Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Entry Function)

SMART ENTRY AND START SYSTEM (for Entry Function) > TERMINALS OF ECU

for Preparation Click here



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B264892E96

  1. Disconnect the G77 and G79 certification ECU (smart key ECU assembly) connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item
    G77-11 (E) - Body ground
    -
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    -
    G77-2 (+B) - G77-11 (E)
    Input
    B - W-B
    +B power supply
    Power switch off
    11 to 14 V
    -
    G77-10 (CUTB) - G77-11 (E)
    Input
    L - W-B
    Dark current cut pin*
    Power switch off
    11 to 14 V
    -
    1. *: In order to prevent the vehicle auxiliary battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is set in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle auxiliary battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode (example: the transmission of electric waves every 0.25 seconds. that form the detection area stops).
    If the result is not as specified, there may be a malfunction on the wire harness side or the fuse is removed.

  3. Reconnect the G77 and G79 certification ECU (smart key ECU assembly) connector.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item
    G79-5 (IG) - G77-11 (E)
    Input
    V - W-B
    IG power supply
    Power switch off → on (IG)
    Below 1 V → 11 to 14 V
    Engine Switch
    G79-12 (CLG1) - G77-11 (E)
    Output
    L - W-B
    Output to driver door electrical key antenna
    (request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Electrical key transmitter sub-assembly not inside vehicle
    5. Electrical key transmitter sub-assembly brought inside detection area*1
    6. All doors locked through wireless operation
    Pulse generation (See waveform 1)
    Over Head + Driver Side (key diagnostic mode)
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Electrical key transmitter sub-assembly not inside vehicle
    5. Electrical key transmitter sub-assembly brought outside detection area*2
    6. All doors locked through wireless operation
    Pulse generation (See waveform 2)
    Over Head + Driver Side (key diagnostic mode)
    G79-13 (CG1B) - G77-11 (E)
    Output
    P - W-B
    Output to driver door electrical key antenna (terminal on opposite side of component from CLG1 output terminal)
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Electrical key transmitter sub-assembly not inside vehicle
    5. Electrical key transmitter sub-assembly brought outside detection area*2
    6. All doors locked through wireless operation
    Pulse generation (See waveform 2)
    Over Head + Driver Side (key diagnostic mode)
    G79-11 (CLG2) - G77-11 (E)
    Output
    L - W-B
    Output to front passenger door electrical key antenna
    (request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Electrical key transmitter sub-assembly not inside vehicle
    5. Electrical key transmitter sub-assembly brought inside detection area*1
    6. All doors locked through wireless operation
    Pulse generation (See waveform 1)
    Over Head + Passenger Side (key diagnostic mode)
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Electrical key transmitter sub-assembly not inside vehicle
    5. Electrical key transmitter sub-assembly brought outside detection area*2
    6. All doors locked through wireless operation
    Pulse generation (See waveform 2)
    Over Head + Passenger Side (key diagnostic mode)
    G79-10 (CG2B) - G77-11 (E)
    Output
    P - W-B
    Output to front passenger door electrical key antenna (terminal on opposite side of component from CLG2 output terminal)
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Electrical key transmitter sub-assembly not inside vehicle
    5. Electrical key transmitter sub-assembly brought outside detection area*2
    6. All doors locked through wireless operation
    Pulse generation (See waveform 2)
    Over Head + Passenger Side (key diagnostic mode)
    G79-3 (CLG5) - G77-11 (E)
    Output
    P - W-B
    Output to No. 1 indoor electrical key antenna assembly (front floor)
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly not inside vehicle
    3. Door is open
    4. Door is closed
    5. Within 30 seconds
    Pulse generation (See waveform 3)
    Over Head + Front Room (key diagnostic mode)
    G79-2 (CG5B) - G77-11 (E)
    Output
    Y - W-B
    Output to No. 1 indoor electrical key antenna assembly (front floor) (terminal on opposite side of component from CLG5 output terminal)
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly not inside vehicle
    3. Door is open
    4. Door is closed
    5. Within 30 seconds
    Pulse generation (See waveform 3)
    Over Head + Front Room (key diagnostic mode)
    G79-20 (TSW1) - G77-11 (E)
    Input
    LG - W-B
    Driver door lock sensor signal input
    (Sends signal from door lock sensor on front door outside handle assembly to certification ECU (smart key ECU assembly). Certification ECU (smart key ECU assembly) send 12 V pulse waveform every 40 ms. from terminal TSW. When door lock sensor is touched, the pulse is grounded.
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Driver door lock sensor not touched → touched
    Pulse generation (See waveform 5)
    D-Door Trigger Switch
    G79-8 (TSW2) - G77-11 (E)
    Input
    LG - W-B
    Front passenger door lock sensor signal input
    (Sends signal from door lock sensor on front door outside handle assembly to certification ECU (smart key ECU assembly). Certification ECU (smart key ECU assembly) sends 12 V pulse waveform every 40 ms. from terminal TSW. When door lock sensor is touched, the pulse is grounded.
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Front passenger door lock sensor not touched → touched
    Pulse generation (See waveform 5)
    P-Door Trigger Switch
    G79-22 (SEN1) - G77-11 (E)
    Input
    BE - W-B
    Driver door unlock sensor signal input
    (when system is in unlock standby mode and touch sensor is touched, door electrical key antenna sends touch sensor input signal (sensing) to certification ECU (smart key ECU assembly))
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors locked
    4. Electrical key transmitter sub-assembly not sufficiently close to vehicle
    5. Driver door unlock sensor not touched → touched
    Pulse generation (See waveform 5)
    D-Door Touch Sensor
    G79-23 (SEN2) - G77-11 (E)
    Input
    R - W-B
    Front passenger door unlock sensor signal input
    (when system is in unlock standby mode and touch sensor is touched, door electrical key antenna sends touch sensor input signal (sensing) to certification ECU (smart key ECU assembly))
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors locked
    4. Electrical key transmitter sub-assembly not sufficiently close to vehicle
    5. Front passenger door unlock sensor not touched → touched
    Pulse generation (See waveform 5)
    P-Door Touch Sensor
    G78-27 (TSW5) - G77-11 (E)
    Input
    L - W-B
    Back door opener switch assembly (unlock switch) signal input
    Back door opener switch assembly (unlock switch) off → on
    Pulse generation (See waveform 5)
    Tr/B-Door Unlock SW
    G78-28 (TSW6) - G77-11 (E)
    Input
    G - W-B
    Back door opener switch assembly (lock switch) signal input
    Back door opener switch assembly (lock switch )off → on
    Pulse generation (See waveform 5)
    Tr/B-Door Lock SW
    G78-11 (CLG6) - G77-11 (E)
    Output
    LG - W-B
    Output to No. 2 indoor electrical key antenna assembly (steering column)
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly not inside vehicle
    3. Door is open
    4. Door is closed
    5. Within 30 seconds
    Pulse generation (See waveform 3)
    Over Head + Rear Room (key diagnostic mode)
    G78-10 (CG6B) - G77-11 (E)
    Output
    V*4 - W-B
    SB*5 - W-B
    Output to No. 2 indoor electrical key antenna assembly (steering column) (terminal on opposite side of component from CLG6 output terminal)
    Proceed:
    1. Power switch off
    2. Electrical key transmitter sub-assembly not inside vehicle
    3. Door is open
    4. Door is closed
    5. Within 30 seconds
    Pulse generation (See waveform 3)
    Over Head + Rear Room (key diagnostic mode)
    G78-9 (CLG7) - G77-11 (E)
    Output
    W - W-B
    Output to No. 3 indoor electrical key antenna assembly (rear floor)
    Proceed:
    1. Power switch off
    2. Electrical key transmitter sub-assembly not inside vehicle
    3. Door is open
    4. Door is closed
    5. Within 30 seconds
    Pulse generation (See waveform 3)
    Over Head + Back Door (inside) (key diagnostic mode)
    G78-8 (CG7B) - G77-11 (E)
    Output
    BR - W-B
    Output to No. 3 indoor electrical key antenna assembly (rear floor) (terminal on opposite side of component from CLG7 output terminal)
    Proceed:
    1. Power switch off
    2. Electrical key transmitter sub-assembly not inside vehicle
    3. Door is open
    4. Door is closed
    5. Within 30 seconds
    Pulse generation (See waveform 3)
    Over Head + Back Door (inside) (key diagnostic mode)
    G79-19 (POS1) - G77-11 (E)
    Output
    W - W-B
    Driver door unlock sensor power source (12 V (drops when power switch turned on (IG)))
    Power switch off → on (IG)
    9 to 14 V → Below 2 V
    -
    G79-21 (POS2) - G77-11 (E)
    Output
    GR - W-B
    Front passenger door unlock sensor power source (12 V (drops when power switch turned on (IG)))
    Power switch off → on (IG)
    9 to 14 V → Below 2 V
    -
    G78-5 (RCO) - G77-11 (E)
    Output
    L - W-B
    Output to door control receiver
    (Power supply for door control receiver. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.)
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. Electrical key transmitter sub-assembly brought outside detection area*2 but kept inside wireless function operational area*3
    4. Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed
    Pulse generation (See waveform 6)
    -
    G78-17 (RDAS) - G77-11 (E)*6
    Input
    LG - W-B
    Door control receiver verifies data received from electrical key transmitter sub-assembly. Door control receiver sends data to ECU and intermittently grounds 12 V signal from certification ECU (smart key ECU assembly).
    Proceed:
    1. Power switch off
    2. All doors locked
    3. Electrical key transmitter sub-assembly brought outside detection area*2 but kept inside wireless function operational area*3
    4. Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed
    Pulse generation (See waveform 7)
    -
    G78-17 (RDAM) - G77-11 (E)*7
    Input
    LG - W-B
    Door control receiver verifies data received from electrical key transmitter sub-assembly. Door control receiver sends data to ECU and intermittently grounds 12 V signal from certification ECU (smart key ECU assembly).
    Procedure:
    1. Power switch off
    2. All doors locked
    3. Electrical key transmitter sub-assembly brought outside detection area*2 but kept inside wireless function operational area*3
    4. Lock or unlock switches of electrical key transmitter sub-assembly not pressed → pressed
    Pulse generation (See waveform 8)
    -
    G78-19 (RSSI) - G77-11 (E)*6
    Output
    R*4 - W-B
    P*5 - W-B
    Door control receiver sends signal to certification ECU (smart key ECU assembly) indicating whether electric waves (example: 312 MHz) from key are being received or not (receiver grounds 12 V signal from certification ECU (smart key ECU assembly))
    Procedure:
    1. All door closed
    2. All door locked
    3. Electrical key transmitter sub-assembly switch not pressed → pressed
    11 to 14 V → Below 2 V
    Key diagnostic mode
    G78-6 (CSEL) - G77-11 (E)*7
    Output
    R - W-B
    Communication channel switching circuit.
    Procedure:
    1. Power switch off
    2. All doors closed
    Below 1 V → Pulse generation
    Key diagnostic mode
    G78-2 (CLG8) - G77-11 (E)
    Output
    V - W-B
    Output to electrical key antenna (outside luggage)
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Back door opener switch assembly off → on
    Pulse generation (See waveform 4)
    Over Head + Back Door
    or
    Luggage + Back Door (key diagnostic mode)
    G78-1 (CG8B) - G77-11 (E)
    Output
    L - W-B
    Output to electrical key antenna (outside luggage) (terminal on opposite side of component from CLG8 output terminal)
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Back door opener switch assembly off → on
    Pulse generation (See waveform 4)
    Over Head + Back Door
    or
    Luggage + Back Door (key diagnostic mode)

    1. *1: For details about the areas that are inside the entry function detection area, refer to Operation Check (Click here).
    2. *2: For details about the areas that are outside the entry function detection area, refer to Operation Check (Click here).
    3. *3: For details about the areas that are inside the wireless function operational area, refer to Operation Check (Click here).
    4. *4: for LHD
    5. *5: for RHD
    6. *6: w/o Tire Pressure Warning System
    7. *7: w/ Tire Pressure Warning System



  5. B251021E01
  6. Using an oscilloscope, check waveform 1.

    HINT:
    The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

    Waveform 1 (Reference) 
    Item
    Content
    Tester Connection
    G79-12 (CLG1) - G77-11 (E)
    G79-11 (CLG2) - G77-11 (E)
    Tool Setting
    2 V/DIV., 500 ms/DIV.
    Condition
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Electrical key transmitter sub-assembly not inside vehicle
    5. Electrical key transmitter sub-assembly brought inside detection area*
    6. All doors locked through wireless operation
    1. *: For details about the areas that are inside the entry function detection area, refer to Operation Check (Click here).



  7. B251024E01
  8. Using an oscilloscope, check waveform 2.

    HINT:
    The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

    Waveform 2 (Reference) 
    Item
    Content
    Tester Connection
    G79-12 (CLG1) - G77-11 (E)
    G79-11 (CLG2) - G77-11 (E)
    Tool Setting
    2 V/DIV., 500 ms/DIV.
    Condition
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Electrical key transmitter sub-assembly not inside vehicle
    5. Electrical key transmitter sub-assembly brought outside detection area*
    6. All doors locked through wireless operation
    1. *: For details about the areas that are outside the entry function detection area, refer to Operation Check (Click here).
    Waveform 2 (Reference) 
    Item
    Content
    Tester Connection
    G79-13 (CG1B) - G77-11 (E)
    G79-10 (CG2B) - G77-11 (E)
    Tool Setting
    2 V/DIV., 500 ms/DIV.
    Condition
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Electrical key transmitter sub-assembly not inside vehicle
    5. Electrical key transmitter sub-assembly brought outside detection area*
    6. All doors locked through wireless operation
    1. *: For details about the areas that are outside the entry function detection area, refer to Operation Check (Click here).



  9. B251020E01
  10. Using an oscilloscope, check waveform 3.

    HINT:
    The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

    Text in Illustration 
    *a
    Door open
    *b
    After approximately 30 seconds from when the door is closed
    Waveform 3 (Reference) 
    Item
    Content
    Tester Connection
    G79-3 (CLG5) - G77-11 (E)
    G79-2 (CG5B) - G77-11 (E)
    G78-11 (CLG6) - G77-11 (E)
    G78-10 (CG6B) - G77-11 (E)
    G78-9 (CLG7) - G77-11 (E)
    G78-8 (CG7B) - G77-11 (E)
    Tool Setting
    2 V/DIV., 500 ms/DIV.
    Condition
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly not inside vehicle
    3. Door is open
    4. Door is closed
    5. Within 30 seconds



  11. B265917E01
  12. Using an oscilloscope, check waveform 4.

    HINT:
    The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

    Text in Illustration 
    *a
    Power switch off, all doors closed and back door opener switch assembly off → on
    Waveform 4 (Reference) 
    Item
    Content
    Tester Connection
    G78-2 (CLG8) - G77-11 (E)
    G78-1 (CG8B) - G77-11 (E)
    Tool Setting
    2 V/DIV., 500 ms/DIV.
    Condition
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Back door opener switch assembly off → on



  13. B251023E01
  14. Using an oscilloscope, check waveform 5.

    HINT:
    The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

    Text in Illustration 
    *a
    In actuality, sampling is being performed
    Waveform 5 (Reference) 
    Item
    Content
    Tester Connection
    G79-20 (TSW1) - G77-11 (E)
    Tool Setting
    2 V/DIV., 500 ms/DIV.
    Condition
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Driver door lock sensor not touched → touched
    Waveform 5 (Reference) 
    Item
    Content
    Tester Connection
    G79-8 (TSW2) - G77-11 (E)
    Tool Setting
    2 V/DIV., 500 ms/DIV.
    Condition
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Front passenger door lock sensor not touched → touched
    Waveform 5 (Reference) 
    Item
    Content
    Tester Connection
    G79-22 (SEN1) - G77-11 (E)
    Tool Setting
    2 V/DIV., 500 ms/DIV
    Condition
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors locked
    4. Electrical key transmitter sub-assembly not sufficiently close to vehicle
    5. Driver door unlock sensor not touched → touched
    Waveform 5 (Reference) 
    Item
    Content
    Tester Connection
    G79-23 (SEN2) - G77-11 (E)
    Tool Setting
    2 V/DIV., 500 ms/DIV.
    Condition
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors locked
    4. Electrical key transmitter sub-assembly not sufficiently close to vehicle
    5. Front passenger door unlock sensor not touched → touched
    Waveform 5 (Reference) 
    Item
    Content
    Tester Connection
    G78-27 (TSW5) - G77-11 (E)
    Tool Setting
    2 V/DIV., 500 ms/DIV
    Condition
    Back door opener switch assembly (unlock switch) off → on
    Waveform 5 (Reference) 
    Item
    Content
    Tester Connection
    G78-28 (TSW6) - G77-11 (E)
    Tool Setting
    2 V/DIV., 500 ms/DIV
    Condition
    Back door opener switch assembly (lock switch) off → on



  15. B251178E01
  16. Using an oscilloscope, check waveform 6.

    HINT:
    The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

    Text in Illustration 
    *a
    Before lock or unlock button of electrical key transmitter sub-assembly pressed
    *b
    After lock or unlock button of electrical key transmitter sub-assembly pressed
    Waveform 6 (Reference) 
    Item
    Content
    Tester Connection
    G78-5 (RCO) - G77-11 (E)
    Tool Setting
    2 V/DIV., 500 ms/DIV.
    Condition
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. Electrical key transmitter sub-assembly brought outside detection area*1 but kept inside wireless function operational area*2
    4. Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed
    1. *1: For details about the areas that are outside the entry function detection area, refer to Operation Check (Click here).
    2. *2: For details about the areas that are inside the wireless function operational area, refer to Operation Check (Click here).



  17. B251177E01
  18. Using an oscilloscope, check waveform 7.

    HINT:
    The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

    Text in Illustration 
    *a
    Before lock or unlock button of electrical key transmitter sub-assembly pressed
    *b
    After lock or unlock button of electrical key transmitter sub-assembly pressed
    Waveform 7 (Reference) 
    Item
    Content
    Tester Connection
    G78-17 (RDAS) - G77-11 (E)
    Tool Setting
    5 V/DIV., 500 ms/DIV.
    Condition
    Proceed:
    1. Power switch off
    2. All doors locked
    3. Electrical key transmitter sub-assembly brought outside detection area*1 but kept inside wireless function operational area*2
    4. Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed
    1. *1: For details about the areas that are outside the entry function detection area, refer to Operation Check (Click here).
    2. *2: For details about the areas that are inside the wireless function operational area, refer to Operation Check (Click here).



  19. B251177E01
  20. Using an oscilloscope, check waveform 8.

    HINT:
    The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

    Text in Illustration 
    *a
    Before lock or unlock switches of electrical key transmitter sub-assembly pressed
    *b
    After lock or unlock switches of electrical key transmitter sub-assembly pressed
    Waveform 8 (Reference) 
    Item
    Content
    Tester Connection
    G78-17 (RDAM) - G77-11 (E)
    Tool Setting
    5 V/DIV., 500 ms/DIV.
    Condition
    Procedure:
    1. Power switch off
    2. All doors locked
    3. Electrical key transmitter sub-assembly brought outside detection area*1 but kept inside wireless function operational area*2
    4. Lock or unlock switches of electrical key transmitter sub-assembly not pressed → pressed
    1. *1: For details about the areas that are outside the entry function detection area, refer to Operation Check (Click here).
    2. *2: For details about the areas that are inside the wireless function operational area, refer to Operation Check (Click here).


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B281049E03


Text in Illustration 
*A
Main body ECU (multiplex network body ECU) with 1 connector
*B
for LHD
*C
for RHD
-
-
*1
Main body ECU (multiplex network body ECU)
-
-

B297238E01


Text in Illustration 
*A
Main body ECU (multiplex network body ECU) with 2 connectors
-
-
*1
Main body ECU (multiplex network body ECU)
-
-
  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item
    MB-11 (GND1) - Body ground
    -
    -
    Ground
    Always
    Below 1 Ω
    -
    MB-30 (BECU) - Body ground
    Input
    -
    Auxiliary battery power supply (for CPU)
    Always
    11 to 14 V
    -
    MB-29 (ACC) - Body ground
    Input
    -
    ACC power supply
    Power switch on (ACC)
    11 to 14 V
    ACC SW
    MB-32 (IG) - Body ground
    Input
    -
    Power switch power supply
    Power switch on (IG)
    11 to 14 V
    IG SW
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Install the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item
    3D-36 (FLCY) - Body ground
    Input
    R - Body ground
    Front door LH courtesy light switch input
    Front door LH open
    Below 1 V
    FL Door Courtesy
    Front door LH closed
    11 to 14 V
    G59-19 (FRCY) - Body ground
    Input
    R - Body ground
    Front door RH courtesy light switch input
    Front door RH open
    Below 1 V
    FR Door Courtesy
    Front door RH closed
    11 to 14 V
    G59-24 (LCTY) - Body ground
    Input
    L - Body ground
    Rear door LH courtesy light switch input
    Rear door LH open
    Below 1 V
    RL Door Courtesy SW
    Rear door LH closed
    Pulse generation (See waveform 3 or 4)
    G59-6 (RCTY) - Body ground
    Input
    G - Body ground
    Rear door RH courtesy light switch input
    Rear door RH open
    Below 1 V
    RR Door Courtesy SW
    Rear door RH closed
    Pulse generation (See waveform 1 or 2)
    3D-35 (BCTY) - Body ground
    Input
    B - Body ground
    Back door courtesy light switch input
    Back door open
    Below 1 V
    Back Door Courtesy SW
    Power switch off, all doors closed and back door closed
    11 to 14 V
    G59-11 (L2) - Body ground
    Input
    SB*1 - Body ground
    B*2 - Body ground
    Driver door key-linked lock input
    Driver door key cylinder in lock position
    Below 1 V
    Door Key SW-Lock
    Power switch off, all doors closed and driver door key cylinder in neutral position
    Pulse generation (See waveform 3 or 4)
    G59-12 (UL2) - Body ground
    Input
    LG*1, G*2 - Body ground
    Driver door key-linked unlock input
    Driver door key cylinder in unlock position
    Below 1 V
    D Door Key SW-UL
    Power switch off, all doors closed and driver door key cylinder in neutral position
    Pulse generation (See waveform 1 or 2)
    3D-11 (ACT+) - Body ground
    Output
    GR - Body ground
    Door lock motor lock drive output
    Driver door control switch not pushed and driver door key cylinder in neutral position
    Below 1 V
    -
    Lock side of driver door control switch pushed or driver door key cylinder in lock position
    11 to 14 V
    3B-2 (ACT+) - Body ground
    Output
    V - Body ground
    Door lock motor lock drive output
    Driver door control switch not pushed and driver door key cylinder in neutral position
    Below 1 V
    -
    Lock side of driver door control switch pushed or driver door key cylinder in lock position
    11 to 14 V
    3B-1 (ACT+) - Body ground
    Output
    Y - Body ground
    Door lock motor lock drive output
    Driver door control switch not pushed and driver door key cylinder in neutral position
    Below 1 V
    -
    Lock side of driver door control switch pushed or driver door key cylinder in lock position
    11 to 14 V
    3D-12 (ACT+) - Body ground
    Output
    L - Body ground
    Door lock motor lock drive output
    Driver door control switch not pushed and driver door key cylinder in neutral position
    Below 1 V
    -
    Lock side of driver door control switch pushed or driver door key cylinder in lock position
    11 to 14 V
    3D-9 (TR+) - Body ground
    Output
    Y - Body ground
    Driver door lock motor unlock drive output
    Back door closed
    Below 1 V
    -
    Back door open
    11 to 14 V
    3D-8 (ACT-) - Body ground
    Output
    P - Body ground
    Door lock motor unlock drive output
    Driver door control switch not pushed and driver door key cylinder in neutral position
    Below 1 V
    -
    Unlock side of driver door control switch pushed or driver door key cylinder in unlock position
    11 to 14 V
    3D-7 (ACT-) - Body ground
    Output
    LG - Body ground
    Door lock motor unlock drive output
    Driver door control switch not pushed and driver door key cylinder in neutral position
    Below 1 V
    -
    Unlock side of driver door control switch pushed or driver door key cylinder in unlock position
    11 to 14 V
    3B-4 (ACT-) - Body ground
    Output
    L - Body ground
    Door lock motor unlock drive output
    Driver door control switch not pushed and driver door key cylinder in neutral position
    Below 1 V
    -
    Unlock side of driver door control switch pushed or driver door key cylinder in unlock position
    11 to 14 V
    3B-3 (ACT-) - Body ground
    Output
    R - Body ground
    Door lock motor unlock drive output
    Driver door control switch not pushed and driver door key cylinder in neutral position
    Below 1 V
    -
    Unlock side of driver door control switch pushed or driver door key cylinder in unlock position
    11 to 14 V
    G59-7 (LSFL) - Body ground
    Input
    L - Body ground
    Front door LH unlock detection switch input
    Front door LH unlocked
    Below 1 V
    FL Door Lock Pos
    Power switch off, all doors closed and front door LH locked
    Pulse generation (See waveform 1 or 2)
    G59-18 (LSFR) - Body ground
    Input
    L - Body ground
    Front door RH unlock detection switch input
    Front door RH unlocked
    Below 1 V
    FR Door Lock Pos
    Power switch off, all doors closed and front door RH locked
    Pulse generation (See waveform 1 or 2)
    3D-24 (LSR) - Body ground
    Input
    Y - Body ground
    Rear door LH unlock detection switch input
    Rear door LH or RH unlocked
    Below 1 V
    RL-Door Lock Pos SW
    Power switch off, all doors closed and rear door LH and RH locked
    Pulse generation (See waveform 3 or 4)
    3D-25 (LSR) - Body ground
    Input
    V - Body ground
    Rear door RH unlock detection switch input
    Rear door RH or LH unlocked
    Below 1 V
    RR-Door Lock Pos SW
    Power switch off, all doors closed and rear door RH and LH locked
    Pulse generation (See waveform 3 or 4)

    1. *1: for LHD
    2. *2: for RHD
    If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.



  5. B199631E01
  6. Using an oscilloscope, check waveform 1.

    HINT:
    The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

    Waveform 1 (Reference)  
    Item
    Content
    Tester Connection
    G59-6 (RCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Rear door RH closed
    Waveform 1 (Reference)  
    Item
    Content
    Tester Connection
    G59-12 (UL2) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Power switch off, all doors closed and driver door key cylinder in neutral position
    Waveform 1 (Reference)  
    Item
    Content
    Tester Connection
    G59-7 (LSFL) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Power switch off, all doors closed and front door LH locked
    Waveform 1 (Reference)  
    Item
    Content
    Tester Connection
    G59-18 (LSFR) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Power switch off, all doors closed and front door RH locked



  7. B199632E01
  8. Using an oscilloscope, check waveform 2.

    HINT:
    The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

    Waveform 2 (Reference)  
    Item
    Content
    Tester Connection
    G59-6 (RCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Rear door RH closed
    Waveform 2 (Reference)  
    Item
    Content
    Tester Connection
    G59-7 (LSFL) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Power switch off, all doors closed and front door LH locked
    Waveform 2 (Reference)  
    Item
    Content
    Tester Connection
    G59-12 (UL2) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Power switch off, all doors closed and driver door key cylinder in neutral position
    Waveform 2 (Reference)  
    Item
    Content
    Tester Connection
    G59-18 (LSFR) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Power switch off, all doors closed and front door RH locked



  9. B201885E01
  10. Using an oscilloscope, check waveform 3.

    HINT:
    The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

    Waveform 3 (Reference)  
    Item
    Content
    Tester Connection
    G59-11 (L2) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Power switch off, all doors closed and driver door key cylinder in neutral position
    Waveform 3 (Reference)  
    Item
    Content
    Tester Connection
    G59-24 (LCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Rear door LH closed
    Waveform 3 (Reference)  
    Item
    Content
    Tester Connection
    3D-24 (LSR) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Power switch off, all doors closed and rear door LH and RH locked
    Waveform 3 (Reference)  
    Item
    Content
    Tester Connection
    3D-25 (LSR) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Power switch off, all doors closed and rear door RH and LH locked



  11. B201886E01
  12. Using an oscilloscope, check waveform 4.

    HINT:
    The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

    Waveform 4 (Reference)  
    Item
    Content
    Tester Connection
    G59-11 (L2) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Power switch off, all doors closed and driver door key cylinder in neutral position
    Waveform 4 (Reference)  
    Item
    Content
    Tester Connection
    G59-24 (LCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Rear door LH closed
    Waveform 4 (Reference)  
    Item
    Content
    Tester Connection
    3D-24 (LSR) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Power switch off, all doors closed and rear door LH and RH locked
    Waveform 4 (Reference)  
    Item
    Content
    Tester Connection
    3D-25 (LSR) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Power switch off, all doors closed and rear door RH and LH locked