Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM

DTC    P0A84-123    Hybrid Battery Pack Cooling Fan 1 Control Circuit Low

for Preparation Click here


DESCRIPTION


  1. The speed of the battery cooling blower assembly is controlled by the power management control ECU. Power is supplied to the battery cooling blower assembly when the MREL terminal of the power management control ECU turns on the IGCT relay. The power management control ECU sends command signals (SI) to the battery cooling blower assembly to adjust the fan speed to an appropriate speed for the HV battery temperature. The battery cooling blower assembly frequency (FP) is sent to the power management control ECU via the battery smart unit as a monitor signal using serial communication.


    A260101E01


DTC No.
INF Code
DTC Detection Condition
Trouble Area
P0A84
123
When the speed calculated based on the battery cooling blower assembly frequency (FP) is out of the target control speed range (1 trip detection)
  1. Wire harness or connector
  2. BATT FAN fuse
  3. Battery cooling blower assembly
  4. Battery smart unit
  5. Power management control ECU

WIRING DIAGRAM


A244326E02


INSPECTION PROCEDURE

CAUTION:
  1. Before inspecting the high-voltage system, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
  2. After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (Click here).

    HINT:
    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).

1.CHECK FOR DTCS (HV)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Read output DTCs (Click here).

    Result:
    Result
    Proceed to
    P0AFC-123 is not output.
    A
    P0AFC-123 is also output.
    B

  1. Turn the power switch off.

  1. Disconnect the intelligent tester from the DLC3.



B
GO TO DTC CHART (P0AFC-123) (Click here)
A


2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.

    NOTICE:
    If the Active Test cannot be performed, skip it and proceed to the next step to check fan operates and air is sucked. In accordance with fail-safe system operation, the power management control ECU sends a command to operate the battery cooling fan.

  1. Select air volume mode 6 in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.

  1. Check that the fan operates and air is sucked into the inlet duct.

    HINT:
    The cooling fan may not stop even when turning the cooling fan off in the "Driving the Battery Cooling Fan" Active Test. This is due to HV system control and not a malfunction.

    OK:
    The fan operates.

  1. Turn the power switch off.



NG
Go to step 7
OK


3.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER - BATTERY SMART UNIT)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the No. 1 hybrid battery exhaust duct .

  1. Disconnect connector M41 from the battery cooling blower assembly.

  1. Disconnect connector M39 from the battery smart unit.



    A259921E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    M41-2 (FP0) - M39-5 (FP0)
    Power switch off
    Below 1 Ω
    M41-2 (FP0) or M39-5 (FP0) - Body ground
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Battery Cooling Blower Assembly)
    *b
    Rear view of wire harness connector
    (to Battery Smart Unit)

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    M41-2 (FP0) - Body ground
    Power switch on (IG)
    Below 1 V

    NOTICE:
    Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

    HINT:
    As there might be an intermittent malfunction, inspect the following items even if the measured voltage is as specified. Check that each connector between the battery voltage sensor and battery cooling blower assembly is not loose or disconnected.

  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Connect the battery cooling blower assembly connector.

  1. Connect the battery smart unit connector.

  1. Install the No. 1 hybrid battery exhaust duct.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY COOLING BLOWER - BATTERY SMART UNIT)
OK


4.READ VALUE USING INTELLIGENT TESTER (COOLING FAN FREQUENCY)

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the rear seat cushion leg sub-assembly .

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Clear the DTCs and freeze frame data (Click here).

  1. Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.

  1. Enter the following menus: Powertrain / Hybrid Control / Data List / All Data / Cooling Fan Frequency 1.

  1. Select each air volume mode (1 to 6) in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.

    NOTICE:
    If the Active Test cannot be performed, skip it and proceed to the next step to check the frequency value. In accordance with fail-safe system operation, the power management control ECU sends a command to operate the battery cooling fan assembly.



    A266555E03
  1. While the cooling fan is operating, compare the value in the Data List (Cooling Fan Frequency1) with the frequency value that was actually measured at the battery cooling blower assembly connector.

    Standard:
    Tester Connection
    Condition
    M41-2 (FP0) - M41-4 (GND0)
    Battery cooling blower assembly is operating

    Text in Illustration 
    *a
    Component with harness connected
    (Battery Cooling Blower Assembly)
    *b
    Rear view of wire harness connector
    (to Battery Cooling Blower Assembly)

    Result:
    Result
    Proceed to
    The value in the Data List (Cooling Fan Frequency 1) and the actual measurement value at the battery cooling blower assembly connector are 0 Hz.
    A
    The value in the Data List (Cooling Fan Frequency 1) and the actual measurement value at the battery cooling blower assembly connector are not 0 Hz.
    B

    NOTICE:
    Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

    HINT:
    Compare the values in each air volume mode (1 to 6). If the Active Test cannot be performed, compare the values only in the current air volume mode.

  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Install the rear seat cushion leg sub-assembly.



B
Go to step 6
A


5.CHECK BATTERY SMART UNIT

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the rear seat cushion leg sub-assembly .

  1. Disconnect connector M41 from the battery cooling blower assembly.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the Turn the power switch on (IG)..

    NOTICE:
    1. After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
    2. If the power switch is turned on (IG) with the service plug grip removed, DTC P0A0D-350 for the interlock switch system will be stored. If this DTC is output, clear the DTC using the intelligent tester (Click here).



    A342209E05
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    M41-2 (FP0) - M41-4 (GND0)
    Power switch on (IG)
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Battery Cooling Blower Assembly)

    NOTICE:
    Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Connect the battery cooling blower assembly connector.

  1. Install the rear seat cushion leg sub-assembly.



NG
REPLACE BATTERY SMART UNIT (Click here)
OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY (Click here)  

6.CHECK BATTERY SMART UNIT (FREQUENCY)
  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the rear seat cushion leg sub-assembly .

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Connect the intelligent tester. to the DLC3.

  1. Turn the power switch on (IG).

    NOTICE:
    1. After removing the service plug grip, do not turn the power switch on (READY) unless instructed by the repair manual because this may cause a malfunction.
    2. If the power switch is turned on (IG) with the service plug grip removed, DTC P0A0D-350 for the interlock switch system will be stored. If this DTC is output, clear the DTC using the intelligent tester. (Click here).

  1. Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.

    NOTICE:
    If the Active Test cannot be performed, skip it and proceed to the next step to check Frequency. In accordance with fail-safe system operation, the power management control ECU sends a command to operate the battery cooling fan.

  1. Enter the following menus: All Data / Cooling Fan Frequency 1.

  1. Select each air volume mode (1 to 6) in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.



    A266555E03
  1. While the cooling fan is operating, compare the value in the data list (Cooling Fan Frequency 1) with the Frequency value that was actually measured at the battery cooling blower assembly connector.

    Standard:
    Tester Connection
    Condition
    Specified Condition
    M41-2 (FP0) - M41-4 (GND0)
    Battery cooling blower is operating
    Difference between the value in the Data List (Cooling Fan Frequency 1) and the actual measurement value is 10 % or less.

    Text in Illustration 
    *a
    Component with harness connected
    (Battery Cooling Blower Assembly)
    *b
    Rear view of wire harness connector
    (to Battery Cooling Blower Assembly)

NOTICE:
Turning the power switch on (IG) with the service grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

HINT:
Compare the values in each air volume mode (1 to 6). If the active test cannot be performed, compare the values only in the current air volume mode.

  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Install the rear seat cushion leg sub-assembly.



NG
REPLACE BATTERY SMART UNIT (Click here)
OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY (Click here)  

7.CHECK FUSE (BATT FAN)
  1. Remove the BATT FAN fuse from the No. 2 engine room relay block and No. 2 junction block assembly.



    A244331E01
  1. Measure the resistance of the BATT FAN fuse.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    BATT FAN fuse
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
    *2
    BATT FAN Fuse



NG
Go to step 14
OK


8.CHECK HARNESS AND CONNECTOR (IGCT RELAY - BATTERY COOLING BLOWER ASSEMBLY) (VOLTAGE)
  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the rear seat cushion leg sub-assembly .

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

    NOTICE:
    1. After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
    2. If the power switch is turned on (IG) with the service plug grip removed, DTC P0A0D-350 for the interlock switch system will be stored. If this DTC is output, clear the DTC using the intelligent tester (Click here).

  1. Enter the following menus: Powertrain / Hybrid Control / DTC.

  1. Clear the DTCs and freeze frame data (Click here).



    A266555E04
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    M41-1 (IG0) - Body ground
    Battery cooling blower is operating
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (Battery Cooling Blower Assembly)
    *b
    Rear view of wire harness connector
    (to Battery Cooling Blower Assembly)

    NOTICE:
    Turning the power switch on (IG) with the service grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

    HINT:
    Measure the voltage on the wire side of the connector that is part of the battery cooling blower.

  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Install the rear seat cushion leg sub-assembly.



NG
Go to step 11
OK


9.CHECK HARNESS AND CONNECTOR (BATTERY COOLING BLOWER - POWER MANAGEMENT CONTROL ECU)
  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the rear seat cushion leg sub-assembly .

  1. Disconnect connector M41 from the battery cooling blower assembly.

  1. Disconnect connector A38 from the power management control ECU (Click here).



    A217831E12
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Switch Condition
    Specified Condition
    M41-3 (SI0) - A38-29 (SI0)
    Power switch off
    Below 1 Ω
    M41-3 (SI0) or A38-29 (SI0) - Body ground
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Battery Cooling Blower Assembly)
    *b
    Rear view of wire harness connector
    (to Power Management Control ECU)

    NOTICE:
    When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Turn the power switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    M41-3 (SI0) - Body ground
    Power switch on (IG)
    Below 1 V

NOTICE:
Turning the power switch on (IG) with the battery cooling blower assembly connector and power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Connect the battery cooling blower assembly connector.

  1. Install the rear seat cushion leg sub-assembly.

  1. Connect the power management control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10.CHECK BATTERY COOLING BLOWER ASSEMBLY

CAUTION:
Be sure to wear insulated gloves.

  1. Check that the service plug grip is not installed.

    NOTICE:
    After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

  1. Remove the rear seat cushion leg sub-assembly (Click here).

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

  1. Clear the DTCs and freeze frame data (Click here).

  1. Enter the following menus: Powertrain / Hybrid Control / Active Test / Driving the Battery Cooling Fan.

  1. Select each air volume mode (1 to 6) in the "Driving the Battery Cooling Fan" Active Test to operate the battery cooling blower assembly.

    NOTICE:
    If the Active Test cannot be performed, skip it and proceed to the next step to check the waveform. In accordance with fail-safe system operation, the power management control ECU sends a command to operate the battery cooling blower assembly.

  1. Connect an oscilloscope between the battery cooling blower assembly terminals specified in the following table.



    A266555E12
  1. Check the waveform.

    Specified Condition:
    Tester Connection
    Switch Condition
    Specified Condition
    M41-3 (SI0) - M41-4 (GND0)
    Power switch on (IG), during Active Test
    Pulse generation
    Text in Illustration 
    *a
    Component with harness connected
    (Battery Cooling Blower Assembly)
    *b
    Rear view of wire harness connector
    (to Battery Cooling Blower Assembly)

    NOTICE:
    Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

    HINT:
    Perform this inspection with the battery cooling blower assembly connector connected.

  1. Turn the power switch off.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal.

  1. Install the rear seat cushion leg sub-assembly.



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY (Click here)  

11.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)
  1. Disconnect connector G57 from the power management control ECU (Click here).



    A212482E12
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G57-5 (E01) - Body ground
    Power switch off
    Below 1 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)

    NOTICE:
    When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.

  1. Connect the power management control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)
  1. Disconnect connector G58 from the power management control ECU (Click here).



    A212483E10
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G58-5 (E02) - Body ground
    Power switch off
    Below 1 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)

    NOTICE:
    When taking a measurement with a tester, do not apply excessive force to the tester probe to avoid damaging the holder.

  1. Connect the power management control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13.CHECK HARNESS AND CONNECTOR (IGCT RELAY - BATTERY COOLING BLOWER ASSEMBLY)
  1. Remove the IGCT relay.

  1. Remove the rear seat cushion leg sub-assembly .

  1. Disconnect connector M41 from the battery cooling blower assembly.



    A244333E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (IGCT relay block) - M41-1 (IG0)
    Power switch off
    Below 1 Ω

    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
    *2
    IGCT Relay
    *a
    Front view of wire harness connector
    (to Battery Cooling Blower Assembly)

  1. Install the IGCT relay.

  1. Connect the battery cooling blower assembly connector.

  1. Install the rear seat cushion leg sub-assembly.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)  

14.CHECK HARNESS AND CONNECTOR (BATT FAN FUSE - BATTERY COOLING BLOWER ASSEMBLY)
  1. Remove the BATT FAN fuse.

  1. Remove the rear seat cushion leg sub-assembly .

  1. Disconnect connector M41 from the battery cooling blower assembly.



    A244332E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    M41-1 (IG0) - Terminals other than 2 (BATT FAN fuse block) and body ground
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *1
    No. 2 Engine Room Relay Block and No. 2 Junction Block Assembly
    *2
    BATT FAN fuse
    *a
    Front view of wire harness connector
    (to Battery Cooling Blower Assembly)

  1. Install the BATT FAN fuse.

  1. Connect the battery cooling blower assembly connector.

  1. Install the rear seat cushion leg sub-assembly.



NG
Go to step 16
OK


15.CHECK BATTERY COOLING BLOWER ASSEMBLY
  1. Remove the rear seat cushion leg sub-assembly .

  1. Disconnect connector M41 from the battery cooling blower assembly.



    A221313E30
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    M41-1 (IG0) - M41-4 (GND0) and body ground
    Power switch off
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Battery Cooling Blower Assembly)

  1. Connect the battery cooling blower assembly connector.

  1. Install the rear seat cushion leg sub-assembly.



NG
Go to step 17
OK

REPLACE FUSE (BATT FAN) 

16.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

REPLACE FUSE (BATT FAN) 

17.REPLACE BATTERY COOLING BLOWER ASSEMBLY
(Click here)

NEXT

REPLACE FUSE (BATT FAN)