Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Check CAN Bus Line for Short to +B (RHD Models)

for Preparation Click here


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of the DLC3.

Symptom
Trouble Area
No resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of the DLC3.
  1. Short to +B in CAN main bus line
  2. Short to +B in CAN branch line
  3. ECM
  4. Brake booster with master cylinder assembly (Skid control ECU)
  5. Main body ECU (Multiplex network body ECU)
  6. Air conditioning amplifier assembly
  7. Power steering ECU assembly
  8. Smart key ECU assembly (Certification ECU)
  9. Airbag sensor assembly
  10. Spiral cable with sensor sub-assembly (Steering sensor)
  11. Hybrid vehicle control computer assembly
  12. Combination meter assembly
  13. CAN junction connector LH
  14. CAN junction connector RH

WIRING DIAGRAM


C260982E04


C251631E05


INSPECTION PROCEDURE

NOTICE:
  1. Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  2. After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).
  3. Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click here).
  4. After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
  5. DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control main switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more.
  6. After the repair, perform CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (Click here).

HINT:
  1. Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

1.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN J/C RH)
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



    C258680E10
  1. Disconnect the G72 CAN junction connector RH.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Connected to
    G72-1 (CANH) - G4-16 (BAT)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    Spiral cable with sensor sub-assembly (Steering sensor)
    G72-12 (CANL) - G4-16 (BAT)
    G72-4 (CANH) - G4-16 (BAT)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    Airbag sensor assembly
    G72-15 (CANL) - G4-16 (BAT)
    G72-6 (CANH) - G4-16 (BAT)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    Power steering ECU assembly
    G72-17 (CANL) - G4-16 (BAT)
    G72-7 (CANH) - G4-16 (BAT)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    Combination meter assembly
    G72-18 (CANL) - G4-16 (BAT)
    G72-8 (CANH) - G4-16 (BAT)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    Air conditioning amplifier assembly
    G72-19 (CANL) - G4-16 (BAT)
    G72-10 (CANH) - G4-16 (BAT)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    CAN junction connector LH
    G72-21 (CANL) - G4-16 (BAT)
    G72-11 (CANH) - G4-16 (BAT)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    DLC3
    G72-22 (CANL) - G4-16 (BAT)

    Text in Illustration 
    *1
    DLC3
    *a
    Front view of wire harness connector
    (to CAN Junction Connector RH)
    *b
    to Spiral Cable with Sensor Sub-assembly (Steering Sensor)
    *c
    to Airbag Sensor Assembly
    *d
    to Power Steering ECU Assembly
    *e
    to Combination Meter Assembly
    *f
    to Air Conditioning Amplifier Assembly
    *g
    to CAN Junction Connector LH
    *h
    to DLC3

Result:
Result
Proceed to
OK
A
NG (CAN junction connector LH main line)
B
NG (ECU or sensor bus line)
C
NG (DLC3 branch line)
D



B
Go to step 2

C
Go to step 4

D
REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3
A

REPLACE CAN JUNCTION CONNECTOR RH 

2.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN J/C LH (INSTRUMENT PANEL WIRE SIDE))


    C258680E21
  1. Disconnect the G71 CAN junction connector LH (instrument panel wire side).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Connected to
    G71-1 (CANH) - G4-16 (BAT)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    Main body ECU (Multiplex network body ECU)
    G71-12 (CANL) - G4-16 (BAT)
    G71-3 (CANH) - G4-16 (BAT)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    Smart key ECU assembly (Certification ECU)
    G71-14 (CANL) - G4-16 (BAT)
    G71-4 (CANH) - G4-16 (BAT)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    CAN junction connector RH
    G71-15 (CANL) - G4-16 (BAT)
    G71-5 (CANH) - G4-16 (BAT)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    Hybrid vehicle control computer assembly
    G71-16 (CANL) - G4-16 (BAT)

Text in Illustration 
*1
DLC3
*a
Front view of wire harness connector
(to CAN Junction Connector LH (Instrument Panel Wire Side))
*b
to Main Body ECU (Multiplex Network Body ECU)
*c
to Smart Key ECU Assembly (Certification ECU)
*d
to CAN Junction Connector RH
*e
to Hybrid Vehicle Control Computer Assembly

Result:
Result
Proceed to
OK
A
NG (CAN junction connector RH main line)
B
NG (ECU or sensor bus line)
C



B
REPAIR OR REPLACE CAN MAIN BUS LINE (CAN J/C LH (INSTRUMENT PANEL WIRE SIDE) - CAN J/C RH)

C
Go to step 4
A


3.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN J/C LH (ENGINE ROOM MAIN WIRE SIDE))


    C258680E05
  1. Disconnect the A51 CAN junction connector LH (engine room main wire side).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Connected to
    A51-9 (CANH) - G4-16 (BAT)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    ECM
    A51-20 (CANL) - G4-16 (BAT)
    A51-10 (CANH) - G4-16 (BAT)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    Brake booster with master cylinder assembly (Skid control ECU)
    A51-21 (CANL) - G4-16 (BAT)

Text in Illustration 
*1
DLC3
*a
Front view of wire harness connector
(to CAN Junction Connector LH (Engine Room Main Wire Side))
*b
to ECM
*c
to Brake Booster with Master Cylinder Assembly (Skid Control ECU)

Result:
Result
Proceed to
OK
A
NG (ECU or sensor bus line)
B



B
Go to step 4
A

REPLACE CAN JUNCTION CONNECTOR LH 

4.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU, SENSOR)
  1. Reconnect all wire harness connectors (CAN junction connector LH and CAN junction connector RH).

  1. Disconnect the ECU or sensor connected to the CAN bus line that is shorted to +B.

    HINT:
    If the ECU or sensor has multiple connectors, disconnect the connector that includes the CAN bus lines. To determine the ECU or sensor that is connected to the shorted bus line, refer to the terminals of ECU tables (Click here).



    C210421E71
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G4-6 (CANH) - G4-16 (BAT)
    Cable disconnected from negative (-) auxiliary battery terminal
    6 kΩ or higher
    G4-14 (CANL) - G4-16 (BAT)

    Text in Illustration 
    *1
    DLC3

    HINT:
    If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



NG
REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINE OR CONNECTOR
OK

REPLACE CORRESPONDING ECU OR SENSOR