AIR CONDITIONING UNIT > REMOVAL |
| 1. PRECAUTION |
| 2. RECOVER REFRIGERANT FROM AIR CONDITIONING SYSTEM |
Start the hybrid system.
Operate the cooler compressor under the conditions show below:
| Item | Condition |
| Engine Speed | Idling |
| Operating Time | 3 minutes or more |
| A/C Switch Status | ON |
| Blower Switch Status | HI |
| Set Temperature | MAX COOL |
Stop the engine.
Recover the refrigerant from the A/C system using a refrigerant recovery unit.
| 3. REMOVE WINDSHIELD WIPER MOTOR AND LINK |
| 4. REMOVE INNER COWL TOP TO COWL BRACE (for LHD) |
![]() |
Remove the 3 bolts and inner cowl top to cowl brace.
| 5. REMOVE INNER COWL TOP TO COWL BRACE (for RHD) |
![]() |
Remove the 3 bolts and inner cowl top to cowl brace.
| 6. REMOVE FRONT AIR SHUTTER SEAL (for LHD) |
![]() |
Disengage the clamp to remove the front air shutter seal.
| 7. REMOVE FRONT AIR SHUTTER SEAL (for RHD) |
![]() |
Disengage the clamp to remove the front air shutter seal.
| 8. REMOVE FRONT NO. 1 VENTILATOR SEAL (for LHD) |
![]() |
Disengage the clamp to remove the front No. 1 ventilator seal.
| 9. REMOVE FRONT NO. 1 VENTILATOR SEAL (for RHD) |
![]() |
Disengage the clamp to remove the front No. 1 ventilator seal.
| 10. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD) |
![]() |
Disengage the clamp to separate the wire harness from the outer cowl top panel sub-assembly.
![]() |
Remove the 8 bolts, nut and outer cowl top panel sub-assembly.
| 11. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD) |
![]() |
Disengage the 3 clamps to separate the wire harness from the outer cowl top panel sub-assembly.
![]() |
Remove the 8 bolts, nut and outer cowl top panel sub-assembly.
| 12. DISCONNECT SUCTION PIPE SUB-ASSEMBLY |
![]() |
Remove the bolt and rotate the hook connector.
![]() |
Disconnect the suction pipe sub-assembly.
Remove the O-ring from the suction pipe sub-assembly.
| 13. DISCONNECT LIQUID PIPE SUB-ASSEMBLY |
![]() |
Disconnect the liquid pipe sub-assembly.
Remove the O-ring from the liquid pipe sub-assembly.
| 14. DISCONNECT HEATER WATER OUTLET HOSE A |
![]() |
Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water outlet hose A.
| 15. DISCONNECT WATER HOSE SUB-ASSEMBLY |
![]() |
Using pliers, grip the claws of the clip and slide the clip to disconnect the water hose sub-assembly.
| 16. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
| 17. REMOVE STEERING COLUMN ASSEMBLY |
| 18. REMOVE HYBRID VEHICLE CONTROL ECU |
![]() |
Disconnect the 4 hybrid vehicle control ECU connectors.
| *A | for LHD |
| *B | for RHD |
![]() |
Remove the 2 nuts and hybrid vehicle control ECU.
| *A | for LHD |
| *B | for RHD |
| 19. DISCONNECT INSTRUMENT PANEL WIRE |
Remove the bolt.

| *A | for LHD: | *B | for RHD: |
Disengage the 2 clamps and disconnect the instrument panel wire.
| 20. REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (for LHD) |
![]() |
Disengage the clamp.
Disconnect the connector (A).
Disengage the 2 claws and disconnect the 2 connectors (B).
![]() |
Remove the 2 bolts.
Disengage the 2 clamps and pull out the instrument panel junction block assembly.
![]() |
Disengage the claw and disconnect the connector as shown in the illustration.
![]() |
Disengage the claw and release the connector lock as shown in the illustration.
![]() |
Disengage the claw and disconnect the connector as shown in the illustration to remove the instrument panel junction block assembly.
| 21. REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (for RHD) |
for Halogen Headlight:
![]() |
Disconnect the 2 connectors (A).
| *A | for Halogen Headlight: |
| *B | for LED Headlight: |
for LED Headlight:
Disconnect the 3 connectors (A).
Disengage the 2 claws and disconnect the 2 connectors (B).
Disengage the clamp.
![]() |
Remove the 2 bolts.
Disengage the 2 clamps and pull out the instrument panel junction block assembly.
![]() |
Disengage the claw and disconnect the connector as shown in the illustration.
![]() |
Disengage the claw and release the connector lock as shown in the illustration.
![]() |
Disengage the claw and disconnect the connector as shown in the illustration to remove the instrument panel junction block assembly.
| 22. REMOVE POWER STEERING ECU ASSEMBLY (for LHD) |
![]() |
Disconnect the 4 connectors from the power steering ECU assembly.
![]() |
Remove the 2 nuts and power steering ECU assembly.
| 23. REMOVE POWER STEERING ECU ASSEMBLY (for RHD) |
![]() |
Disconnect the 4 connectors from the power steering ECU assembly.
![]() |
Remove the 2 nuts and power steering ECU assembly.
| 24. REMOVE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY |
![]() |
Disconnect the connector.
Disengage the clamp and remove the No. 1 indoor electrical key antenna assembly.
| 25. REMOVE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY |
![]() |
Disconnect the connector.
Disengage the clamp and remove the No. 2 indoor electrical key antenna assembly.
| 26. DISCONNECT FRONT FLOOR CARPET ASSEMBLY |
Turn back the front floor carpet assembly.
| 27. REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY (for LHD) |
![]() |
Disengage each clamp.
| *1 | Bolt |
| *2 | Screw |
| *3 | Nut |
Remove the 2 bolts, screw, nut and No. 1 instrument panel brace sub-assembly.
| 28. REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY (for RHD) |
![]() |
Disengage each clamp.
| *1 | Bolt |
| *2 | Screw |
| *3 | Nut |
Remove the bolt, screw, nut and No. 1 instrument panel brace sub-assembly.
| 29. DISCONNECT INSTRUMENT PANEL WIRE (for LHD) |
![]() |
for LH Side:
Disconnect each connector.
![]() |
Disconnect the connector from the connector holder.
Remove the bolt.
Disengage each clamp and disconnect the connector holder.
![]() |
for RH Side:
Disconnect each connector.
![]() |
Remove the bolt.
Disengage each clamp and disconnect the connector holder.
Remove the 2 bolts <A> and disconnect the 2 earth wires.

| *1 | Earth Wire | *2 | Bolt <A> |
| *3 | Bolt <B> | - | - |
Remove the bolt <B>.
Disconnect the connector.
Disengage each clamp.
Remove the bolt and disconnect the earth wire.

| *1 | Earth Wire | - | - |
Disconnect the connector.
Disengage each clamp and disconnect the instrument panel wire.
| 30. DISCONNECT INSTRUMENT PANEL WIRE (for RHD) |
![]() |
for RH Side:
Disconnect each connector.
![]() |
Disconnect the connector from the connector holder.
Remove the bolt.
Disengage each clamp and disconnect the connector holder.
![]() |
for LH Side:
Disconnect each connector.
![]() |
Remove the bolt.
Disengage each clamp and disconnect the connector holder.
Remove the 2 bolts and disconnect the 2 earth wires.

| *1 | Earth Wire | - | - |
Disconnect each connector.
Disengage each clamp.
Remove the bolt <A> and disconnect the earth wire.

| *1 | Earth Wire | *2 | Bolt <A> |
| *3 | Bolt <B> | - | - |
Remove the bolt <B>.
Disconnect the connector.
Disengage each clamp and disconnect the instrument panel wire.
| 31. REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY |
Remove the 8 bolts and 3 screws, and remove the instrument panel reinforcement.

| *1 | Bolt | *2 | Screw |
| 32. REMOVE DEFROSTER NOZZLE ASSEMBLY |
![]() |
Disengage the 2 claws and 3 guides and remove the defroster nozzle assembly.
| 33. DISCONNECT DRAIN COOLER HOSE |
![]() |
Disconnect the drain cooler hose.
| 34. REMOVE AIR CONDITIONER UNIT ASSEMBLY |
Remove the 3 bolts and nut, and remove the air conditioner unit assembly.

| 35. REMOVE AIR CONDITIONING RADIATOR ASSEMBLY (for LHD) |
Disconnect the connector.

Remove the 3 screws and air conditioning radiator assembly.
| 36. REMOVE AIR CONDITIONING RADIATOR ASSEMBLY (for RHD) |
Disconnect the connector.

Remove the 3 screws and air conditioning radiator assembly.
| 37. REMOVE ASPIRATOR |
![]() |
Disengage the 2 claws and remove the aspirator.
| 38. REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY |
![]() |
Disconnect the connector.
Remove the screw.
Remove the air conditioning amplifier assembly as shown in the illustration.

| 39. REMOVE AIR CONDITIONING HARNESS ASSEMBLY (for LHD) |
Disengage each clamp.

Disconnect each connector and remove the air conditioning harness assembly.
| 40. REMOVE AIR CONDITIONING HARNESS ASSEMBLY (for RHD) |
Disengage each clamp.

Disconnect each connector and remove the air conditioning harness assembly.
| 41. REMOVE NO. 3 AIR DUCT SUB-ASSEMBLY |
![]() |
Disengage the 3 claws and remove the No. 3 air duct sub-assembly.
| 42. REMOVE NO. 2 AIR DUCT SUB-ASSEMBLY |
![]() |
Disengage the 3 claws and remove the No. 2 air duct sub-assembly.