL REAR SPOILER ASSEMBLY |
| 7. INSTALL BACK DOOR TRIM COVER |
![]() |
Engage the 5 clips to install the back door trim cover.
| 8. INSTALL BACK DOOR TRIM BOARD ASSEMBLY |
![]() |
Install the back door trim board assembly with the 10 clips.