Home › Vehicle Exterior › VEHICLE PROXIMITY NOTIFICATION SYSTEM › VEHICLE PROXIMITY NOTIFICATION SYSTEM

VEHICLE PROXIMITY NOTIFICATION SYSTEM > The Sound does not Stop when The Engine is Operated or when The Shift Lever is in P

for Preparation Click here


DESCRIPTION

The vehicle approaching speaker controller receives engine oil pressure switch signals from the engine oil pressure switch assembly and P position switch signals from the lower shift lever assembly, and produces the warning sound from the vehicle approaching speaker assembly.

WIRING DIAGRAM


E342158E01


INSPECTION PROCEDURE

1.READ VALUE USING GTS (Oil Pressure SW)
  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.

  1. Read the Data List according to the display on the GTS.

    Vehicle Proximity Notification System 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Oil Pressure SW
    Oil pressure switch / OFF or ON
    OFF: Engine started
    ON: Engine not started
    -

    Result:
    Result
    Proceed to
    The GTS display changes according to engine operation
    A
    The GTS display does not change according to engine operation
    B



B
Go to step 6
A


2.READ VALUE USING GTS (Shift Position)
  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.

  1. Read the Data List according to the display on the GTS.

    Vehicle Proximity Notification System 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Shift Position
    P position switch / Not Parking or Parking
    Not Parking or Parking
    -

    Result:
    Result
    Proceed to
    The GTS display changes according to the selected shift state
    A
    The GTS display does not change according to the selected shift state
    B



B
Go to step 3
A

REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER (Click here)  

3.CHECK VEHICLE APPROACHING SPEAKER CONTROLLER (SHIFT)
  1. Disconnect the G25 lower shift lever assembly connector.



    E289606E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G25-2 (P2) - Body ground
    Power switch on (IG)
    8 V or higher
    Power switch off
    Below 1 V

Text in Illustration 
*a
Front view of wire harness connector
(to Lower Shift Lever Assembly)


NG
Go to step 5
OK


4.CHECK LOWER SHIFT LEVER ASSEMBLY
  1. Reconnect the G25 lower shift lever assembly connector.



    E289963E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G25-2 (P2) - Body ground
    Power switch on (IG), park (P) selected
    8 V or higher
    Power switch on (IG), park (P) not selected
    Below 2.5 V

Text in Illustration 
*a
Component with harness connected
(Lower Shift Lever Assembly)


NG
REPLACE LOWER SHIFT LEVER ASSEMBLY (Click here)
OK

REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER (Click here)  

5.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - LOWER SHIFT LEVER ASSEMBLY)
  1. Disconnect the G85 vehicle approaching speaker controller connector.

  1. Disconnect the G25 lower shift lever assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G85-11 (SFTP) - G25-2 (P2)
    Always
    Below 1 Ω
    G85-11 (SFTP) or G25-2 (P2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER (Click here)  

6.CHECK ENGINE OIL PRESSURE SWITCH ASSEMBLY (INPUT SIGNAL)
  1. Disconnect the G85 vehicle approaching speaker controller connector.



    E285131E14
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G85-12 (OPSW) - Body ground
    Idling*
    8 V or higher
    Power switch on (IG)
    Below 2 V

    HINT:
    *:Put the engine in inspection mode (Click here).

Text in Illustration 
*a
Front view of wire harness connector
(to Vehicle Approaching Speaker Controller)


NG
Go to step 7
OK

REPLACE VEHICLE APPROACHING SPEAKER CONTROLLER (Click here)  

7.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - ENGINE OIL PRESSURE SWITCH ASSEMBLY)
  1. Disconnect the G85 vehicle approaching speaker controller connector.

  1. Disconnect the E2 engine oil pressure switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G85-12 (OPSW) - E2-1
    Always
    Below 1 Ω
    G85-12 (OPSW) or E2-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ENGINE OIL PRESSURE SWITCH ASSEMBLY (Click here)