Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

POWER WINDOW CONTROL SYSTEM > Key-off Operation Function Operates even if Operating Conditions are not Satisfied

for Preparation Click here


DESCRIPTION

  1. When the front doors are closed, each power window regulator motor assembly can control its power window operation for approximately 43 seconds after the power switch is turned from on (IG) to off by receiving operation permission signals from the main body ECU (multiplex network body ECU).
  2. However, when approximately 43 seconds have elapsed, or the driver door or front passenger door is opened within approximately 43 seconds of the power switch being turned off, the power window regulator motor assembly stops operating.
  3. During an auto operation, when 43 seconds have passed and key-off operation is prohibited, the window continues the operation until the auto operation is completed.

INSPECTION PROCEDURE

NOTICE:
The power window control system uses a LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the power window control system after confirming that the communication system is functioning properly.

1.CHECK MANUAL UP / DOWN FUNCTION
  1. Check that the manual up and down functions using the power window regulator master switch assembly and power window regulator switch assembly can operate all the power windows (Click here).

    OK:
    Manual up and down functions are normal.



NG
GO TO OTHER PROBLEM (Proceed to Problem Symptoms Table) (Click here)
OK


2.CHECK REMOTE UP / DOWN FUNCTION
  1. Check that the remote up and down functions using the power window regulator master switch assembly can operate all the power windows (Click here).

    OK:
    Remote up and down functions are normal.



NG
GO TO OTHER PROBLEM (Proceed to Problem Symptoms Table) (Click here)
OK


3.CHECK OPERATION FUNCTION AFTER POWER SWITCH IS TURNED OFF
  1. Check the power window operation function after the power switch is turned off.

    Result:

    Result
    Proceed to
    When power window can still be operated even after opening driver door or front passenger door within approximately 43 seconds of power switch being turned off
    A
    When power window can still be operated even after approximately 43 seconds have elapsed after power switch is turned off (for All Doors)
    B
    When power window can still be operated even after approximately 43 seconds have elapsed after power switch is turned off (for Driver Door)
    C
    When power window can still be operated even after approximately 43 seconds have elapsed after power switch is turned off (Front Passenger Door, Rear LH Door or Rear RH Door)
    D



B
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)

C
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR) (Click here)

D
Go to step 5
A


4.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch to on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Door Courtesy
    Front door courtesy light switch RH / OPEN or CLOSE
    CLOSE: Front door RH closed
    OPEN: Front door RH open
    -
    FL Door Courtesy
    Front door courtesy light switch LH / OPEN or CLOSE
    CLOSE: Front door LH closed
    OPEN: Front door LH open
    -

    OK:
    On the intelligent tester screen, ON or OFF is displayed accordingly.



NG
GO TO LIGHTING SYSTEM (Proceed to Front Door Courtesy Switch Circuit) (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

5.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
  1. Replace the main body ECU (multiplex network body ECU) (Click here).


NEXT


6.CHECK POWER WINDOW CONTROL SYSTEM
  1. Check the power window operation function after the power switch is turned off.

    OK:
    The power window control system operates normally.



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)