Home › Vehicle Interior › SEAT BELT › REAR SEAT OUTER BELT ASSEMBLY

REAR SEAT OUTER BELT ASSEMBLY > REMOVAL

for Preparation Click here



1. REMOVE REAR SEAT ASSEMBLY (for Separate Type Seatback)
(Click here)


2. REMOVE REAR SEAT ASSEMBLY (for Bench Type Seatback)
(Click here)


3. REMOVE REAR DOOR SCUFF PLATE


    B300785
  1. Disengage the 5 claws and guide and remove the rear door scuff plate LH.



4. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP
  1. Remove the rear door opening trim weatherstrip LH.



5. REMOVE DECK BOARD ASSEMBLY
  1. Remove the deck board assembly.



6. REMOVE DECK FLOOR BOX LH
  1. Remove the deck floor box LH.



7. REMOVE DECK FLOOR BOX RH

HINT:
Use the same procedure as for the LH side.



8. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
  1. Remove the package tray trim panel assembly.



9. REMOVE REAR DECK TRIM COVER


    B297727
  1. Remove the 2 clips.

  1. Disengage the 4 claws and 2 guides, and remove the rear deck trim cover.



10. DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY
  1. Remove the bolt.



    B307773
  1. Disengage the 2 claws and disconnect the floor anchor of the rear seat 3 point type outer belt assembly.



11. REMOVE REAR ABSORBER CAP


    B300796
  1. Disengage the 2 claws and 2 guides, and remove the rear absorber cap LH.



12. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (for LH Side)


    E286958E03
  1. Using a screwdriver with its tip wrapped with protective tape, disengage the claw.
    Text in Illustration 
    *a
    Protective Tape



    E286959
  1. Remove the No. 1 luggage compartment light assembly as shown in the illustration.

  1. Disconnect the connector and remove the No. 1 luggage compartment light assembly.



13. REMOVE DECK TRIM SIDE PANEL ASSEMBLY


  1. Turn the rear seatback hinge in the direction indicated by the arrow shown in the illustration.


    B300799E01


    Text in Illustration 
    *1
    Rear Seatback Hinge
    -
    -

  1. Remove the bolt and 2 screws.

  1. Disengage the 4 claws, 4 clips and guide, and remove the deck trim side panel assembly LH.



14. DISCONNECT REAR CENTER SEAT LAP TYPE BELT ASSEMBLY (for RH Side)


    B300537
  1. Using a moulding remover, disengage the 2 claws and open the cover.



    B297186
  1. Loosen the bolt and disconnect the shoulder anchor of the rear center seat lap type belt assembly.



15. REMOVE ROOF SIDE INNER GARNISH LH (for LH Side)


  1. Disengage the 5 clips.


    B299307

  1. Pass the floor anchor of the rear seat 3 point type outer belt assembly LH through the roof side inner garnish LH and remove the roof side inner garnish LH.



16. REMOVE ROOF SIDE INNER GARNISH RH (for RH Side)


    B299306
  1. Using a moulding remover, disengage the 4 claws and guide, and disconnect the belt guide.



  1. Disengage the 5 clips.


    B297735

  1. Pass the floor anchor of the rear seat 3 point type outer belt assembly RH through the roof side inner garnish RH and remove the roof side inner garnish RH.



17. REMOVE REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY


    B307774
  1. Remove the bolt and disconnect the shoulder anchor of the rear seat 3 point type outer belt assembly.



    B307775
  1. Remove the bolt.

  1. Disengage the 2 guides and remove the rear seat 3 point type outer belt assembly.