DTC B2799 Engine Immobiliser System Malfunction |
| DTC Code | DTC Detection Condition | Trouble Area | DTC Output Confirmation Operation |
| B2799 | Either condition is met (1 trip detection logic*):
|
| Either condition is met:
|
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
| Hybrid control system cannot be started | - |
| DTC Code | Data List and Active Test |
| B2799 | - |

| 1.CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 2.CHECK FOR DTC |
Start the hybrid control system.
Wait 10 seconds or more.
Check for DTCs (Click here).
| Result | Proceed to |
| OK | A |
| NG (DTC B2799 is output) | B |
| NG (Other DTCs are output) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 3.INSPECT EV CONTROL ECU (TERMINAL IMO) |
Using an oscilloscope, check the waveform.

| *a | Component with harness connected (Hybrid Vehicle Control ECU) | *b | Waveform |
| Item | Content |
| Tester Connection | G81-23 (IMO) - Body ground |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds after hybrid control system starts, or within 3 seconds after power switch first turned to on (IG) after auxiliary battery disconnected and reconnected |
| Result | Proceed to |
| Normal waveform | A |
| Terminal IMO stuck low (2.4 V or less) | B |
| Terminal IMO stuck high (12 V) or Abnormal waveform | C |
|
| ||||
|
| ||||
| A | |
| 4.INSPECT EV CONTROL ECU (TERMINAL IMI) |
Using an oscilloscope, check the waveform.

| *a | Component with harness connected (Hybrid Vehicle Control ECU) | *b | Waveform |
| Item | Content |
| Tester Connection | G81-22 (IMI) - Body ground |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds after hybrid control system starts, or within 3 seconds after power switch first turned to on (IG) after auxiliary battery disconnected and reconnected |
| Result | Proceed to |
| Normal waveform | A |
| Not output waveform or abnormal waveform | B |
|
| ||||
| A | |
| 5.REGISTER ECU COMMUNICATION ID |
Reregister the ECU communication ID.
| NEXT | |
| 6.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS |
Check that the hybrid control system starts with an already registered vehicle key.
|
| ||||
| OK | ||
| ||
| 7.INSPECT EV CONTROL ECU (IMO TERMINAL VOLTAGE) |
![]() |
Disconnect the G81 hybrid vehicle control ECU connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Result | Proceed to |
| Terminal IMO stuck low (2.4 V or less) | A |
| Terminal IMO stuck high (12 V) | B |
| *a | Rear view of wire harness connector (to Hybrid Vehicle Control ECU) |
|
| ||||
| A | |
| 8.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - ID CODE BOX AND BODY GROUND) |
Disconnect the G49 ID code box (immobiliser code ECU) connector.
Disconnect the G81 hybrid vehicle control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| G49-3 (EFII) - G81-23 (IMO) | Always | Below 1 Ω |
| G81-23 (IMO) - Body ground | Always | 10 kΩ or higher |
| G49-4 (EFIO) - G81-22 (IMI) | Always | Below 1 Ω |
| G81-22 (IMI) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 9.REPLACE ID CODE BOX (IMMOBILISER CODE ECU) |
Replace the ID code box (immobiliser code ECU).
| NEXT | |
| 10.REGISTER ECU COMMUNICATION ID |
Reregister the ECU communication ID.
| NEXT | |
| 11.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS |
Check that the hybrid control system starts with an already registered vehicle key.
|
| ||||
| OK | ||
| ||
| 12.REPLACE EV CONTROL ECU |
Temporarily replace the hybrid vehicle control ECU with a new one (Click here).
| NEXT | |
| 13.REGISTER ECU COMMUNICATION ID |
Reregister the ECU communication ID.
| NEXT | |
| 14.CHECK WHETHER HYBRID CONTROL SYSTEM STARTS |
Check that the hybrid control system starts with an already registered vehicle key.
|
| ||||
| OK | ||
| ||