Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM

DTC    C2171/71    Transmitter ID not Registered

for Preparation Click here


DESCRIPTION

The IDs of each tire pressure warning valve and transmitter are registered to the tire pressure warning ECU and receiver.
When the ECU detects that a transmitter ID code is not registered in the ECU, a DTC is stored.

DTC No.
DTC Detection Condition
Trouble Area
C2171/71
Transmitter ID code is not registered. (When an ID code is unregistered for 3 minutes or more)
Tire pressure warning ECU and receiver

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.
  2. It is necessary to perform initialization (Click here) after registration (Click here) of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.

1.CONFIRM REGISTRATION CONDITION (REGISTERED ID CODES)
  1. Turn the power switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

  1. Check the values by referring to the table below.

    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Registered ID 1 code
    Registered ID1 code/
    min.: 0
    max.: FFFFFFF*1
    ID No. registered for transmitter ID1 displayed
    -
    Registered ID 2 code
    Registered ID2 code/
    min.: 0
    max.: FFFFFFF*1
    ID No. registered for transmitter ID2 displayed
    -
    Registered ID 3 code
    Registered ID3 code/
    min.: 0
    max.: FFFFFFF*1
    ID No. registered for transmitter ID3 displayed
    -
    Registered ID 4 code
    Registered ID4 code/
    min.: 0
    max.: FFFFFFF*1
    ID No. registered for transmitter ID4 displayed
    -

    HINT:
    *1: Displayed only when the ID No. is not registered.

    OK:
    The registered transmitter ID codes are displayed on the GTS.



NG
Go to step 2
OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER (Click here)  

2.PERFORM REGISTRATION (TRANSMITTER ID)
  1. Perform registration (Click here).


NEXT


3.PERFORM INITIALIZATION
  1. Perform initialization (Click here).


NEXT


4.CONFIRM TIRE INFLATION PRESSURE (DATA LIST)
  1. Turn the power switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

  1. Check the values by referring to the table below.

    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ID 1 Tire Inflation Pressure
    ID1 tire inflation pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*1
    ID 2 Tire Inflation Pressure
    ID2 tire inflation pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*1
    ID 3 Tire Inflation Pressure
    ID3 tire inflation pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*1
    ID 4 Tire Inflation Pressure
    ID4 tire inflation pressure/
    min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi)
    Actual tire inflation pressure
    If N/A is displayed, data has not been received.*1

    HINT:
    1. *1: It may take a few minutes until the values are displayed.
    2. When an "ID Tire Inflation Pressure" value has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the value.


    Result:

    Result
    Proceed to
    All tire pressure readings are equal to specified values.
    A
    Tire pressure values are not displayed.
    B



B
REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER (Click here)
A

END