Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B1442/42    Air Inlet Damper Control Servo Motor Circuit

for Preparation Click here


DESCRIPTION

The No. 1 blower damper servo sub-assembly (air inlet) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal, reverse) based on the signals to move the air inlet mode selection No. 1 blower damper servo sub-assembly (air inlet) to any position, which controls the intake air settings (FRESH, FRESH/RECIRCULATION, and RECIRCULATION).
The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.

HINT:
Confirm that no mechanical problem is present because this diagnostic code can be stored when either a damper link or the damper is mechanically locked.


DTC No.
DTC Detection Condition
Trouble Area
B1442/42
Air inlet damper position sensor value does not change even though air conditioning amplifier assembly operates No. 1 blower damper servo sub-assembly (air inlet).
  1. No. 1 blower damper servo sub-assembly (air inlet)
  2. Air conditioning harness assembly
  3. Air conditioning amplifier assembly

WIRING DIAGRAM


E229253E02


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Operate the R/F (Recirculation/Fresh) switch.

  1. Enter the following menus: Body / Air Conditioner / Data List.

  1. Check the value(s) by referring to the table below.


Air Conditioner 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Air Inlet Damper Actual Pulse
No. 1 blower damper servo sub-assembly (air inlet) actual pulse / Min.: 128, Max.: 383
RECIRCULATION: 287 (pulse)
FRESH: 254 (pulse)
-

OK:
The display is as specified in the normal condition column.


Result:

Result
Proceed to
NG
A
OK (When troubleshooting according to Problem Symptoms Table)
B
OK (When troubleshooting according to the DTC)
C



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
A


2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Air Conditioner / Active Test.

  1. Check the operation by referring to the table below.


Air Conditioner 
Tester Display
Test Part
Control Range
Diagnostic Note
Air Inlet Damper Targ Pulse
No. 1 blower damper servo sub-assembly (air inlet) pulse
Min.: 128, Max.: 383
Operates between 254 and 287 pulses

OK:
Recirculation damper position changes in accordance with each control range.



NG
Go to step 3
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

3.REPLACE NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY (AIR INLET)
  1. Replace the No. 1 blower damper servo sub-assembly (air inlet) (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1442/42 is output
    A
    DTC B1442/42 is not output
    B



B
END (NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY (AIR INLET) WAS DEFECTIVE)
A


4.REPLACE AIR CONDITIONING HARNESS ASSEMBLY
  1. Replace the air conditioning harness assembly (Click here).

    HINT:
    Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1442/42 is output
    A
    DTC B1442/42 is not output
    B



B
END (AIR CONDITIONING HARNESS ASSEMBLY WAS DEFECTIVE)
A

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)