Home › Engine / Hybrid System › 1NZ-FXE ENGINE MECHANICAL › CAMSHAFT

CAMSHAFT > REMOVAL

for Preparation Click here



1. REMOVE EGR COOLER ASSEMBLY
(Click here)


2. SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (for RHD)


    A266931
  1. Disconnect the connector.

  1. Remove the bolt and nut, and separate the brake master cylinder reservoir assembly.



3. REMOVE IGNITION COIL ASSEMBLY


    A267419
  1. Disconnect the 4 No. 1 ignition coil connectors.

  1. Remove the 4 bolts and 4 No. 1 ignition coils.

    NOTICE:
    When removing each ignition coil, do not damage the plug cap on the engine head cover opening or the upper edge of the spark plug tube.



4. SEPARATE ENGINE WIRE (for LHD)


    A266930
  1. Disconnect the 4 injector connectors.



    A268171
  1. Disconnect the wire harness clamp.

  1. Remove the 3 bolts and separate the engine wire.



5. SEPARATE ENGINE WIRE (for RHD)


    A266930
  1. Disconnect the 4 injector connectors.



    A266929
  1. Remove the 3 bolts and separate the engine wire.



6. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    A266933
  1. Disconnect the No. 1 ventilation hose and No. 2 ventilation hose.



    A265764
  1. Remove the 9 bolts, 2 seal washers, 2 nuts and cylinder head cover sub-assembly.

  1. Remove the gasket from the cylinder head cover sub-assembly.



7. SET NO. 1 CYLINDER TO TDC / COMPRESSION


    A266919E01
  1. Turn the crankshaft damper until its notch and timing mark "0" of the timing chain cover are aligned.
    Text in Illustration 
    *a
    Timing Mark
    *b
    Timing Notch
    *c
    Timing Mark (Rectangle)
    *d
    Mark (Circle)
    *e
    Paint Mark

  1. Check that the timing marks on both the camshaft timing gear or sprocket and the camshaft timing gear assembly are facing upward as shown in the illustration.

    HINT:
    1. If not, turn the crankshaft 1 complete revolution (360°) and align the marks as above.
    2. There are 3 marks on the camshaft timing gear or sprocket. Make sure that the timing mark (rectangle) is at the top.

  1. Place paint marks on the chain sub-assembly in alignment with the timing marks on the camshaft timing gear assembly and camshaft timing gear or sprocket.



8. REMOVE SCREW PLUG


    A266922
  1. Using a 8 mm hexagon socket wrench, remove the screw plug.



9. REMOVE NO. 2 CAMSHAFT


    A266923E01
  1. Loosen the bolts on the camshaft timing gear or sprocket while holding the hexagonal portion of the No. 2 camshaft.
    Text in Illustration 
    *a
    Hold



    A266920E01
  1. Insert a screwdriver from the plug hole and turn the stopper plate of the No. 1 chain tensioner assembly clockwise to release the lock, and keep it as it is.
    Text in Illustration 
    *1
    Plunger
    *2
    Stopper Plate
    *a
    Unlock

    HINT:
    1. The plunger of the No. 1 chain tensioner assembly is locked.
    2. If the stopper plate is locked firmly, slightly turn the hexagonal portion of the camshaft to the right and left.



    A266924E01
  1. Slightly turn the hexagonal portion of the No. 2 camshaft clockwise so that the plunger of the No. 1 chain tensioner assembly is pushed by the chain sub-assembly.
    Text in Illustration 
    *1
    Plunger



    A268178E01
  1. Insert a screwdriver from the plug hole and turn the stopper plate of the No. 1 chain tensioner assembly counterclockwise to the lock, and keep it as it is. Insert the hexagon wrench into the stopper plate hole.
    Text in Illustration 
    *1
    Hexagon Wrench
    *2
    Plunger
    *3
    Stopper Plate
    *a
    Lock

    HINT:
    Hold the hexagon wrench with tape so that the hexagon wrench does not come off.



    A267006E01
  1. Using several steps, uniformly loosen and remove the 11 bolts in the sequence shown in the illustration. Then remove the No. 1 camshaft bearing cap and 4 No. 2 camshaft bearing caps.

    NOTICE:
    Uniformly loosen the bolts while keeping the No. 2 camshaft level.



    A037148
  1. Remove the bolt with the No. 2 camshaft lifted up.

  1. Remove the No. 2 camshaft and camshaft timing gear or sprocket.



10. REMOVE CAMSHAFT


    A266926E01
  1. Loosen the bolts on the camshaft timing gear assembly while holding the hexagonal portion of the camshaft.
    Text in Illustration 
    *a
    Hold



    A267005E01
  1. Using several steps, uniformly loosen and remove the 8 bolts in the sequence shown in the illustration. Then remove the 4 No. 2 camshaft bearing caps.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.



    A035767
  1. Hold the chain sub-assembly with one hand, and remove the camshaft.



    A266927
  1. Tie the chain sub-assembly with a string or similar as shown in the illustration.

    NOTICE:
    Be careful not to drop anything inside the timing chain cover.



11. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY


  1. Check the camshaft timing gear assembly lock.



      A267919
    1. Clamp the camshaft in a vise, and make sure that the camshaft timing gear assembly does not rotate.



  1. Release the lock pin.



      A266804E01
    1. Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.
      Text in Illustration 
      *a
      Retard Side Path
      *b
      Advance Side Path
      *c
      Open
      *d
      Close
      V100144
      Rubber Piece
      V100145
      Vinyl Tape

      HINT:
      4 oil paths are provided in the groove. Plug 2 paths with rubber pieces.

    2. Prick a hole in the tape placed on the advance side path. Prick a hole in the tape placed on the retard side path, on the opposite side to that of the advance side path, as shown in the illustration.



    3. A146376E01
    4. Apply approximately 150 kPa (1.5 kgf/cm2, 22 psi) of air pressure to the 2 paths (the advance side path and the retard side path).
      Text in Illustration 
      *a
      Advance Side Path
      *b
      Retard Side Path

      HINT:
      Cover the paths with a piece of cloth when applying pressure to keep oil from splashing.



    5. A146374E01
    6. Make sure that the camshaft timing sprocket turns in the retard direction when reducing the air pressure applied to the advance side path.
      Text in Illustration 
      *a
      Advance Side Path
      *b
      Retard Side Path
      *c
      Decompress
      *d
      Hold Pressure

      HINT:
      The lock pin is released and the camshaft timing sprocket turns in the retard direction.

    7. When the camshaft timing sprocket moves to the most retarded position, release the air pressure from the advance side path, and then release the air pressure from the retard side path.

      NOTICE:
      Be sure to release the air pressure from the advance side path first. If the air pressure of the retard side path is released first, the camshaft timing sprocket may abruptly shift in the advance direction and break the lock pin or other parts.



12. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY


    A032639E06
  1. Remove the bolt and camshaft timing gear assembly.
    Text in Illustration 
    *a
    Do Not Remove

    NOTICE:
    1. Be sure not to remove the other 4 bolts.
    2. When reusing the camshaft timing gear assembly, release the lock pin first, then install the camshaft timing gear assembly.