Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT

AIR CONDITIONING UNIT > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
Make sure to select FACE mode before disconnecting the cable from the negative (-) auxiliary battery terminal.



2. RECOVER REFRIGERANT FROM AIR CONDITIONING SYSTEM
  1. Start the hybrid system.

  1. Operate the cooler compressor under the conditions show below:
    Item
    Condition
    Engine Speed
    Idling
    Operating Time
    3 minutes or more
    A/C Switch Status
    ON
    Blower Switch Status
    HI
    Set Temperature
    MAX COOL
    This causes most of the compressor oil from the various components of the A/C system to collect in the A/C compressor.

    HINT:
    It is not necessary to operate the cooler compressor if the A/C does not operate because of compressor lock, etc.

  1. Stop the engine.

  1. Recover the refrigerant from the A/C system using a refrigerant recovery unit.

    HINT:
    Use the refrigerant recovery unit in accordance with the manufacturer's instruction manual.



3. REMOVE WINDSHIELD WIPER MOTOR AND LINK
(Click here)


4. REMOVE INNER COWL TOP TO COWL BRACE (for LHD)


    C250011
  1. Remove the 3 bolts and inner cowl top to cowl brace.



5. REMOVE INNER COWL TOP TO COWL BRACE (for RHD)


    C249834
  1. Remove the 3 bolts and inner cowl top to cowl brace.



6. REMOVE FRONT AIR SHUTTER SEAL (for LHD)


    C250012
  1. Disengage the clamp to remove the front air shutter seal.



7. REMOVE FRONT AIR SHUTTER SEAL (for RHD)


    C249836
  1. Disengage the clamp to remove the front air shutter seal.



8. REMOVE FRONT NO. 1 VENTILATOR SEAL (for LHD)


    C250013
  1. Disengage the clamp to remove the front No. 1 ventilator seal.



9. REMOVE FRONT NO. 1 VENTILATOR SEAL (for RHD)


    C249835
  1. Disengage the clamp to remove the front No. 1 ventilator seal.



10. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)


    C250014
  1. Disengage the clamp to separate the wire harness from the outer cowl top panel sub-assembly.



    C250015
  1. Remove the 8 bolts, nut and outer cowl top panel sub-assembly.



11. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)


    C256179
  1. Disengage the 3 clamps to separate the wire harness from the outer cowl top panel sub-assembly.



    C249838
  1. Remove the 8 bolts, nut and outer cowl top panel sub-assembly.



12. DISCONNECT SUCTION PIPE SUB-ASSEMBLY


    E234992
  1. Remove the bolt and rotate the hook connector.



    E234993
  1. Disconnect the suction pipe sub-assembly.

  1. Remove the O-ring from the suction pipe sub-assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.



13. DISCONNECT LIQUID PIPE SUB-ASSEMBLY


    E234994
  1. Disconnect the liquid pipe sub-assembly.

  1. Remove the O-ring from the liquid pipe sub-assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.



14. DISCONNECT HEATER WATER OUTLET HOSE A


    E234995
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water outlet hose A.

    NOTICE:
    1. Do not apply excessive force to the heater outlet water hose A.
    2. Prepare a drain pan or cloth in case the coolant leaks.



15. DISCONNECT WATER HOSE SUB-ASSEMBLY


    E234996
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the water hose sub-assembly.

    NOTICE:
    1. Do not apply excessive force to the water hose sub-assembly.
    2. Prepare a drain pan or cloth in case the coolant leaks.



16. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
(Click here)


17. REMOVE STEERING COLUMN ASSEMBLY
(Click here)


18. REMOVE POWER MANAGEMENT CONTROL ECU


    E245183E01
  1. Disconnect the 4 connectors.
    Text in Illustration 
    *A
    for LHD:
    *B
    for RHD:



    E245184E01
  1. Remove the 2 nuts and power management control ECU.
    Text in Illustration 
    *A
    for LHD:
    *B
    for RHD:



19. DISCONNECT INSTRUMENT PANEL WIRE


  1. Remove the bolt.


    E245181E01


    Text in Illustration 
    *A
    for LHD:
    *B
    for RHD:

  1. Disengage the 2 clamps and disconnect the instrument panel wire.



20. REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (for LHD)


    E240403E01
  1. Disengage the clamp.

  1. Disconnect the connector (A).

  1. Disengage the 2 claws and disconnect the 2 connectors (B).



    E240404
  1. Remove the 2 bolts.

  1. Disengage the 2 clamps and pull out the instrument panel junction block assembly.



    E240395
  1. Disengage the claw and disconnect the connector as shown in the illustration.



    E240397
  1. Disengage the claw and release the connector lock as shown in the illustration.



    E240399
  1. Disengage the claw and disconnect the connector as shown in the illustration to remove the instrument panel junction block assembly.



21. REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (for RHD)


  1. for Halogen Headlight:



      E234299E01
    1. Disconnect the 2 connectors (A).
      Text in Illustration 
      *A
      for Halogen Headlight:
      *B
      for LED Headlight:

  1. for LED Headlight:

    1. Disconnect the 3 connectors (A).

  1. Disengage the 2 claws and disconnect the 2 connectors (B).

  1. Disengage the clamp.



    E234298
  1. Remove the 2 bolts.

  1. Disengage the 2 clamps and pull out the instrument panel junction block assembly.



    E237596
  1. Disengage the claw and disconnect the connector as shown in the illustration.



    E237598
  1. Disengage the claw and release the connector lock as shown in the illustration.



    E237600
  1. Disengage the claw and disconnect the connector as shown in the illustration to remove the instrument panel junction block assembly.



22. REMOVE POWER STEERING ECU ASSEMBLY (for LHD)


    C248048
  1. Disconnect the 4 connectors from the power steering ECU assembly.



    C248049
  1. Remove the 2 nuts and power steering ECU assembly.



23. REMOVE POWER STEERING ECU ASSEMBLY (for RHD)


    C249576
  1. Disconnect the 4 connectors from the power steering ECU assembly.



    C249577
  1. Remove the 2 nuts and power steering ECU assembly.



24. REMOVE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY


    B300435
  1. Disconnect the connector.

  1. Disengage the clamp and remove the No. 1 indoor electrical key antenna assembly.

    NOTICE:
    Be careful when removing the indoor electrical key antenna assembly. If the antenna is dropped, replace it with a new one.



25. REMOVE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY


    B300439
  1. Disconnect the connector.

  1. Disengage the clamp and remove the No. 2 indoor electrical key antenna assembly.

    NOTICE:
    Be careful when removing the indoor electrical key antenna assembly. If the antenna is dropped, replace it with a new one.



26. DISCONNECT FRONT FLOOR CARPET ASSEMBLY
  1. Turn back the front floor carpet assembly.



27. REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY (for LHD)


    E249366E01
  1. Disengage each clamp.
    Text in Illustration 
    *1
    Bolt
    *2
    Screw
    *3
    Nut

  1. Remove the 2 bolts, screw, nut and No. 1 instrument panel brace sub-assembly.



28. REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY (for RHD)


    E245864E01
  1. Disengage each clamp.
    Text in Illustration 
    *1
    Bolt
    *2
    Screw
    *3
    Nut

  1. Remove the bolt, screw, nut and No. 1 instrument panel brace sub-assembly.



29. DISCONNECT INSTRUMENT PANEL WIRE (for LHD)


    E238210
  1. for LH Side:

    1. Disconnect each connector.



    2. E238209
    3. Disconnect the connector from the connector holder.

    4. Remove the bolt.

    5. Disengage each clamp and disconnect the connector holder.



    E238208
  1. for RH Side:

    1. Disconnect each connector.



    2. E238211
    3. Remove the bolt.

    4. Disengage each clamp and disconnect the connector holder.



  1. Remove the 2 bolts <A> and disconnect the 2 earth wires.


    E249751E01


    Text in Illustration 
    *1
    Earth Wire
    *2
    Bolt <A>
    *3
    Bolt <B>
    -
    -

  1. Remove the bolt <B>.

  1. Disconnect the connector.

  1. Disengage each clamp.



  1. Remove the bolt and disconnect the earth wire.


    E249752E01


    Text in Illustration 
    *1
    Earth Wire
    -
    -

  1. Disconnect the connector.

  1. Disengage each clamp and disconnect the instrument panel wire.



30. DISCONNECT INSTRUMENT PANEL WIRE (for RHD)


    E235011
  1. for RH Side:

    1. Disconnect each connector.



    2. E235012
    3. Disconnect the connector from the connector holder.

    4. Remove the bolt.

    5. Disengage each clamp and disconnect the connector holder.



    E235013
  1. for LH Side:

    1. Disconnect each connector.



    2. E235014
    3. Remove the bolt.

    4. Disengage each clamp and disconnect the connector holder.



  1. Remove the 2 bolts and disconnect the 2 earth wires.


    E249746E01


    Text in Illustration 
    *1
    Earth Wire
    -
    -

  1. Disconnect each connector.

  1. Disengage each clamp.



  1. Remove the bolt <A> and disconnect the earth wire.


    E249747E01


    Text in Illustration 
    *1
    Earth Wire
    *2
    Bolt <A>
    *3
    Bolt <B>
    -
    -

  1. Remove the bolt <B>.

  1. Disconnect the connector.

  1. Disengage each clamp and disconnect the instrument panel wire.



31. REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY


  1. Remove the 8 bolts and 3 screws, and remove the instrument panel reinforcement.


    E249753E01


    Text in Illustration 
    *1
    Bolt
    *2
    Screw



32. REMOVE DEFROSTER NOZZLE ASSEMBLY


    E238215
  1. Disengage the 2 claws and 3 guides and remove the defroster nozzle assembly.



33. DISCONNECT DRAIN COOLER HOSE


    E238216
  1. Disconnect the drain cooler hose.



34. REMOVE AIR CONDITIONER UNIT ASSEMBLY


  1. Remove the 3 bolts and nut, and remove the air conditioner unit assembly.


    E249223



35. REMOVE AIR CONDITIONING RADIATOR ASSEMBLY (for LHD)


  1. Disconnect the connector.


    E238218

  1. Remove the 3 screws and air conditioning radiator assembly.



36. REMOVE AIR CONDITIONING RADIATOR ASSEMBLY (for RHD)


  1. Disconnect the connector.


    E249224

  1. Remove the 3 screws and air conditioning radiator assembly.



37. REMOVE ASPIRATOR


    E238219
  1. Disengage the 2 claws and remove the aspirator.



38. REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY


    E238220
  1. Disconnect the connector.

  1. Remove the screw.



  1. Remove the air conditioning amplifier assembly as shown in the illustration.


    E238221



39. REMOVE AIR CONDITIONING HARNESS ASSEMBLY (for LHD)


  1. Disengage each clamp.


    E238224

  1. Disconnect each connector and remove the air conditioning harness assembly.



40. REMOVE AIR CONDITIONING HARNESS ASSEMBLY (for RHD)


  1. Disengage each clamp.


    E235028

  1. Disconnect each connector and remove the air conditioning harness assembly.



41. REMOVE NO. 3 AIR DUCT SUB-ASSEMBLY


    E238223
  1. Disengage the 3 claws and remove the No. 3 air duct sub-assembly.

    NOTICE:
    If any of the claws of the No. 3 air duct subassembly have been cracked or deformed during removal, make sure to replace the air duct with a new one. Failure to do so may cause the No. 3 air duct sub-assembly to fall off or noise to occur.



42. REMOVE NO. 2 AIR DUCT SUB-ASSEMBLY


    E238222
  1. Disengage the 3 claws and remove the No. 2 air duct sub-assembly.

    NOTICE:
    If any of the claws of the No. 2 air duct subassembly have been cracked or deformed during removal, make sure to replace the air duct with a new one. Failure to do so may cause the No. 3 air duct sub-assembly to fall off or noise to occur.