Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B1498/98    Communication Malfunction (A/C Inverter Local)

for Preparation Click here


DESCRIPTION

The hybrid vehicle control ECU and compressor with motor assembly transmit information to one another via a communication line. Compressor control is stopped and the DTC is stored if communication information is cut off or abnormal information occurs.
The DTC is also detected if high-voltage power supplied from the inverter with converter assembly to the compressor control circuit is shut off.
The DTC will be stored as a history DTC.

DTC No.
DTC Detection Condition
Trouble Area
B1498/98
  1. Communication line error or open between the hybrid vehicle control ECU and compressor with motor assembly.
  1. High-voltage power source is shut off.
  1. Harness or connector between hybrid vehicle control ECU, compressor with motor assembly and body ground
  2. Hybrid vehicle control ECU
  3. Compressor with motor assembly
  4. No. 2 engine wire (harness or connector between compressor with motor assembly and inverter with converter assembly)
  5. Electric vehicle fuse
  6. CAN communication system
  7. Hybrid control system

WIRING DIAGRAM


E235673E33


INSPECTION PROCEDURE

CAUTION:
  1. Wear insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Carry the removed service plug in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.
  2. Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).
  3. The hybrid control system and air conditioning system output DTCs separately. Inspect DTCs following the diagnosis procedure for the hybrid control system first if any DTCs from those systems are output simultaneously.
  4. Depending on the timing of the power supply to the 12 V power supply circuit and high-voltage circuit when the power switch is turned on (READY), an abnormal information signal may be output, causing this DTC to be stored. If the output DTC is a code that was memorized in the past, check the fuses and wire harnesses. If there is no malfunction, clear the DTC.

1.CHECK CAN COMMUNICATION SYSTEM
  1. Use the intelligent tester to check if the CAN communication system is functioning normally.

    Result:
    Result
    Proceed to
    CAN DTC is not output
    A
    CAN DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK DIAGNOSTIC TROUBLE CODE
  1. Check if DTCs for the hybrid control system are output using the intelligent tester.

Result:
Result
Proceed to
DTC is not output
A
Only DTC P3108 is output
A
DTCs other than P3108 are output
B



B
GO TO HYBRID CONTROL SYSTEM (Click here)
A


3.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - BODY GROUND)

CAUTION:
Do not disconnect the connector on the high-voltage side.

  1. Disconnect the C22 compressor with motor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C22-5 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - IG POWER SOURCE, GROUND)
  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    C22-6 (IG1) - C22-5 (GND)
    Power switch on (IG)
    11 to 14 V
    C22-6 (IG1) - C22-5 (GND)
    Power switch off
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - COMPRESSOR WITH MOTOR)
  1. Disconnect the A72 hybrid vehicle control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C22-1 (CLK) - A72-10 (CLK)
    Always
    Below 1 Ω
    C22-2 (DIN) - A72-9 (ITE)
    Always
    Below 1 Ω
    C22-3 (DOUT) - A72-8 (ETI)
    Always
    Below 1 Ω
    C22-1 (CLK) - Body ground
    Always
    10 kΩ or higher
    C22-2 (DIN) - Body ground
    Always
    10 kΩ or higher
    C22-3 (DOUT) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT ELECTRIC VEHICLE FUSE

CAUTION:
Be sure to wear insulated gloves.

  1. Turn the power switch off.

  1. Remove the service plug grip (Click here).

    CAUTION:
    Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.

    NOTICE:
    After removing the service plug grip, turning the power switch on (READY) may cause a malfunction. Do not turn the power switch on (READY) with the service plug grip removed.

  1. Remove the connector cover assembly (Click here).

    NOTICE:
    Be sure to prevent foreign objects or water from entering the inverter with converter assembly.



    E238086E01
  1. Check that bolts A and B are tightened securely.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Item
    (Tester Connection)
    Condition
    Specified Condition
    Electric vehicle fuse
    (A - B)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Electric Vehicle Fuse



NG
REPLACE ELECTRIC VEHICLE FUSE (Click here)
OK


7.INSPECT NO. 2 ENGINE WIRE

CAUTION:
Be sure to wear insulated gloves.

  1. Disconnect the No. 2 engine wire connector (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D1-1 (PE) - D2-1 (ACPE)
    Always
    Below 1 Ω
    D1-2 (PB) - D2-2 (ACPB)
    Always
    Below 1 Ω
    D1-1 (PE) - Body ground
    Always
    10 kΩ or higher
    D1-2 (PB) - Body ground
    Always
    10 kΩ or higher



NG
REPLACE NO. 2 ENGINE WIRE (Click here)
OK


8.REPLACE COMPRESSOR WITH MOTOR ASSEMBLY
  1. Replace the compressor with motor assembly (Click here).

    HINT:
    Since the compressor with motor assembly cannot be inspected while it is removed from the vehicle, replace the compressor with motor assembly with a new or known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1498/98 is not output
    A
    DTC B1498/98 is output
    B



B
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)
A

END (COMPRESSOR WITH MOTOR ASSEMBLY WAS DEFECTIVE)