Home › Vehicle Interior › SEAT BELT › CHILD RESTRAINT SEAT ANCHOR BRACKET

CHILD RESTRAINT SEAT ANCHOR BRACKET > INSTALLATION

for Preparation Click here



1. INSTALL CROSS ANCHOR BRACKET SUB-ASSEMBLY (for Separate Type Seatback)


  1. Temporarily install the cross anchor bracket sub-assembly with the bolt shown in the illustration.


    B297197



  1. Install the 2 bolts and tighten the bolt in the order shown in the illustration.


    B297198E01

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



2. INSTALL CROSS ANCHOR BRACKET SUB-ASSEMBLY (for Bench Type Seatback)


  1. Temporarily install the cross anchor bracket sub-assembly with the bolt shown in the illustration.


    B297201



  1. Install the 2 bolts and tighten the bolt in the order shown in the illustration.


    B297200E01

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH


  1. Engage the guide, 4 claws and 4 clips.


    B300800E02


    Text in Illustration 
    *a
    Rear Seatback Hinge
    -
    -

  1. Install the deck trim side panel assembly LH with the bolt and 2 screws.

  1. Turn the rear seatback hinge as shown in the illustration.



4. INSTALL REAR ABSORBER CAP LH
  1. Engage the 2 guides and 2 claws to install the rear absorber cap LH.



5. INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY
  1. Connect the connector.



    E288706
  1. Engage the claw to install the No. 1 luggage compartment light assembly.



6. CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH
  1. Engage the 2 claws.

  1. Install the floor anchor of the rear seat 3 point type outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



7. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



8. INSTALL REAR ABSORBER CAP RH

HINT:
Use the same procedure as for the LH side.



9. CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



10. INSTALL REAR DECK TRIM COVER
  1. Engage the 2 guides and 4 claws.

  1. Install the rear deck trim cover with the 2 clips.



11. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY
  1. Install the package tray trim panel assembly.



12. INSTALL DECK FLOOR BOX LH
  1. Install the deck floor box LH.



13. INSTALL DECK FLOOR BOX RH

HINT:
Use the same procedure as for the LH side.



14. INSTALL DECK BOARD ASSEMBLY
  1. Install the deck board assembly.



15. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    B299875E01
  1. Align the alignment mark (White) on the weatherstrip with the flange on the vehicle body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
    Text in Illustration 
    *a
    Alignment Mark (White)
    *b
    Flange Position

    NOTICE:
    After installation, check that the corners fit correctly.



16. INSTALL REAR DOOR SCUFF PLATE LH
  1. Engage the guide and the 5 claws to install the rear door scuff plate.



17. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B299873E01
  1. Align the alignment mark (Red) on the weatherstrip with the flange on the vehicle body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.
    Text in Illustration 
    *a
    Alignment Mark (Red)
    *b
    Flange Position

    NOTICE:
    After installation, check that the corners fit correctly.



18. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side.



19. INSTALL REAR SEAT ASSEMBLY (for Separate Type Seatback)
(Click here)


20. INSTALL REAR SEAT ASSEMBLY (for Bench Type Seatback)
(Click here)