Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Entry Function)

SMART ENTRY AND START SYSTEM (for Entry Function) > Front Passenger Side Door Entry Lock and Unlock Functions do not Operate

for Preparation Click here


DESCRIPTION

If the entry lock and unlock functions do not operate for the front passenger door only, the request code may not be being transmitted from the front passenger door or the front door outside handle assembly (for front passenger door) (touch sensor) may be malfunctioning. If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and door control receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door) [front passenger door electrical key antenna]), or there may be wave interference.

HINT:
If the cause of the malfunction is stored in the certification ECU (smart key ECU assembly), the following table is helpful in checking whether or not the malfunction was caused by wave interference.


WIRING DIAGRAM


B349521E22


INSPECTION PROCEDURE

NOTICE:
  1. The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
  2. When using the intelligent tester with the power switch off to troubleshoot:
    Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
  3. Check that there are no electrical key transmitter sub-assemblies in the vehicle.
  4. Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (Click here).
  5. Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution (Click here).
  6. After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
  7. When the entry lock and unlock functions do not operate for doors other than the driver door and if the power switch has not been turned on (IG) for 14 days or more, lock/unlock the doors using the wireless door lock function or key linked unlock operation and then check if the entry door lock and unlock functions operate.

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
  1. When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (Click here).

    OK:
    Door locks operate normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2.CHECK WAVE ENVIRONMENT


    B300378E01
  1. Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the front door outside handle assembly (for front passenger door) and perform an entry function check (Click here).
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Approximately 0.3 m (0.984 ft.)

    NOTICE:
    If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the door handle, communication may not be possible.

    HINT:
    If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

    Result:
    Result
    Proceed to
    Entry function does not operate normally.
    A
    Entry function operates normally.
    B



B
AFFECTED BY WAVE INTERFERENCE
A


3.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)
  1. Disconnect the H11*1, or J11*2 front door outside handle assembly (for front passenger door) connector.

  1. Disconnect the G79 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    1. *1: for LHD
    2. *2: for RHD

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    H11-3 (ANT2) - G79-10 (CG2B)
    Always
    Below 1 Ω
    H11-6 (ANT1) - G79-11 (CLG2)
    Always
    Below 1 Ω
    H11-5 (B) - G79-21 (POS2)
    Always
    Below 1 Ω
    H11-2 (GND) - Body ground
    Always
    Below 1 Ω
    H11-3 (ANT2) or G79-10 (CG2B) - Body ground
    Always
    10 kΩ or higher
    H11-6 (ANT1) or G79-11 (CLG2) - Body ground
    Always
    10 kΩ or higher
    H11-5 (B) or G79-21 (POS2) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    J11-3 (ANT2) - G79-10 (CG2B)
    Always
    Below 1 Ω
    J11-6 (ANT1) - G79-11 (CLG2)
    Always
    Below 1 Ω
    J11-5 (B) - G79-21 (POS2)
    Always
    Below 1 Ω
    J11-2 (GND) - Body ground
    Always
    Below 1 Ω
    J11-3 (ANT2) or G79-10 (CG2B) - Body ground
    Always
    10 kΩ or higher
    J11-6 (ANT1) or G79-11 (CLG2) - Body ground
    Always
    10 kΩ or higher
    J11-5 (B) or G79-21 (POS2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT PASSENGER DOOR ELECTRICAL KEY ANTENNA)


    B250975E44
  1. Disconnect the H11*1 or J11*2 front door outside handle assembly (for front passenger door) connector.

  1. Connect the G79 certification ECU (smart key ECU assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    H11-5 (B) - H11-2 (GND)*1
    J11-5 (B) - J11-2 (GND)*2
    Power switch off → on (IG)
    9 to 14 V → Below 2 V

  1. Using an oscilloscope, check the waveform.

    OK:

    Tester Connection
    Switch Condition
    Tool Setting
    Specified Condition
    H11-3 (ANT2) - H11-6 (ANT1)*1
    J11-3 (ANT2) - J11-6 (ANT1)*2
    Procedure:
    1. Power switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Electrical key transmitter sub-assembly not inside vehicle
    5. Electrical key transmitter sub-assembly brought outside detection area
    6. All doors locked through wireless operation
    2 V/DIV., 500 ms/DIV.
    Pulse generation (See waveform)

    1. *1: for LHD
    2. *2: for RHD
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *1
    Waveform
    *a
    Front view of wire harness connector
    (to Front Door Outside handle assembly (for front passenger door))



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK


5.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR)
  1. Temporarily replace the front door outside handle assembly (for front passenger door) with a new or known good one (Click here).


NEXT


6.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (OPERATION)
  1. Check that the entry functions operate normally (Click here).

    OK:
    Entry functions operate normally.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR) WAS DEFECTIVE)