Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY

STEERING COLUMN ASSEMBLY > REMOVAL

for Preparation Click here



1. PRECAUTION
(Click here)


2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD


3. REMOVE HORN BUTTON ASSEMBLY
(Click here)


4. REMOVE STEERING WHEEL ASSEMBLY


    C252595E01
  1. Remove the steering wheel assembly set nut.
    Text in Illustration 
    *a
    Matchmark

  1. Put matchmarks on the steering wheel assembly and steering main shaft.

  1. Disconnect the connectors from the spiral cable.



    C252596E01
  1. Using SST, remove the steering wheel assembly.
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05070)

    NOTICE:
    Apply a small amount of grease to the threads and tip of SST (09953-05020) before use.



5. REMOVE LOWER STEERING COLUMN COVER


    C248042
  1. Remove the 3 screws.



    C256915
  1. Disengage the 4 claws and remove the lower steering column cover.



6. REMOVE UPPER STEERING COLUMN COVER


    C248044
  1. Disengage the 2 claws and remove the upper steering column cover.



7. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
  1. Do not replace the spiral cable with sensor sub-assembly with the negative (-) auxiliary battery cable connected and the power switch on (IG).
  2. Do not rotate the spiral cable with sensor sub-assembly without the steering wheel with the negative (-) auxiliary battery cable connected and the power switch on (IG).
  3. Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.
  4. Do not remove the spiral cable from the steering sensor.

  1. Disconnect the connectors from the turn signal switch assembly with spiral cable sub-assembly.



    C248045E01
  1. Using pliers, expand the clamp.
    Text in Illustration 
    *1
    Clamp
    *2
    Claw

  1. While holding the clamp expanded, raise the claw using a screwdriver to disengage it, and then remove the turn signal switch assembly with spiral cable sub-assembly from the steering column assembly.



8. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIR BAG ASSEMBLY
(Click here)


9. REMOVE COLUMN HOLE COVER SILENCER SHEET


    C248046
  1. Remove the 2 clips and the column hole cover silencer sheet.



10. SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY


    C249572E01
  1. Put matchmarks on the steering sliding yoke sub-assembly and steering gear assembly.
    Text in Illustration 
    *a
    Matchmark

  1. Loosen bolt A.

  1. Remove bolt B.

  1. Separate the steering sliding yoke sub-assembly from the steering gear assembly.



11. REMOVE STEERING SLIDING YOKE SUB-ASSEMBLY


    C232525E01
  1. Put matchmarks on the steering sliding yoke sub-assembly and No. 2 steering intermediate shaft assembly.
    Text in Illustration 
    *a
    Matchmark

  1. Remove the steering sliding yoke sub-assembly from the No. 2 steering intermediate shaft assembly.



12. REMOVE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY


    C252587E01
  1. Put matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly.
    Text in Illustration 
    *a
    Matchmark

  1. Remove the bolt.

  1. Remove the steering intermediate shaft assembly from the steering column assembly.



13. REMOVE BRAKE PEDAL SUPPORT ASSEMBLY
  1. for LHD: (Click here)
  2. for RHD: (Click here)


14. REMOVE UPPER INSTRUMENT PANEL ASSEMBLY
(Click here)


15. REMOVE STEERING COLUMN ASSEMBLY


    C248047
  1. Disconnect the 2 connectors from the power steering ECU assembly.

  1. Disengage the wire harness clamp.

  1. Disconnect the connectors and disengage the wire harness clamps from the steering column assembly.



    C252588
  1. Remove the bolt, 2 nuts and steering column assembly.