FUEL INJECTOR > INSTALLATION |
| 1. INSTALL FUEL INJECTOR ASSEMBLY |
![]() |
Apply a light coat of gasoline or spindle oil to new O-rings, and then install one onto each fuel injector.
| *1 | O-ring |
Apply a light coat of gasoline or spindle oil to the contact surfaces of the new O-ring on each fuel injector assembly.
![]() |
While turning the fuel injector assembly left and right, install it onto the fuel delivery pipe sub-assembly.
![]() | Push |
![]() | Turn |
Check that the fuel injector rotates smoothly. If the fuel injector does not rotate, replace the O-ring.
| 2. INSTALL INJECTOR VIBRATION INSULATOR |
Install 4 new injector vibration insulators onto the cylinder head.
| 3. INSTALL FUEL DELIVERY SPACER |
![]() |
Install the 2 fuel delivery spacers onto the cylinder head.
| *1 | Fuel Delivery Spacer |
| *a | Fuel Delivery Pipe Side |
| *b | Cylinder Head Side |
| 4. INSTALL FUEL DELIVERY PIPE |
![]() |
Install the fuel delivery pipe with the 4 fuel injector assemblies and install the 2 bolts.
Engage the clamp to connect the wire harness.
![]() |
Install the bolt to secure the fuel delivery pipe.
| 5. CONNECT FUEL TUBE SUB-ASSEMBLY |
![]() |
Push the tube connector into the pipe until the tube connector makes a "click" sound.
![]() | Push |
| 6. INSTALL EFI FUEL PIPE CLAMP |
Install the EFI fuel pipe clamp.
| 7. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY |
Install a new gasket to the cylinder head cover sub-assembly.
![]() |
Apply seal packing to the 2 locations shown in the illustration.
![]() | Apply Seal Packing |
![]() |
Temporarily install the cylinder head cover sub-assembly with the 9 bolts, 2 nuts and 2 new seal washers.
| *1 | Seal Washer |
Using several steps, uniformly tighten the bolts and nuts in the sequence shown in the illustration.
Connect the No. 1 ventilation hose and No. 2 ventilation hose.
| 8. CONNECT ENGINE WIRE (for LHD) |
![]() |
Connect the wire harness clamp.
Connect the engine wire to the engine room main wire.
![]() |
Connect the engine wire to the engine room relay block and junction block assembly and engage the claw.
Connect the wire harness clamp and 2 connectors.
![]() |
Connect the 2 wire harness clamps.
Connect the ECM connector and lower the lever.
| 9. CONNECT ENGINE WIRE (for RHD) |
![]() |
Connect the wire harness clamp.
Connect the engine wire to the engine room main wire.
![]() |
Connect the engine wire to the engine room relay block and junction block assembly and engage the claw.
Connect the wire harness clamp and 2 connectors.
![]() |
Connect the ECM connector and lower the lever.
| 10. INSTALL BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY |
Install the brake master cylinder reservoir assembly to the reservoir bracket with the 2 nuts.
| 11. INSTALL NO. 1 IGNITION COIL |
![]() |
Install the 4 No. 1 ignition coils with the 4 bolts.
| *a | Body |
| *b | Cap |
Connect the 4 No. 1 ignition coil connectors.
| 12. INSTALL EGR VALVE WITH COOLER ASSEMBLY |
| 13. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL |
| 14. INSTALL FRONT FLOOR COVER RH |
Engage the 3 guides.
![]() |
Engage the clip <B> to install the front floor cover RH.
Install the 2 clips <A>.
| 15. INSPECT FOR FUEL LEAK |
Check fuel pump operation.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG) and turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.
Inspect for fuel leaks.
Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.
Turn the power switch off.
Disconnect the intelligent tester from the DLC3.
| 16. INSPECT FOR ENGINE OIL LEAK |