Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE PEDAL STROKE SENSOR (for RHD)

BRAKE PEDAL STROKE SENSOR (for RHD) > INSTALLATION

for Preparation Click here


NOTICE:
  1. Do not drop the brake pedal stroke sensor assembly.
  2. If the brake pedal stroke sensor assembly has been dropped, replace the brake pedal stroke sensor assembly with a new one.



1. INSPECT AND ADJUST BRAKE PEDAL HEIGHT


  1. Check the brake pedal height.

    1. Turn back the carpet.

    2. Turn back the dash silencer from the slit provided on the dash silencer.



    3. Measure the shortest distance between the brake pedal pad surface and floor panel as shown in the illustration.


      C256180E01


      Text in Illustration 
      *1
      Brake Pedal
      -
      -
      *a
      Brake Pedal Height
      -
      -
      V100144
      Measuring Plane of Floor Panel
      -
      -

      Pedal height from floor panel:
      107.3 to 117.3 mm (4.23 to 4.61 in.)

      If the pedal height is incorrect, adjust it.



  1. Adjust the brake pedal height.



      C249833E01
    1. Remove the stop light switch assembly .
      Text in Illustration 
      *1
      Stop Light Switch Assembly
      *2
      Clevis Lock Nut
      *3
      Floor Panel
      *a
      Brake Pedal Height

    2. Loosen the clevis lock nut.

    3. Adjust the brake pedal height by turning the push rod.

      Pedal height from floor panel:
      107.3 to 117.3 mm (4.23 to 4.61 in.)

    4. Tighten the clevis lock nut.

      Torque:
      26 N*m{ 260 kgf*cm , 19 ft.*lbf }

    5. Install and adjust the stop light switch assembly .



2. INSTALL BRAKE PEDAL STROKE SENSOR ASSEMBLY

NOTICE:
  1. Do not drop the brake pedal stroke sensor assembly.
  2. If the brake pedal stroke sensor assembly has been dropped, replace the brake pedal stroke sensor assembly with a new one.



  1. When installing a new brake pedal stroke sensor assembly:

    NOTICE:
    Do not break the brake pedal stroke sensor assembly lever set pin before installing the brake pedal stroke sensor assembly with the bolt.




      C249815E01
    1. Install a new brake pedal stroke sensor assembly to the brake pedal support assembly with the 2 bolts.
      Text in Illustration 
      *1
      Brake Pedal Stroke Sensor Assembly Lever
      *a
      Brake Pedal Groove

      Torque:
      8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

      NOTICE:
      1. Engage the brake pedal stroke sensor assembly lever with the brake pedal groove.
      2. Check that there is no foreign matter attached to the contact surface of the brake pedal stroke sensor assembly.
      3. Check that the tip of the brake pedal stroke sensor assembly lever is protruding from the brake pedal groove.

    2. Connect the connector.

    3. Firmly depress the brake pedal and break the brake pedal stroke sensor assembly lever set pin.

    4. Remove the broken lever set pin.



  1. When reusing the brake pedal stroke sensor assembly:



      C249815E01
    1. Install the brake pedal stroke sensor assembly to the brake pedal support assembly and temporarily tighten the 2 bolts.
      Text in Illustration 
      *1
      Brake Pedal Stroke Sensor Assembly Lever
      *a
      Brake Pedal Groove

      NOTICE:
      1. Engage the brake pedal stroke sensor assembly lever with the brake pedal groove.
      2. Check that there is no foreign matter attached to the contact surface of the brake pedal stroke sensor assembly.
      3. Check that the tip of the brake pedal stroke sensor assembly lever is protruding from the brake pedal groove.

      HINT:
      Fully tighten the 2 bolts when adjusting the brake pedal stroke sensor assembly.

    2. Connect the connector.



3. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL



4. ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY

NOTICE:
When the brake pedal stroke sensor assembly is being reused, perform the following procedure to adjust it.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List "Stroke Sensor".



    C249817
  1. Read the stroke sensor value in the Data List, and turn the brake pedal stroke sensor assembly slowly to the right or left to adjust the output voltage so that it is within the following range.

    Standard voltage (without the brake pedal depressed):
    0.8 to 1.2 V



    C249818
  1. Tighten the 2 bolts.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    Do not depress the brake pedal after turning the power switch on (IG).

  1. Turn the intelligent tester off and turn the power switch off.

  1. Disconnect the intelligent tester.



5. CHECK AND CLEAR DTC
(Click here)


6. PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE
(Click here)