Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

DTC    U0073/94    Control Module Communication Bus OFF

DTC    U0120/96    Lost Communication with Starter / Generator Control Module

DTC    U0123/62    Lost Communication with Yaw Rate Sensor Module

DTC    U0124/95    Lost Communication with Lateral Acceleration Sensor Module

DTC    U0126/63    Lost Communication with Steering Angle Sensor Module

DTC    U0293/59    Communication Error from HV ECU

for Preparation Click here


DESCRIPTION

The skid control ECU receives signals from the hybrid vehicle control ECU, steering angle sensor (spiral cable with sensor sub-assembly), certification ECU (smart key ECU assembly) and yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system.

DTC No.
INF Code
DTC Detection Condition
Trouble Area
U0073/94
461
Either of the following is detected:
  1. Yaw rate and acceleration sensor communication is disabled for 1 second or more.
  2. Yaw rate and acceleration sensor communication is disabled once or more per 5 seconds 10 times or more within 60 seconds.
  1. CAN communication line (V bus)
  2. Yaw rate and acceleration sensor (Airbag sensor assembly)
  3. Skid control ECU (Brake booster with master cylinder assembly)
↑
462
Either of the following is detected:
  1. Steering angle sensor communication is disabled for 1 second or more.
  2. Steering angle sensor communication is disabled once or more per 5 seconds 10 times or more within 60 seconds.
  1. CAN communication line (V bus)
  2. Steering angle sensor (Spiral cable with sensor sub-assembly)
  3. Skid control ECU (Brake booster with master cylinder assembly)
↑
463
464
Bus off occurs once or more per 0.1 seconds 10 times repeatedly.
  1. CAN communication line
  2. Skid control ECU (Brake booster with master cylinder assembly)
↑
465
466
Sending does not complete within 5 seconds after data is output from the skid control ECU.
↑
U0120/96
471
Push start switch data is invalid for 3 seconds or more.
  1. CAN communication line (V bus)
  2. Certification ECU (Smart key ECU assembly)
  3. Skid control ECU (Brake booster with master cylinder assembly)
U0123/62
731
Yaw rate sensor communication is disabled for 1 second or more.
  1. CAN communication line (V bus)
  2. Yaw rate and acceleration sensor (Airbag sensor assembly)
  3. Skid control ECU (Brake booster with master cylinder assembly)
↑
732
Yaw rate sensor communication is disabled once or more per 5 seconds 10 times or more within 60 seconds.
↑
U0124/95
591
Acceleration sensor communication is disabled for 1 second or more.
  1. CAN communication line (V bus)
  2. Yaw rate and acceleration sensor (Airbag sensor assembly)
  3. Skid control ECU (Brake booster with master cylinder assembly)
↑
592
Acceleration sensor communication is disabled once per 5 seconds 10 times or more within 60 seconds.
↑
U0126/63
741
Steering angle sensor communication is disabled for 1 second or more.
  1. CAN communication line (V bus)
  2. Steering angle sensor (Spiral cable with sensor sub-assembly)
  3. Skid control ECU (Brake booster with master cylinder assembly)
↑
742
Steering angle sensor communication is disabled once or more per 5 seconds 10 times or more within 60 seconds.
↑
U0293/59
411
412
413
Either of the following is detected:
  1. With the IG2 terminal voltage 9.5 V or more, data from the hybrid vehicle control ECU cannot be received for 2 seconds or more.
  2. With the IG2 terminal voltage 9.5 V or more, data from the hybrid vehicle control ECU cannot be received once or more within 5 seconds occur 10 times in succession.
  1. CAN communication line (Sub bus 15)
  2. Hybrid vehicle control ECU
  3. Skid control ECU (Brake booster with master cylinder assembly)

WIRING DIAGRAM


C319737E07


C322207E04


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the intelligent tester, check for any momentary interruptions in the wire harness and connector corresponding to a DTC (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Yaw Rate Open
    Yaw rate sensor open detection / Error or Normal
    Error: Momentary interruption
    Normal: Normal
    -
    Steering Open
    Steering angle sensor open detection / Error or Normal
    Error: Momentary interruption
    Normal: Normal
    -
    HV Communication Open
    Hybrid vehicle communication open detection / Error or Normal
    Error: Momentary interruption
    Normal: Normal
    -

    Result:

    Result
    Proceed to
    There is a constant open circuit.
    A
    There are no momentary interruptions.
    B
    There are momentary interruptions.
    C

    HINT:
    Perform the above inspection before disconnecting any sensors or connectors.



B
Go to step 3

C
Go to step 4
A


2.CHECK IF EACH SENSOR AND ECU CONNECTOR IS SECURELY CONNECTED
  1. Turn the power switch off (lock).

  1. Check if each sensor and ECU connector is securely connected.

    OK:
    Each sensor and ECU connector is securely connected.



NG
CONNECT CONNECTOR TO EACH SENSOR OR ECU CORRECTLY
OK


3.RECONFIRM DTC
  1. Turn the power switch off (lock).

  1. Record the output DTCs (for ABS, VSC, electronically controlled brake system, and/or CAN communication system) (Click here for ABS, VSC and/or electronically controlled brake system, or Click here for CAN communication system).

    HINT:
    If the CAN communication system DTC and the relevant sensor DTCs are output simultaneously, troubleshoot the relevant sensor DTCs (for ABS, VSC and/or electronically controlled brake system) after the CAN communication system returns to normal.


    Result:

    Result
    Proceed to
    DTC is not output.
    A
    ABS, VSC and/or electronically controlled brake system DTC is output.
    B
    CAN communication system DTC is output.
    C



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)

C
INSPECT CAN COMMUNICATION SYSTEM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Turn the power switch off (lock).

  1. Repair or replace the harness or connector.

  1. Check for any momentary interruption between the skid control ECU (brake booster with master cylinder assembly) and each sensor or ECU (Click here).


NEXT


5.RECONFIRM DTC
  1. Turn the power switch off (lock).

  1. Clear the DTCs (Click here).

  1. Turn the power switch on (ready).

  1. Drive the vehicle at a speed of 15 km/h (9 mph) or more and turn the steering wheel to the right and left.

  1. Check that no CAN communication system DTC is output (Click here).

  1. If ABS, VSC and/or electronically controlled brake system DTCs are output, record them (Click here).

    Result:

    Result
    Proceed to
    DTC is not output.
    A
    ABS, VSC and/or electronically controlled brake system DTC is output.
    B
    CAN communication system DTC is output.
    C

    HINT:
    The CAN communication system must be normal when performing troubleshooting for sensor DTCs (for ABS, VSC and/or electronically controlled brake system).



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)

C
INSPECT CAN COMMUNICATION SYSTEM (Click here)
A

END