DTC P0A82-123 Hybrid Battery Pack Cooling Fan 1 Performance / Stuck OFF |
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
| P0A82 | 123 | The speed of the battery cooling blower assembly is not within the specified range (1 trip detection) |
|
| 1.CHECK FOR DTCS (HV) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / DTC.
Read output DTCs (Click here).
| Result | Proceed to |
| P0AFC-123 is not output. | A |
| P0AFC-123 is also output. | B |
Turn the power switch off.
Disconnect the intelligent tester from the DLC3.
|
| ||||
| A | |
| 2.CHECK DUCT AND BLOWER |
![]() |
Check that the front floor cover LH and battery cooling blower are not disconnected, damaged, or clogged with foreign objects, and that the acoustical materials have not peeled.
| *1 | Front Floor Cover LH |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER - BATTERY SMART UNIT) |
Check that the service plug grip is not installed.
Remove the No. 1 hybrid battery exhaust duct .
Disconnect connector M41 from the battery cooling blower assembly.
Disconnect connector M39 from the battery smart unit.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| M41-2 (FP0) - M39-5 (FP0) | Power switch off | Below 1 Ω |
| M41-2 (FP0) or M39-5 (FP0) - Body ground | Power switch off | 10 kΩ or higher |
| *a | Front view of wire harness connector (to Battery Cooling Blower Assembly) |
| *b | Rear view of wire harness connector (to Battery Smart Unit) |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| M41-2 (FP0) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Connect the battery cooling blower assembly connector.
Connect the battery smart unit connector.
Install the No. 1 hybrid battery exhaust duct.
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER - POWER MANAGEMENT CONTROL ECU) |
Check that the service plug grip is not installed.
Remove the rear seat cushion leg sub-assembly .
Disconnect connector M41 from the battery cooling blower assembly.
Disconnect connector A38 from the power management control ECU (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| M41-3 (SI0) - A38-29 (SI0) | Power switch off | Below 1 Ω |
| M41-3 (SI0) or A38-29 (SI0) - Body ground | Power switch off | 10 kΩ or higher |
| *a | Front view of wire harness connector (to Battery Cooling Blower Assembly) |
| *b | Rear view of wire harness connector (to Power Management Control ECU) |
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| M41-3 (SI0) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Connect the battery cooling blower assembly connector.
Install the rear seat cushion leg sub-assembly.
Connect the power management control ECU connector.
|
| ||||
| OK | |
| 5.CHECK POWER MANAGEMENT CONTROL ECU (GROUND SHORT CHECK) |
Remove the power management control ECU (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| A38-29 (SI0) - G57-5 (E01) | 10 kΩ or higher |
| A38-29 (SI0) - G58-5 (E02) | 10 kΩ or higher |
| *a | Component without harness connected (Power Management Control ECU) |
Install the power management control ECU.
|
| ||||
| OK | |
| 6.READ VALUE USING INTELLIGENT TESTER (COOLING FAN FREQUENCY) |
Check that the service plug grip is not installed.
Remove the rear seat cushion leg sub-assembly .
Connect the cable to the negative (-) auxiliary battery terminal.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Clear the DTCs and freeze frame data (Click here).
Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.
Enter the following menus: Powertrain / Hybrid Control / Data List / All Data / Cooling Fan Frequency 1.
Select each air volume mode (1 to 6) in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.
![]() |
While the cooling fan is operating, compare the value in the Data List (Cooling Fan Frequency1) with the frequency value that was actually measured at the battery cooling blower assembly connector.
| Tester Connection | Condition |
| M41-2 (FP0) - M41-4 (GND0) | Battery cooling blower assembly is operating |
| *a | Component with harness connected (Battery Cooling Blower Assembly) |
| *b | Rear view of wire harness connector (to Battery Cooling Blower Assembly) |
| Result | Proceed to |
| The value in the Data List (Cooling Fan Frequency 1) and the actual measurement value at the battery cooling blower assembly connector are 0 Hz. | A |
| The value in the Data List (Cooling Fan Frequency 1) and the actual measurement value at the battery cooling blower assembly connector are not 0 Hz. | B |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Install the rear seat cushion leg sub-assembly.
|
| ||||
| A | |
| 7.CHECK BATTERY SMART UNIT |
Check that the service plug grip is not installed.
Remove the rear seat cushion leg sub-assembly .
Disconnect connector M41 from the battery cooling blower assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the Turn the power switch on (IG)..
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| M41-2 (FP0) - M41-4 (GND0) | Power switch on (IG) | 4.5 to 5.5 V |
| *a | Front view of wire harness connector (to Battery Cooling Blower Assembly) |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Connect the battery cooling blower assembly connector.
Install the rear seat cushion leg sub-assembly.
|
| ||||
| OK | ||
| ||
| 8.CHECK BATTERY SMART UNIT (FREQUENCY) |
Check that the service plug grip is not installed.
Remove the rear seat cushion leg sub-assembly .
Connect the cable to the negative (-) auxiliary battery terminal.
Connect the intelligent tester. to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.
Enter the following menus: All Data / Cooling Fan Frequency 1.
Select each air volume mode (1 to 6) in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.
![]() |
While the cooling fan is operating, compare the value in the data list (Cooling Fan Frequency 1) with the Frequency value that was actually measured at the battery cooling blower assembly connector.
| Tester Connection | Condition | Specified Condition |
| M41-2 (FP0) - M41-4 (GND0) | Battery cooling blower is operating | Difference between the value in the Data List (Cooling Fan Frequency 1) and the actual measurement value is 10 % or less. |
| *a | Component with harness connected (Battery Cooling Blower Assembly) |
| *b | Rear view of wire harness connector (to Battery Cooling Blower Assembly) |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Install the rear seat cushion leg sub-assembly.
|
| ||||
| OK | ||
| ||