CRUISE CONTROL SYSTEM > Cruise Control Switch Circuit |

| 1.READ VALUE ON INTELLIGENT TESTER |
![]() |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Select the following menu items: Powertrain / Cruise Control / Data List.
Check the Data List to confirm proper functioning of the cruise control switch.
| *a | ON-OFF |
| *b | -/SET |
| *c | +/RES |
| *d | CANCEL |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Main SW M-CPU | Cruise control switch signal (Main CPU) / ON or OFF | ON: Cruise control switch (ON-OFF button) pushed OFF: Cruise control switch (ON-OFF button) released | - |
| Cancel Switch | CANCEL switch signal / ON or OFF | ON: CANCEL switch on OFF: CANCEL switch off | - |
| SET/COAST Switch | -/SET switch signal / ON or OFF | ON: -/SET switch on OFF: -/SET switch off | - |
| RES/ACC Switch | +/RES switch signal / ON or OFF | ON: +/RES switch on OFF: +/RES switch off | - |
| Main SW S-CPU | Cruise control switch signal (Sub CPU) / ON or OFF | ON: Cruise control switch (ON-OFF button) pushed OFF: Cruise control switch (ON-OFF button) released | - |
|
| ||||
| OK | ||
| ||
| 2.INSPECT CRUISE CONTROL SWITCH |
Remove the cruise control switch (Click here).
Measure the resistance according to the value(s) in the table below.

| *1 | Cruise Control Switch (ON-OFF button) | - | - |
| *a | Component without harness connected (Cruise Control Switch) | *b | ON-OFF |
| *c | +/RES | *d | -/SET |
| *e | CANCEL | - | - |
| Tester Connection | Switch Condition | Specified Condition |
| 1 - 3 | Cruise control switch (ON-OFF button) released | 1 MΩ or higher |
| Cruise control switch (ON-OFF button) pushed | Below 2.5 Ω | |
| +/RES | 235 to 245 Ω | |
| -/SET | 617 to 643 Ω | |
| CANCEL | 1509 to 1571 Ω |
|
| ||||
| OK | |
| 3.CHECK CRUISE CONTROL SWITCH WIRE (SPIRAL CABLE SUB-ASSEMBLY - CRUISE CONTROL SWITCH) |
![]() |
Disconnect the spiral with sensor cable sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| z6-3 - 3 | Below 1 Ω |
| z6-4 - 1 | Below 1 Ω |
| *a | Front view of wire harness connector (to Spiral with Sensor Cable Sub-assembly) |
| *b | Front view of wire harness connector (to Cruise Control Switch) |
|
| ||||
| OK | |
| 4.CHECK SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY |
![]() |
Remove the spiral with sensor cable sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z6-3 - G5-1 (CCS) | Center | Below 3 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| z6-4 - G5-2 (ECC) | Center | Below 3 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right |
After setting the spiral with sensor cable sub-assembly to the center position, rotate the spiral with sensor cable sub-assembly 2.5 times clockwise. Then while rotating the spiral with sensor cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z6-3 - G5-1 (CCS) | Always | Below 3 Ω |
| z6-4 - G5-2 (ECC) | Always | Below 3 Ω |
| *a | Component without harness connected (Spiral with Sensor Cable Sub-assembly) |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - SPIRAL CABLE SUB-ASSEMBLY) |
Disconnect the power management control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G5-1 (CCS) - G58-22 (CCS) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| G5-1 (CCS) or G58-22 (CCS) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND) |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G5-2 (ECC) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Spiral with Sensor Cable Sub-assembly) |
|
| ||||
| OK | ||
| ||