Home › General › INTRODUCTION › REPAIR INSTRUCTION

REPAIR INSTRUCTION > INITIALIZATION



PROCEDURES NECESSARY WHEN AUXILIARY BATTERY TERMINAL IS DISCONNECTED/RECONNECTED

Necessary Procedures
Effect/Inoperative Function When Necessary Procedures are not Performed
See page
Unlock back door
Back door opener
Click here

PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED

Replacement Part
Necessary Procedure
Effect/Inoperative Function when Necessary Procedures are not Performed
See page
ECM
Vehicle Identification Number (VIN) or frame number registration
MIL comes on
Click here
  1. Throttle body with motor assembly
  2. Cleaning the deposits from the throttle with motor body assembly
  3. Engine assembly
  4. Cylinder head sub-assembly
  5. Camshaft (for intake or exhaust camshaft)
  6. Camshaft timing gear assembly
  7. Piston or piston ring
  8. Mass air flow meter sub-assembly
  9. Fuel injector assembly
  10. Fuel pump with filter assembly
  11. Air fuel ratio sensor
  12. Engine coolant temperature sensor
  13. Spark plug
  14. Ignition coil assembly
  15. EGR valve assembly
  16. Air leaks from intake system
  17. Gas leaks from exhaust system
  18. Knock control sensor
Inspection after repair
Poor idle, engine starting, etc
Click here
  1. Door control and tire pressure monitoring system receiver assembly
  2. Tire pressure warning valve and transmitter
  1. Transmitter ID registration
  2. Initialization
  1. When DTC detection conditions of "transmitter ID not received" DTC are met, TPWS indicator blinks for 1 minute, and then illuminates.
  2. Tire pressure warning function
Click herefor Registration
Click herefor Initialization
Brake booster with master cylinder assembly
  1. Initialization and calibration of the linear solenoid valve
  2. Yaw rate and acceleration sensor zero point calibration
  1. ABS warning light illumination
  2. Brake warning light/yellow (minor malfunction) illumination
  3. Slip indicator light illumination
  4. VSC disable or malfunctioning
Click here for Initialization
Click here for Calibration
  1. Brake pedal stroke sensor assembly
  2. Brake pedal
  1. Clearing stored linear solenoid valve calibration data
  2. Initialization and calibration of the linear solenoid valve
Click here
Yaw rate and acceleration sensor (air bag sensor assembly)
  1. Clearing zero point calibration data
  2. Yaw rate and acceleration sensor zero point calibration
Click here
Power steering ECU assembly
  1. Torque sensor zero point calibration
  2. Assist map writing
  1. P/S warning light comes on
  2. EPS control
Click here
Electric power steering column sub-assembly
Torque sensor zero point calibration
Steering effort is different between turning steering wheel to left and right
  1. Certification ECU (smart key ECU assembly)
  2. Steering lock ECU (steering lock actuator assembly)
  3. ID code box (immobiliser code ECU)
  4. Hybrid vehicle control ECU
  5. Electrical key transmitter sub-assembly
Code registration (Engine immobiliser system)
  1. Wireless door lock control system
  2. Smart entry and start system
  3. Hybrid control system start
  4. Steering lock system
See Service Bulletin for the registration method
  1. No. 1 air conditioning radiator damper servo sub-assembly
  2. No. 2 air conditioning radiator damper servo sub-assembly
  3. No. 1 blower damper servo sub-assembly
Initialization servo motor (Air conditioning system)
DTCs are output
Click here
  1. Door window regulator assembly
  2. Power window regulator motor assembly
  3. Door glass
  4. Door glass run
Initialize power window control system
  1. Auto up/down function
  2. Jam protection function
  3. Operation function after power switch is turned off
Click here
  1. Headlight leveling ECU assembly
  2. Rear height control sensor sub-assembly
Perform headlight leveling ECU initialization
Automatic headlight beam level control function
Click here