Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB BOLT

FRONT AXLE HUB BOLT > REPLACEMENT

for Preparation Click here


NOTICE:
  1. When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be output. As there is no malfunction, clear the DTC.
  2. While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or the door courtesy switch is turned on. Therefore, even if only brake shoes are to be removed and installed, be sure to perform the Disable Brake Control procedure and disconnect the cable from the negative (-) terminal of the auxiliary battery before beginning work.

HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedure listed below is for the LH side.



1. PRECAUTION

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (Click here).



2. DISABLE BRAKE CONTROL
  1. Wait at least 2 minutes after turning the power switch off.

    NOTICE:
    When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.



    C250008
  1. Disconnect the reservoir level switch connector with the parking brake applied.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal (Click here).

  1. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

  1. Check that the brake pedal can not be further depressed.

  1. Release the parking brake.



3. REMOVE FRONT WHEEL


4. SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY
  1. Remove the 2 bolts and separate the front disc brake caliper assembly from the steering knuckle.

    NOTICE:
    Use wire or an equivalent tool to keep the front disc brake caliper assembly from hanging down by the front flexible hose.



5. REMOVE FRONT DISC


    C249590E01
  1. Remove the front disc.
    Text in Illustration 
    *a
    Matchmark

    HINT:
    Put matchmarks on the disc and the axle hub.



6. REMOVE FRONT AXLE HUB BOLT


    C249880E01
  1. Temporarily install 2 service nuts to the front axle hub bolts as shown in the illustration.
    Text in Illustration 
    *1
    Service Nut

    Recommended service nut:
    Thread diameter: 12.0 mm (0.472 in.)
    Thread pitch: 1.5 mm (0.0591 in.)

    NOTICE:
    Install the service nuts to prevent damage to the hub bolts.

  1. Using SST and a screwdriver or an equivalent tool to hold the front axle hub, remove the front axle hub bolt.

    SST
    09628-10011  

    NOTICE:
    Do not damage the threads of the front axle hub bolts.



7. INSTALL FRONT AXLE HUB BOLT
  1. Temporarily install a new front axle hub bolt to the front axle hub.



    C249881E01
  1. Install a washer and service nut to the new front axle hub bolt as shown in the illustration.
    Text in Illustration 
    *1
    Service Nut
    *2
    Washer

    Recommended service nut:
    Thread diameter: 12.0 mm (0.472 in.)
    Thread pitch: 1.5 mm (0.0591 in.)

    HINT:
    Recommended washer thickness is 5 mm (0.197 in.) or more.

  1. Using a screwdriver or an equivalent tool to hold the front axle hub, install the hub bolt by tightening the service nut.

    NOTICE:
    1. Install the service nuts to prevent damage to the front axle hub bolts.
    2. Do not damage the threads of the front axle hub bolts.

  1. Remove the 3 service nuts and washer from the 3 front axle hub bolts.



8. INSTALL FRONT DISC


    C249590E01
  1. Align the matchmarks of the disc and axle hub, and install the front disc.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    When replacing the disc with a new one, select the installation position where the front disc has minimal runout.



9. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY
  1. Install the front disc brake caliper assembly to the steering knuckle with the 2 bolts.

    Torque:
    107 N*m{ 1089 kgf*cm , 79 ft.*lbf }

    NOTICE:
    Do not twist the front flexible hose when installing the front disc brake caliper assembly.



10. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



11. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
  1. Connect the cable to the negative (-) auxiliary battery terminal .

  1. Connect the reservoir level switch connector.

  1. Clear the DTCs (Click here).