Home › Engine / Hybrid System › 1NZ-FXE ENGINE CONTROL › IGNITION SYSTEM

IGNITION SYSTEM > ON-VEHICLE INSPECTION

for Preparation Click here



1. PERFORM SPARK TEST
  1. Check for DTCs (Click here).

    NOTICE:
    If any DTC is output, perform troubleshooting procedures for that DTC.

  1. Remove the ignition coil assemblies and spark plugs (Click here).



    A267418
  1. Disconnect the 4 injector connectors.

  1. Set the vehicle to inspection mode (Click here).(Step 3)

  1. Install the spark plug into the ignition coil assembly, and then connect the ignition coil connector. (Step 4)



    A267421
  1. Ground the spark plug. (Step 5)

  1. Check that spark occurs at each spark plug while the engine is being cranked. (Step 6)

    NOTICE:
    1. Be sure to ground the spark plugs when checking them.
    2. Do not crank the engine for more than 2 seconds.
      Cranking will stop if the power switch is pushed again for models with cranking holding function.
    3. If a spark plug has been struck or dropped, replace it.
    4. If an ignition coil assembly has been struck or dropped, replace it.

    HINT:
    1. Repeat steps 3 to 6 for each spark plug and ignition coil assembly.
    2. If spark does not occur for any cylinder, perform the following Inspect Ignition Coil and Spark Test procedure.



    A267418
  1. Connect the 4 fuel injector connectors.

  1. Install the spark plugs and ignition coil assemblies (Click here).

  1. Check for DTCs (Click here).

  1. Clear the DTCs (Click here).



2. INSPECT IGNITION COIL AND SPARK TEST

HINT:
Perform "Inspection After Repair" after replacing the spark plug and ignition coil assembly (Click here).

  1. Check that the wire harness side connector of the ignition coil assembly is securely connected.
    Result 
    Result
    Action
    NG
    Connect securely
    OK
    Go to next step

  1. Perform a spark test on each ignition coil assembly.

    1. Replace the ignition coil assembly with a known good one.

    2. Set the vehicle to inspection mode (Click here).

    3. Perform the spark test again.
      Result 
      Result
      Action
      NG
      Go to next step
      OK
      Replace ignition coil assembly

  1. Perform a spark test on each spark plug.

    1. Replace the spark plug with a known good one.

    2. Set the vehicle to inspection mode (Click here).

    3. Perform the spark test again.
      Result 
      Result
      Action
      NG
      Inspect the ignition system (Click here).
      OK
      Replace spark plug

      NOTICE:
      1. If the ignition coil assembly has been struck or dropped, replace it.
      2. If the spark plug has been struck or dropped, replace it.



3. CHECK SPARK PLUG

NOTICE:
  1. Do not use a wire brush for cleaning.
  2. Do not adjust the electrode gap of a used spark plug.

HINT:
Perform "Inspection After Repair" after replacing the spark plug (Click here).



    I039522E41
  1. Check the electrode using a megohmmeter:
    Text in Illustration 
    *a
    Ground

    1. Using a megohmmeter, measure the insulation resistance.

      Standard Insulation Resistance:
      Tester Connection
      Condition
      Specified Condition
      Spark plug (terminal part) - Body ground
      Always
      10 MΩ or higher

      HINT:
      1. If the result is not as specified, clean the spark plug with a spark plug cleaner and measure the resistance again.
      2. If a megohmmeter is not available, perform the following simple inspection instead.



    A126881
  1. Alternative inspection method:

    1. Quickly accelerate the engine to 2500 rpm 5 times.

    2. Remove the spark plug (Click here).

    3. Visually check the spark plug.
      If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.

  1. Check the spark plug for any damage to its thread and insulator.
    If there is any damage, replace the spark plug.

    Recommended Spark Plug:
    Manufacturer
    Spark Plug Type
    DENSO
    FK16R-A8



  1. Reference:



      A260264E03
    1. Check the spark plug electrode gap.

      Maximum electrode gap for a used spark plug:
      1.1 mm (0.0433 in.)

      If the gap is more than the maximum, replace the spark plug.

      NOTICE:
      Never attempt to adjust the gap of a used plug.

      Electrode gap for a new spark plug:
      0.7 to 0.8 mm (0.0276 to 0.0315 in.)

      Text in Illustration 
      *a
      Spark plug electrode gap



    B062019E01
  1. Clean the spark plugs.
    If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

    Standard air pressure:
    588 kPa (6.0 kgf/cm2, 85 psi)

    Standard duration:
    20 seconds or less

    HINT:
    Only use a spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.

  1. Install the spark plug (Click here).