Home › Engine / Hybrid System › 1NZ-FXE FUEL › FUEL INJECTOR

FUEL INJECTOR > INSTALLATION

for Preparation Click here



1. INSTALL FUEL INJECTOR ASSEMBLY


    A115499E04
  1. Apply a light coat of gasoline or spindle oil to new O-rings, and then install one onto each fuel injector.
    Text in Illustration 
    *1
    O-ring

  1. Apply a light coat of gasoline or spindle oil to the contact surfaces of the new O-ring on each fuel injector assembly.



    A265003E02
  1. While turning the fuel injector assembly left and right, install it onto the fuel delivery pipe sub-assembly.
    Text in Illustration 
    V100135
    Push
    V100136
    Turn

    NOTICE:
    1. Make sure that the O-ring is not cracked or jammed when installing the injector (Click here).
    2. If a component has been dropped or subjected to a strong impact, replace it.

    HINT:
    Perform "Inspection After Repairs" after replacing the fuel injector assembly (Click here).

  1. Check that the fuel injector rotates smoothly. If the fuel injector does not rotate, replace the O-ring.



2. INSTALL INJECTOR VIBRATION INSULATOR
  1. Install 4 new injector vibration insulators onto the cylinder head.



3. INSTALL FUEL DELIVERY SPACER


    A265002E01
  1. Install the 2 fuel delivery spacers onto the cylinder head.
    Text in Illustration 
    *1
    Fuel Delivery Spacer
    *a
    Fuel Delivery Pipe Side
    *b
    Cylinder Head Side

    NOTICE:
    Install the fuel delivery spacer in the correct direction.



4. INSTALL FUEL DELIVERY PIPE


    A265000
  1. Install the fuel delivery pipe with the 4 fuel injector assemblies and install the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    NOTICE:
    1. Do not drop the fuel injectors when installing the fuel delivery pipe.
    2. Check that the fuel injector assemblies rotate smoothly after installing the fuel delivery pipe.

  1. Engage the clamp to connect the wire harness.



    A264999
  1. Install the bolt to secure the fuel delivery pipe.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



5. CONNECT FUEL TUBE SUB-ASSEMBLY


    A264998E01
  1. Push the tube connector into the pipe until the tube connector makes a "click" sound.
    Text in Illustration 
    V100135
    Push

    NOTICE:
    1. Before connecting the fuel tube connector and fuel delivery pipe, check that there is no damage or foreign matter on the connecting part of the fuel delivery pipe.
    2. After connecting the fuel tube connector and fuel delivery pipe, check that they are securely connected by trying to pull them apart.



6. INSTALL EFI FUEL PIPE CLAMP
  1. Install the EFI fuel pipe clamp.



7. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
  1. Install a new gasket to the cylinder head cover sub-assembly.



    A267067
  1. Apply seal packing to the 2 locations shown in the illustration.
    Text in Illustration 
    V100135
    Apply Seal Packing

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover within 3 minutes of applying seal packing.
    3. Do not start the engine for at least 2 hours after installation.



    A265764E01
  1. Temporarily install the cylinder head cover sub-assembly with the 9 bolts, 2 nuts and 2 new seal washers.
    Text in Illustration 
    *1
    Seal Washer

  1. Using several steps, uniformly tighten the bolts and nuts in the sequence shown in the illustration.

    Torque:
    13 N*m{ 132 kgf*cm , 10 ft.*lbf }

  1. Connect the No. 1 ventilation hose and No. 2 ventilation hose.



8. CONNECT ENGINE WIRE (for LHD)
  1. Install the engine wire with the 3 bolts.

    Torque:
    8.4 N*m{ 85 kgf*cm , 74 in.*lbf }

  1. Connect the wire harness clamp.

  1. Connect the 4 injector connectors.



9. CONNECT ENGINE WIRE (for RHD)
  1. Install the engine wire with the 3 bolts.

    Torque:
    8.4 N*m{ 85 kgf*cm , 74 in.*lbf }

  1. Connect the 4 injector connectors.



10. INSTALL BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY
  1. Install the brake master cylinder reservoir assembly to the reservoir bracket with the 2 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



11. INSTALL NO. 1 IGNITION COIL


    A268161E01
  1. Install the 4 No. 1 ignition coils with the 4 bolts.
    Text in Illustration 
    *a
    Body
    *b
    Cap

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    If the body or cap of the No. 1 ignition coil is dropped or subjected to a strong impact, replace the No. 1 ignition coil with a new one.

    HINT:
    Perform "Inspection After Repairs" after replacing the ignition coil assembly (Click here).

  1. Connect the 4 No. 1 ignition coil connectors.



12. INSTALL EGR VALVE WITH COOLER ASSEMBLY
(Click here)


13. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



14. INSTALL FRONT FLOOR COVER RH
  1. Engage the 3 guides.



    B301488E01
  1. Engage the clip <B> to install the front floor cover RH.

  1. Install the 2 clips <A>.



15. INSPECT FOR FUEL LEAK
  1. Check fuel pump operation.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG) and turn the intelligent tester on.

      NOTICE:
      Do not start the engine.

    3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

    4. Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.

  1. Inspect for fuel leaks.

    1. Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.

  1. Turn the power switch off.

  1. Disconnect the intelligent tester from the DLC3.



16. INSPECT FOR ENGINE OIL LEAK