Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM

SEAT BELT WARNING SYSTEM > Front Passenger Side Seat Belt Warning Light Malfunction

for Preparation Click here


DESCRIPTION

The occupant detection sensor (separate type front seat cushion pad) detects if the front passenger seat is occupied and sends signals to the combination meter assembly. The front seat inner belt assembly (for front passenger) detects the front passenger seat belt condition and sends signals to the combination meter assembly. After receiving the signals from the occupant detection sensor (separate type front seat cushion pad) and front seat inner belt assembly (for front passenger), the seat belt warning light on the combination meter assembly will blink or go off.

HINT:
The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


WIRING DIAGRAM


B275873E06


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Combination Meter / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P-Seatbelt Buckle SW
    Front passenger seat belt buckle switch signal/ON or OFF
    ON: Front passenger seat belt unfastened
    OFF: Front passenger seat belt fastened
    Front passenger seat occupied

    OK:
    ON or OFF appears on the tester screen according to the front passenger seat belt condition.



NG
Go to step 2
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER - FRONT SEAT INNER BELT - BODY GROUND)
  1. Disconnect the G1 combination meter assembly connector.

  1. Disconnect the M11*1 or M9*2 front seat inner belt assembly (for front passenger) connector.

  1. Measure the resistance according to the value(s) in the table below.

    1. *1: for LHD
    2. *2: for RHD

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    G1-12 (SW) - M11-3
    Always
    Below 1 Ω
    G1-12 (SW) - Body ground
    Always
    10 kΩ or higher
    M11-2 - Body ground
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    G1-12 (SW) - M9-3
    Always
    Below 1 Ω
    G1-12 (SW) - Body ground
    Always
    10 kΩ or higher
    M9-2 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD)


    B218574E01
  1. Remove the occupant detection sensor (separate type front seat cushion pad) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 3
    Front passenger seat occupied
    Below 100 Ω
    1 - 3
    Front passenger seat not occupied
    1 MΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Occupant Detection Sensor (Separate Type Front Seat Cushion Pad))



NG
REPLACE OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD) (Click here)
OK


4.INSPECT FRONT SEAT INNER BELT ASSEMBLY (FOR FRONT PASSENGER)


    B271152E14
  1. Remove the front seat inner belt assembly (for front passenger) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    M11-3 - B-1
    Always
    Below 1 Ω
    M11-2 - B-3
    Front passenger seat belt unfastened
    Below 1 Ω
    M11-2 - B-3
    Front passenger seat belt fastened
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    M9-3 - B-1
    Always
    Below 1 Ω
    M9-2 - B-3
    Front passenger seat belt unfastened
    Below 1 Ω
    M9-2 - B-3
    Front passenger seat belt fastened
    10 kΩ or higher

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Component without harness connected
    (Front Seat Inner Belt Assembly (for Front Passenger))



NG
REPLACE FRONT SEAT INNER BELT ASSEMBLY (FOR FRONT PASSENGER) (Click here)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)