Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM

ELECTRONICALLY CONTROLLED BRAKE SYSTEM > VSC OFF Switch Circuit

for Preparation Click here


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) is connected to the combination meter assembly via CAN communication.
Pressing the VSC OFF switch turns off TRC operation, and pressing and holding this switch turns off TRC and VSC operation. If TRC and VSC operations are turned off, the TRC OFF message will be displayed on the multi-information display and the VSC OFF indicator light will come on.

WIRING DIAGRAM


C319941E03


INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU (brake booster with master cylinder assembly) , perform initialization and calibration of the linear solenoid valve (Click here).

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if CAN communication system DTCs are output (Click here).

    Result:

    Result
    Proceed to
    DTCs are not output
    A
    DTCs are output
    B



B
INSPECT CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
  1. Check if the skid control ECU (brake booster with master cylinder assembly) connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


3.READ VALUE USING INTELLIGENT TESTER (TRC/VSC OFF MODE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Select the Data List on the intelligent tester (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    TRC/VSC Off Mode
    TRC/VSC off mode / Normal, TRC OFF, Unknown or VSC OFF
    Normal: Normal mode
    TRC OFF: TRC off mode
    Unknown: Unspecified
    VSC OFF: VSC off mode
    -

  1. Check the indicator light and mode condition on the intelligent tester changes according to VSC OFF switch operation.

    Standard:

    Switch Operation
    Mode Condition Display
    Multi-information Display (TRC OFF message)
    VSC OFF Indicator Light
    Not pressed
    Normal
    Not displayed
    Does not come on
    Pressing the VSC OFF switch
    TRC OFF
    Displayed
    Does not come on
    Pressing and holding the VSC OFF switch
    VSC OFF
    Displayed
    Comes on


    Result:

    Result
    Proceed to
    Indicator light and mode condition display do not change
    A
    Mode condition display is normal, but indicator light does not change
    B
    Indicator light and mode condition display is normal
    C



B
INSPECT METER / GAUGE SYSTEM (Click here)

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MULTI-INFORMATION DISPLAY (TRC OFF MESSAGE) AND VSC OFF INDICATOR LIGHT)
  1. Select the Active Test on the intelligent tester (Click here).

    ABS/VSC/TRC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    TRC(TRAC) OFF Indicator Light
    Multi-information display (TRC OFF message)
    Display ON/OFF
    Observe combination meter assembly
    VSC OFF Indicator Light
    VSC OFF indicator light
    Indicator light ON/OFF
    Observe combination meter assembly

  1. Check the multi-information display (TRC OFF message) and VSC OFF indicator light in the combination meter assembly turns on or off in accordance with intelligent tester operation.

    OK:
    The multi-information display (TRC OFF message) and VSC OFF indicator light turns on or off in accordance with intelligent tester operation.



NG
Go to step 7
OK


5.INSPECT VSC OFF SWITCH


    C239020E06
  1. Turn the power switch off.

  1. Disconnect the VSC OFF switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (+) - 3 (E)
    Switch is pushed
    Below 1 Ω
    6 (+) - 3 (E)
    Switch is not pushed
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (VSC OFF Switch)



NG
REPLACE VSC OFF SWITCH (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)
  1. Disconnect the skid control ECU (brake booster with master cylinder assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A41-8 (CSW) - G76-6 (+)
    Always
    Below 1 Ω
    A41-8 (CSW) - Body ground
    Always
    10 kΩ or higher
    G76-3 (E) - Body ground
    Always
    Below 1 Ω


    Result:

    Result
    Proceed to
    OK (for LHD)
    A
    OK (for RHD)
    B
    NG
    C

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



B
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)  

7.INSPECT COMBINATION METER ASSEMBLY
  1. Turn the power switch off.

  1. Perform the Active Test of the combination meter assembly (meter CPU) using the intelligent tester (Click here).

  1. Check the combination meter assembly.

    OK:
    The multi-information display and VSC OFF indicator light turns on or off in accordance with intelligent tester operation.


    Result:

    Result
    Proceed to
    OK (for LHD)
    A
    OK (for RHD)
    B
    NG
    C

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



B
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)

C
INSPECT METER / GAUGE SYSTEM (Click here)
A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (Click here)