Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

DTC    U0129    Lost Communication with Brake System Control Module

for Preparation Click here


DESCRIPTION


DTC No.
DTC Detection Condition
Trouble Area
U0129
No communication from the brake booster with master cylinder assembly (skid control ECU) continues.
  1. Brake booster with master cylinder assembly (Skid control ECU) branch line or connector
  2. Power source circuit of brake booster with master cylinder assembly (skid control ECU)
  3. Brake booster with master cylinder assembly (Skid control ECU) ground circuit
  4. Brake booster with master cylinder assembly (Skid control ECU)

HINT:
This diagnosis procedure is for when DTC U0129 is output only by the hybrid vehicle control computer assembly (GTS display: Hybrid Control).


WIRING DIAGRAM


C244195E19


INSPECTION PROCEDURE

NOTICE:
  1. Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  2. After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).
  3. Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click here).
  4. After the repair, perform CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (Click here).
  5. Inspect the fuses for circuits related to this system before performing the following procedure.

HINT:
  1. Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

1.RECONFIRM DTC OUTPUT
  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

OK:
DTC C1241 is not output.



NG
GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC (Click here)
OK


2.RECONFIRM DTC OUTPUT
  1. Reconfirm DTCs.

HINT:
If the hybrid vehicle control computer assembly outputs DTC U0100 and DTC U0129, check the branch circuit of sub bus 15.

Result:
Result
Proceed to
The hybrid vehicle control computer assembly outputs only DTC U0129.
(GTS display: Hybrid Control)
A
The hybrid vehicle control computer assembly outputs DTC U0100 and U0129.
(GTS display: Hybrid Control)
B



B
GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC (Click here)
A


3.CHECK FOR OPEN IN CAN BUS LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY BRANCH LINE)
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



    C249762E45
  1. Disconnect the A41 brake booster with master cylinder assembly (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A41-35 (CA2H) - A41-34 (CA2L)
    Cable disconnected from negative (-) auxiliary battery terminal
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Brake Booster with Master Cylinder Assembly (Skid Control ECU))

    Result:
    Result
    Proceed to
    OK (for LHD)
    A
    OK (for RHD)
    B
    NG
    C



B
REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (for RHD) (Click here)

C
REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)
A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (for LHD) (Click here)