CAMSHAFT > REMOVAL |
| 1. REMOVE EGR COOLER ASSEMBLY |
| 2. SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (for RHD) |
![]() |
Disconnect the connector.
Remove the bolt and nut, and separate the brake master cylinder reservoir assembly.
| 3. REMOVE IGNITION COIL ASSEMBLY |
![]() |
Disconnect the 4 No. 1 ignition coil connectors.
Remove the 4 bolts and 4 No. 1 ignition coils.
| 4. SEPARATE ENGINE WIRE (for LHD) |
![]() |
Disconnect the 4 injector connectors.
![]() |
Disconnect the wire harness clamp.
Remove the 3 bolts and separate the engine wire.
| 5. SEPARATE ENGINE WIRE (for RHD) |
![]() |
Disconnect the 4 injector connectors.
![]() |
Remove the 3 bolts and separate the engine wire.
| 6. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Disconnect the No. 1 ventilation hose and No. 2 ventilation hose.
![]() |
Remove the 9 bolts, 2 seal washers, 2 nuts and cylinder head cover sub-assembly.
Remove the gasket from the cylinder head cover sub-assembly.
| 7. SET NO. 1 CYLINDER TO TDC / COMPRESSION |
![]() |
Turn the crankshaft damper until its notch and timing mark "0" of the timing chain cover are aligned.
| *a | Timing Mark |
| *b | Timing Notch |
| *c | Timing Mark (Rectangle) |
| *d | Mark (Circle) |
| *e | Paint Mark |
Check that the timing marks on both the camshaft timing gear or sprocket and the camshaft timing gear assembly are facing upward as shown in the illustration.
Place paint marks on the chain sub-assembly in alignment with the timing marks on the camshaft timing gear assembly and camshaft timing gear or sprocket.
| 8. REMOVE SCREW PLUG |
![]() |
Using a 8 mm hexagon socket wrench, remove the screw plug.
| 9. REMOVE NO. 2 CAMSHAFT |
![]() |
Loosen the bolts on the camshaft timing gear or sprocket while holding the hexagonal portion of the No. 2 camshaft.
| *a | Hold |
![]() |
Insert a screwdriver from the plug hole and turn the stopper plate of the No. 1 chain tensioner assembly clockwise to release the lock, and keep it as it is.
| *1 | Plunger |
| *2 | Stopper Plate |
| *a | Unlock |
![]() |
Slightly turn the hexagonal portion of the No. 2 camshaft clockwise so that the plunger of the No. 1 chain tensioner assembly is pushed by the chain sub-assembly.
| *1 | Plunger |
![]() |
Insert a screwdriver from the plug hole and turn the stopper plate of the No. 1 chain tensioner assembly counterclockwise to the lock, and keep it as it is. Insert the hexagon wrench into the stopper plate hole.
| *1 | Hexagon Wrench |
| *2 | Plunger |
| *3 | Stopper Plate |
| *a | Lock |
![]() |
Using several steps, uniformly loosen and remove the 11 bolts in the sequence shown in the illustration. Then remove the No. 1 camshaft bearing cap and 4 No. 2 camshaft bearing caps.
![]() |
Remove the bolt with the No. 2 camshaft lifted up.
Remove the No. 2 camshaft and camshaft timing gear or sprocket.
| 10. REMOVE CAMSHAFT |
![]() |
Loosen the bolts on the camshaft timing gear assembly while holding the hexagonal portion of the camshaft.
| *a | Hold |
![]() |
Using several steps, uniformly loosen and remove the 8 bolts in the sequence shown in the illustration. Then remove the 4 No. 2 camshaft bearing caps.
![]() |
Hold the chain sub-assembly with one hand, and remove the camshaft.
![]() |
Tie the chain sub-assembly with a string or similar as shown in the illustration.
| 11. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY |
Check the camshaft timing gear assembly lock.
![]() |
Clamp the camshaft in a vise, and make sure that the camshaft timing gear assembly does not rotate.
Release the lock pin.
![]() |
Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.
| *a | Retard Side Path |
| *b | Advance Side Path |
| *c | Open |
| *d | Close |
![]() | Rubber Piece |
![]() | Vinyl Tape |
Prick a hole in the tape placed on the advance side path. Prick a hole in the tape placed on the retard side path, on the opposite side to that of the advance side path, as shown in the illustration.
![]() |
Apply approximately 150 kPa (1.5 kgf/cm2, 22 psi) of air pressure to the 2 paths (the advance side path and the retard side path).
| *a | Advance Side Path |
| *b | Retard Side Path |
![]() |
Make sure that the camshaft timing sprocket turns in the retard direction when reducing the air pressure applied to the advance side path.
| *a | Advance Side Path |
| *b | Retard Side Path |
| *c | Decompress |
| *d | Hold Pressure |
When the camshaft timing sprocket moves to the most retarded position, release the air pressure from the advance side path, and then release the air pressure from the retard side path.
| 12. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY |
![]() |
Remove the bolt and camshaft timing gear assembly.
| *a | Do Not Remove |