Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR

BACK DOOR > REASSEMBLY

for Preparation Click here



1. INSTALL BACK DOOR STAY BOLT LH
  1. Clean the threaded portion on the vehicle body with a non-residue solvent.

  1. Clean the threaded portion on the vehicle body with a non-residue solvent.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the back door stay bolt.

    Torque:
    22 N*m{ 224 kgf*cm , 16 ft.*lbf }



2. INSTALL BACK DOOR STAY BOLT RH

HINT:
Use the same procedure as for the LH side.



3. INSTALL BACK DOOR DAMPER STAY UPPER BRACKET LH
  1. Clean the threaded portion on the vehicle body with a non-residue solvent.

  1. Apply adhesive to the threads of the 2 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the back door upper damper stay bracket with the 2 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



4. INSTALL BACK DOOR DAMPER STAY UPPER BRACKET RH

HINT:
Use the same procedure as for the LH side.



5. INSTALL BACK DOOR STAY ASSEMBLY LH

NOTICE:
  1. Avoid touching the stroke portions of the rod as much as possible to prevent foreign matter from attaching to the stroke portions. Be sure to hold the cylinders while servicing.
  2. Do not wear cotton gloves or other similar materials when handling the rod. Fibers may attach to the rod and result in gas leaks.
  3. Do not apply any load to the cylinders in the horizontal direction, in order to prevent the rod from being deformed.



  1. When reusing the back door stay assembly:



      B299127
    1. Install the 2 stop rings to the back door stay assembly.



    B297015
  1. Install the back door stay assembly.

    NOTICE:
    Install the back door stay assembly while supporting the back door by hand.

  1. Check that the back door stay assembly is engaged in the ball joint and that the back door stay assembly cannot be pulled out.



6. INSTALL BACK DOOR STAY ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



7. INSTALL REAR WIPER MOTOR ASSEMBLY
(Click here)


8. INSTALL REAR WASHER NOZZLE
  1. Engage the 2 claws to install the rear washer nozzle.

  1. Connect the washer hose.



9. INSPECT REAR WASHER NOZZLE


  1. Operate the rear washer nozzle and check the position that the washer fluid hits the windshield.

    Standard:
    Washer fluid hits the windshield in the area shown in the illustration.



    E246656E01


    Text in Illustration 
    *a
    Measurement
    -
    -

    Standard Clearance:

    Area
    Measurement
    Area
    Measurement
    A
    138.4 mm (5.45 in.)
    B
    130.7 mm (5.15 in.)
    C
    60.3 mm (2.37 in.)
    D
    191 mm (7.52 in.)



10. ADJUST REAR WASHER NOZZLE


    E237619
  1. Using a screwdriver, adjust the direction of the rear washer nozzle.

    NOTICE:
    Do not use a safety pin or other pointed tools. Doing so may damage the inside of the washer nozzle.

    HINT:
    Use a thin-bladed screwdriver with an approximately 1 mm (0.0394 in.) thick tip.



11. INSTALL REAR SPOILER ASSEMBLY
(Click here)


12. INSTALL LICENSE PLATE LIGHT ASSEMBLY LH
  1. Engage the 2 claws to install the license plate light assembly.

  1. Connect the connector.



13. INSTALL LICENSE PLATE LIGHT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



14. INSTALL LUGGAGE COMPARTMENT DOOR OUTSIDE GARNISH SUB-ASSEMBLY
  1. Install 5 new gaskets to the luggage compartment door outside garnish sub-assembly.

  1. Install the back door opener switch assembly (Click here).

  1. Engage the clip.

  1. Install the luggage compartment door outside garnish sub-assembly with the 5 nuts.

    Torque:
    4.9 N*m{ 50 kgf*cm , 43 in.*lbf }

  1. Connect the connector.



15. INSTALL REAR TELEVISION CAMERA ASSEMBLY (w/ Rear Monitor)
  1. Engage the 2 claws to the vehicle body to temporarily install the rear television camera assembly.

  1. Install the rear television camera assembly with the 2 nuts.

    Torque:
    4.9 N*m{ 50 kgf*cm , 43 in.*lbf }

  1. Connect the connector.



16. INSTALL BACK DOOR LOCK ASSEMBLY

HINT:
Make sure to remove the string before installing a new back door lock assembly.

  1. Apply MP grease to the sliding parts of the back door lock assembly.



    B297012
  1. Install the back door lock assembly with the 2 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



    B297011
  1. Connect the connector.



17. INSTALL BACK DOOR PANEL CUSHION


    B297010
  1. Engage the 2claws to install the 2 back door panel cushions.



18. INSTALL DOOR PULL HANDLE


    B297009
  1. Engage the 4 claws to install the door pull handle.

    HINT:
    With the back door fully open, install the door pull handle so that the arrow on the backside of door pull handle points up.



19. INSTALL BACK DOOR TRIM COVER


    B297007
  1. Engage the 5 clips to install the back door trim cover.



20. INSTALL BACK DOOR TRIM BOARD ASSEMBLY


    B297006
  1. Install the back door trim board assembly with the 10 clips.