Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Microphone Circuit between Microphone and Radio Receiver

for Preparation Click here


DESCRIPTION

Using this circuit, the radio receiver assembly sends power to the amplifier microphone assembly, and the amplifier microphone assembly sends microphone signals to the radio receiver assembly.

WIRING DIAGRAM


E204785E09


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - AMPLIFIER MICROPHONE ASSEMBLY)
  1. Disconnect the radio receiver assembly and amplifier microphone assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G41-6 (SNS2) - Q5-4 (SNS2)
    Always
    Below 1 Ω
    G41-4 (MACC) - Q5-1 (MACC)
    Always
    Below 1 Ω
    G41-5 (MIN+) - Q5-2 (MCO+)
    Always
    Below 1 Ω
    G41-19 (MIN-) - Q5-3 (MCO-)
    Always
    Below 1 Ω
    G41-6 (SNS2) - Body ground
    Always
    10 kΩ or higher
    G41-4 (MACC) - Body ground
    Always
    10 kΩ or higher
    G41-5 (MIN+) - Body ground
    Always
    10 kΩ or higher
    G41-19 (MIN-) - Body ground
    Always
    10 kΩ or higher
    G41-18 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.INSPECT RADIO RECEIVER ASSEMBLY
  1. Reconnect the radio receiver assembly connector.

  1. Reconnect the amplifier microphone assembly connector.



    E237416E14
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G41-4 (MACC) - Body ground
    Power switch on (ACC)
    4 to 6 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G41-18 (SGND) - Body ground
    Always
    Below 1 Ω
    G41-19 (MIN-) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Radio Receiver Assembly)



NG
REPLACE RADIO RECEIVER ASSEMBLY (Click here)
OK


3.INSPECT AMPLIFIER MICROPHONE ASSEMBLY
  1. Disconnect the amplifier microphone assembly connector.



    E244512E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Q5-3 (MCO-) - Q5-4 (SNS2)
    Always
    Below 1 Ω

Text in Illustration 
*a
Component without harness connected
(Amplifier Microphone Assembly)


NG
REPLACE AMPLIFIER MICROPHONE ASSEMBLY (Click here)
OK


4.INSPECT AMPLIFIER MICROPHONE ASSEMBLY
  1. Reconnect the radio receiver assembly connector.



    E244513E01
  1. Reconnect the amplifier microphone assembly connector.

  1. Turn the power switch to ACC.

  1. Connect an oscilloscope to terminals 2 (MCO+) and 3 (MCO-) of the amplifier microphone assembly connector.

  1. Check the waveform of the amplifier microphone assembly using the oscilloscope.

    Result:
    Result
    Proceed to
    A waveform synchronized with the voice input to the amplifier microphone assembly is output
    A
    A waveform synchronized with the voice input to the amplifier microphone assembly is not output
    B

Text in Illustration 
*a
Component with harness connected
(Amplifier Microphone Assembly)


B
REPLACE AMPLIFIER MICROPHONE ASSEMBLY (Click here)
A

END