Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B1497/97    BUS IC Communication Malfunction

for Preparation Click here


DESCRIPTION

The air conditioning harness assembly connects the air conditioning amplifier assembly and the servo motors. The air conditioning amplifier assembly supplies power and sends operation instructions to each servo motor through the air conditioning harness assembly. Each servo motor sends damper position information to the air conditioning amplifier assembly.

DTC No.
DTC Detection Condition
Trouble Area
B1497/97
Error or open in communication line
  1. Air conditioning harness assembly
  2. No. 1 air conditioning radiator damper servo sub-assembly
  3. No. 2 air conditioning radiator damper servo sub-assembly
  4. No. 1 blower damper servo sub-assembly
  5. Air conditioning amplifier assembly

WIRING DIAGRAM


E233245E07


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Air Conditioner / Active test.

  1. Check the operation by referring to the table below.

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Air Mix Servo Targ Pulse(D)
    No. 1 air conditioning radiator damper servo sub-assembly (air mix) pulse
    Min.: 128, Max.: 383
    Operates between 173 and 257 pulses
    Air Outlet Servo Pulse (D)
    No. 2 air conditioning radiator damper servo sub-assembly (air outlet) pulse
    Min.: 128, Max.: 383
    Operates between 206 and 267 pulses
    Air Inlet Damper Targ Pulse
    No. 1 blower damper servo sub-assembly (air inlet) pulse
    Min.: 128, Max.: 383
    Operates between 254 and 287 pulses

    OK:
    Arm of the damper servo motor selected in the Active Test moves smoothly.

  1. According to the test result, proceed to the next step.

    Result:
    Result
    Proceed to
    One of the damper servo motors is malfunctioning
    A
    All of the damper servo motors are malfunctioning
    B



B
Go to step 6
A


2.SYSTEM CHECK
  1. According to the test result, proceed to the next step.

    Result:
    Result
    Proceed to
    Only the No. 1 air conditioning radiator damper servo sub-assembly (air mix) is malfunctioning
    A
    Only the No. 2 air conditioning radiator damper servo sub-assembly (air outlet) is malfunctioning
    B
    Only the No. 1 blower damper servo sub-assembly (air inlet) is malfunctioning
    C



B
Go to step 4

C
Go to step 5
A


3.REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR MIX)
  1. Replace the No. 1 air conditioning radiator damper servo sub-assembly (air mix) (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 6
A

END 

4.REPLACE NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR OUTLET)
  1. Replace the No. 2 air conditioning radiator damper servo sub-assembly (air outlet) (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 6
A

END 

5.REPLACE NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY (AIR INLET)
  1. Replace the No. 1 blower damper servo sub-assembly (air inlet) (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 6
A

END 

6.REPLACE AIR CONDITIONING HARNESS ASSEMBLY
  1. Replace the air conditioning harness assembly (Click here).

    HINT:
    Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1497/97 is not output
    A
    DTC B1497/97 is output
    B



B
Go to step 7
A

END 

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
  1. Disconnect the G34 air conditioning amplifier assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G34-21 (B) - Body ground
    Power switch off
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)