Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Power Steering ECU Communication Stop Mode

for Preparation Click here


DESCRIPTION


Detection Item
Symptom
Trouble Area
Power Steering ECU Communication Stop Mode
Either condition is met:
  1. "Power Steering (EPS)" is not displayed on the CAN Bus Check screen of the GTS (Click here)
  2. Communication system DTCs (DTCs that start with U) that correspond to "Power Steering ECU Communication Stop Mode" in "DTC Combination Table" are output (Click here)
  1. Power steering ECU assembly branch line or connector
  2. Power source circuit of power steering ECU assembly
  3. Power steering ECU assembly ground circuit
  4. Power steering ECU assembly

WIRING DIAGRAM


C349991E01


C251624E06


INSPECTION PROCEDURE

NOTICE:
  1. Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  2. After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).
  3. Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click here).
  4. After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
  5. DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control main switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more.
  6. After the repair, perform the CAN bus check that all the ECUs and sensors connected to the CAN communication system are displayed (Click here).
  7. Inspect the fuses for circuits related to this system before performing the following procedure.

HINT:
  1. Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

1.CHECK FOR OPEN IN CAN BUS LINES (POWER STEERING ECU ASSEMBLY BRANCH LINE)
  1. Disconnect the cable from the negative (-) auxiliary battery terminal.



    C251167E01
  1. Disconnect the G6 power steering ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G6-7 (CANH) - G6-8 (CANL)
    Cable disconnected from negative (-) auxiliary battery terminal
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Steering ECU Assembly)



NG
REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (POWER STEERING ECU ASSEMBLY)
OK


2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)


    C240535E09
  1. Disconnect the A33 power steering ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A33-2 (PGND) - Body ground
    Cable disconnected from negative (-) auxiliary battery terminal
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Steering ECU Assembly)

  1. Reconnect the cable to the negative (-) auxiliary battery terminal.



    C251167E02
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G6-1 (IG) - Body ground
    Power switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Steering ECU Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK

REPLACE POWER STEERING ECU ASSEMBLY (Click here)