LIGHTING SYSTEM > Headlight Dimmer Switch Circuit |

| 1.READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Dimmer SW | Dimmer switch high position signal/ON or OFF | ON: Dimmer switch in high or high flash position OFF: Dimmer switch in low position | - |
| Passing Light SW | Dimmer switch high flash position (pass) signal/ON or OFF | ON: Dimmer switch in high flash position OFF: Dimmer switch not in high flash position | - |
| Front Fog Light SW | Front fog light switch signal/ON or OFF | ON: Front fog light switch on OFF: Front fog light switch off | * |
| Head Light SW (Head) | Light control switch head position signal/ON or OFF | ON: Light control switch in head position OFF: Light control switch not in head position | - |
| Head Light SW (Tail) | Light control switch tail position signal/ON or OFF | ON: Light control switch in tail or head position OFF: Light control switch in neither tail nor head position | - |
|
| ||||
| OK | ||
| ||
| 2.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY |
Remove the headlight dimmer switch assembly (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 13 (T) - 19 (EL) | Light control switch off | 10 kΩ or higher |
| 11 (H) - 19 (EL) | Light control switch off | 10 kΩ or higher |
| 13 (T) - 19 (EL) | Light control switch in tail position | Below 1 Ω |
| 13 (T) - 19 (EL) | Light control switch in head position | Below 1 Ω |
| 11 (H) - 19 (EL) | Light control switch in head position | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| 20 (HU) - 19 (EL) | Dimmer switch in low position | 10 kΩ or higher |
| 20 (HU) - 19 (EL) | Dimmer switch in high position | Below 1 Ω |
| 14 (HF) - 19 (EL) | Dimmer switch in high flash position | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| 7 (BFG) - 8 (LFG) | Font fog light switch off | 10 kΩ or higher |
| 7 (BFG) - 8 (LFG) | Font fog light switch on | Below 1 Ω |
| *A | w/ Front Fog Light |
| *a | Component without harness connected (Headlight Dimmer Switch Assembly) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU - HEADLIGHT DIMMER SWITCH ASSEMBLY) |
Disconnect the G59 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G9-7 (BFG) - G59-27 (FFOG)* | Always | Below 1 Ω |
| G9-20 (HU) - G59-5 (HU) | Always | Below 1 Ω |
| G9-14 (HF) - G59-8 (HF) | Always | Below 1 Ω |
| G9-13 (T) - G59-30 (TAIL) | Always | Below 1 Ω |
| G9-11 (H) - G59-29 (HEAD) | Always | Below 1 Ω |
| G9-7 (BFG) - Body ground* | Always | 10 kΩ or higher |
| G9-20 (HU) - Body ground | Always | 10 kΩ or higher |
| G9-14 (HF) - Body ground | Always | 10 kΩ or higher |
| G9-13 (T) - Body ground | Always | 10 kΩ or higher |
| G9-11 (H) - Body ground | Always | 10 kΩ or higher |
| G9-19 (EL) - Body ground | Always | Below 1 Ω |
| G9-8 (LFG) - Body ground* | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||