Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Fuel Receiver Gauge Malfunction

for Preparation Click here


DESCRIPTION

  1. The meter ECU uses the fuel sender gauge assembly to determine the level of the fuel in the fuel tank. The resistance of the fuel sender gauge will vary between approximately 13 Ω with the float at the full position, and 414 Ω with the float at the empty position. The meter outputs auxiliary battery voltage through two resistors that are mounted inside the meter ECU. The meter ECU measures the voltage between the variable resistor in the fuel sender gauge and the two resistors mounted in the meter. Voltage measured at this point will vary as the float of the fuel sender gauge is moved. The highest voltage observed should be approximately half of the auxiliary battery voltage.

HINT:
The fuel level warning light will come on when the fuel level is below 4.7 liters (5.0 US qts, 4.1 Imp.qts).


WIRING DIAGRAM


E237325E01


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FUEL METER OPERATION)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Combination Meter / Active Test.

  1. Check the operation by referring to the table below.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Fuel Meter Operation
    Fuel receiver gauge
    Empty, 1/2, Full
    -

    OK:
    Fuel receiver gauge indication is normal.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


2.READ VALUE USING INTELLIGENT TESTER (FUEL INPUT)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Combination Meter / Data List.

  1. Check the values by referring to the table below.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Fuel Input
    Fuel input/Min.: 0, Max.: 127.5
    10th segment comes on: 31.7 to 36.0
    Unit: Liter
    9th segment comes on: 28.3 to 31.7
    8th segment comes on: 25.0 to 28.3
    7th segment comes on: 21.6 to 25.0
    6th segment comes on: 18.2 to 21.6
    5th segment comes on: 14.8 to 18.2
    4th segment comes on: 11.5 to 14.8
    3rd segment comes on: 8.1 to 11.5
    2nd segment comes on: 4.7 to 8.1
    1st segment comes on: 3.8 to 4.7

    Result:

    Result
    Proceed to
    Fuel level data displayed on the intelligent tester differs from the fuel receiver gauge indication.
    A
    Fuel level data displayed on the intelligent tester is almost the same as the fuel receiver gauge indication.
    B



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE)
  1. Disconnect the G1 combination meter assembly connector.

  1. Disconnect the M22 fuel sender gauge assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G1-2 (L) - M22-2 (FS)
    Always
    Below 1 Ω
    G1-2 (L) - Body ground
    Always
    10 kΩ or higher
    M22-3 (FE) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT FUEL SENDER GAUGE ASSEMBLY
  1. Remove the fuel sender gauge assembly (Click here).



  1. Type A



      A267870E02
    1. Check that the float moves smoothly between E and F.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1 - 2
      Float level is F (upper)
      12.0 to 18.0 Ω
      1 - 2
      Float level is between F (upper) and E (lower)
      12.0 to 415.0 Ω (Gradually changes)
      1 - 2
      Float level is E (lower)
      405.0 to 415.0 Ω

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Fuel Sender Gauge Assembly)



  1. Type B



      A307401E01
    1. Check that the float moves smoothly between E and F.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1 - 2
      Float level is F (upper)
      13.5 to 16.5 Ω
      1 - 2
      Float level is between F (upper) and E (lower)
      13.5 to 414.5 Ω (Gradually changes)
      1 - 2
      Float level is E (lower)
      405.5 to 414.5 Ω

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Fuel Sender Gauge Assembly)



B
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
A


5.CHECK FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE
  1. Visually check for deformation on the fuel suction tube assembly with pump and gauge connector.

    OK:
    There is no deformation.



NG
REPLACE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE (Click here)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)