DTC U0100 Lost Communication with ECM / PCM "A" |
DTC U0129 Lost Communication with Brake System Control Module |
DTC U0293 Lost Communication with HV ECU |
| DTC No. | DTC Detection Condition | Trouble Area |
| U0100 | The hybrid vehicle control computer assembly does not receive data from the ECM. |
|
| U0129 | The hybrid vehicle control computer assembly does not receive data from the brake booster with master cylinder assembly (skid control ECU). |
|
| U0293 |
|
|

| 1.RECONFIRM DTC OUTPUT |
Reconfirm DTCs.
| Result | Proceed to |
| The hybrid vehicle control computer assembly outputs DTC U0129 and other DTCs. (GTS display: Hybrid Control) | A |
| The hybrid vehicle control computer assembly outputs only DTC U0129. (GTS display: Hybrid Control) | B |
|
| ||||
| A | |
| 2.CHECK SUB BUS 15 |
Disconnect the cable from the negative (-) auxiliary battery terminal.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
| G81-31 (CA3P) - G81-30 (CA3N) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω | Below 54 Ω: Short circuit between bus lines |
| 70 Ω or higher: Open circuit in main bus lines | |||
| G81-31 (CA3P) - G80-6 (E1) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short |
| G81-30 (CA3N) - G80-6 (E1) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short |
| G81-31 (CA3P) - G81-3 (BATT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| G81-30 (CA3N) - G81-3 (BATT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| *a | Component with harness connected (Hybrid Vehicle Control Computer Assembly) |
| Result | Proceed to |
| OK | A |
| NG (Open circuit in CAN main bus lines) | B |
| NG (Short circuit between bus lines) | C |
| D |
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||
| 3.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY) |
![]() |
Disconnect the G81 hybrid vehicle control computer assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G81-31 (CA3P) - G81-30 (CA3N) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Rear view of wire harness connector (to Hybrid Vehicle Control Computer Assembly) |
|
| ||||
| OK | ||
| ||
| 4.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (CAN J/C LH) |
Reconnect the G81 hybrid vehicle control computer assembly connector.
![]() |
Disconnect the G71 CAN junction connector LH (instrument panel wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
| G71-10 (CANH) - G71-21 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | Hybrid vehicle control computer assembly |
| *a | Front view of wire harness connector (to CAN Junction Connector LH (Instrument Panel Wire Side)) |
| *b | to Hybrid Vehicle Control Computer Assembly |
|
| ||||
| OK | |
| 5.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (CAN J/C LH) |
Reconnect the G71 CAN junction connector LH (instrument panel wire side).
![]() |
Disconnect the A51 CAN junction connector LH (engine room main wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
| A51-3 (CANH) - A51-14 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | ECM |
| *a | Front view of wire harness connector (to CAN Junction Connector LH (Engine Room Main Wire Side)) |
| *b | to ECM |
|
| ||||
| OK | ||
| ||
| 6.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (ECM - CAN J/C LH) |
Reconnect the A51 CAN junction connector LH (engine room main wire side).
![]() |
Disconnect the A40 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A40-12 (CANP) - A40-25 (CANN) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector (to ECM) |
|
| ||||
| OK | ||
| ||
| 7.CHECK FOR SHORT IN SUB BUS 15 LINES (HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY - CAN J/C LH) |
![]() |
Disconnect the G81 hybrid vehicle control computer assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G81-31 (CA3P) - G81-30 (CA3N) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Rear view of wire harness connector (to Hybrid Vehicle Control Computer Assembly) |
|
| ||||
| OK | ||
| ||
| 8.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN J/C LH) |
Reconnect the G81 hybrid vehicle control computer assembly connector.
![]() |
Disconnect the G71 CAN junction connector LH (instrument panel wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
| G71-10 (CANH) - G71-21 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | Hybrid vehicle control computer assembly |
| *a | Front view of wire harness connector (to CAN Junction Connector LH (Instrument Panel Wire Side)) |
| *b | to Hybrid Vehicle Control Computer Assembly |
|
| ||||
| OK | |
| 9.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN J/C LH) |
Reconnect the G71 CAN junction connector LH (instrument panel wire side).
![]() |
Disconnect the A51 CAN junction connector LH (engine room main wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
| A51-1 (CANH) - A51-12 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Brake booster with master cylinder assembly (Skid control ECU) |
| A51-3 (CANH) - A51-14 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | ECM |
| *a | Front view of wire harness connector (to CAN Junction Connector LH (Engine Room Main Wire Side)) |
| *b | to Brake Booster with Master Cylinder Assembly (Skid Control ECU) |
| *c | to ECM |
| Result | Proceed to |
| OK | A |
| NG (ECM CAN main bus lines) | B |
| NG (Brake booster with master cylinder assembly (Skid control ECU) CAN branch lines) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 10.CHECK FOR SHORT IN SUB BUS 15 LINES (ECM - CAN J/C LH) |
Reconnect the A51 CAN junction connector LH (engine room main wire side).
![]() |
Disconnect the A40 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A40-12 (CANP) - A40-25 (CANN) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector (to ECM) |
|
| ||||
| OK | ||
| ||
| 11.CHECK FOR SHORT IN SUB BUS 15 LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - CAN J/C LH) |
Reconnect the A51 CAN junction connector LH (engine room main wire side).
![]() |
Disconnect the A41 brake booster with master cylinder assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A41-35 (CA2H) - A41-34 (CA2L) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| *a | Front view of wire harness connector (to Brake Booster with Master Cylinder Assembly (Skid Control ECU)) |
| Result | Proceed to |
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 12.CHECK FOR SHORT IN SUB BUS 15 LINE (CAN J/C LH) |
![]() |
Disconnect the G71 CAN junction connector LH (instrument panel wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
| G71-10 (CANH) - G4-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Hybrid vehicle control computer assembly |
| G71-21 (CANL) - G4-4 (CG) | |||
| G71-10 (CANH) - G4-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Hybrid vehicle control computer assembly |
| G71-21 (CANL) - G4-16 (BAT) |
| *1 | DLC3 |
| *a | Front view of wire harness connector (to CAN Junction Connector LH (Instrument Panel Wire Side)) |
| *b | to Hybrid Vehicle Control Computer Assembly |
|
| ||||
| OK | |
| 13.CHECK FOR SHORT IN SUB BUS 15 LINE (CAN J/C LH) |
![]() |
Disconnect the A51 CAN junction connector LH (engine room main wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
| A51-1 (CANH) - G4-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Brake booster with master cylinder assembly (Skid control ECU) |
| A51-12 (CANL) - G4-4 (CG) | |||
| A51-3 (CANH) - G4-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | ECM |
| A51-14 (CANL) - G4-4 (CG) | |||
| A51-1 (CANH) - G4-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Brake booster with master cylinder assembly (Skid control ECU) |
| A51-12 (CANL) - G4-16 (BAT) | |||
| A51-3 (CANH) - G4-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | ECM |
| A51-14 (CANL) - G4-16 (BAT) |
| *1 | DLC3 |
| *a | Front view of wire harness connector (to CAN Junction Connector LH (Engine Room Main Wire Side)) |
| *b | to Brake Booster with Master Cylinder Assembly (Skid Control ECU) |
| *c | to ECM |
| Result | Proceed to |
| OK | A |
| NG (ECM CAN main bus line) | B |
| NG (Brake booster with master cylinder assembly (Skid control ECU) CAN branch line) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 14.CHECK FOR SHORT IN SUB BUS 15 LINE (HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY - CAN J/C LH) |
![]() |
Disconnect the G80 and G81 hybrid vehicle control computer assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G81-31 (CA3P) - G80-6 (E1) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| G81-30 (CA3N) - G80-6 (E1) | ||
| G81-31 (CA3P) - G81-3 (BATT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| G81-30 (CA3N) - G81-3 (BATT) |
| *a | Rear view of wire harness connector (to Hybrid Vehicle Control Computer Assembly) |
|
| ||||
| OK | ||
| ||
| 15.CHECK FOR SHORT IN SUB BUS 15 LINE (ECM - CAN J/C LH) |
![]() |
Disconnect the A40 and C9 or C10 ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A40-12 (CANP) - C9-16 (E1)*1 A40-12 (CANP) - C10-16 (E1)*2 | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A40-25 (CANN) - C9-16 (E1)*1 A40-25 (CANN) - C10-16 (E1)*2 | ||
| A40-12 (CANP) - A40-1 (BATT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A40-25 (CANN) - A40-1 (BATT) |
| *A | for RHD |
| *B | for LHD |
| *a | Front view of wire harness connector (to ECM) |
|
| ||||
| OK | ||
| ||
| 16.CHECK FOR SHORT IN SUB BUS 15 LINE (BRAKE BOOSTER WITH MASTER CYLINDER - CAN J/C LH) |
![]() |
Disconnect the A41 brake booster with master cylinder assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A41-35 (CA2H) - A41-28 (GND) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A41-34 (CA2L) - A41-28 (GND) | ||
| A41-35 (CA2H) - A41-14 (BI) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A41-34 (CA2L) - A41-14 (BI) |
| *a | Front view of wire harness connector (to Brake Booster with Master Cylinder Assembly (Skid Control ECU)) |
| Result | Proceed to |
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
|
| ||||
|
| ||||
| A | ||
| ||