Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR

FRONT DOOR > REASSEMBLY

for Preparation Click here


HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedure described below is for the LH side.



1. PRECAUTION

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here)



2. REPAIR INSTRUCTION
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.
      Heating Temperature 
      Item
      Temperature
      Vehicle Body
      40 to 60°C (104 to 140°F)

      NOTICE:
      Do not heat the vehicle body excessively.

    2. Wipe off any tape adhesive residue with cleaner.

  1. Installation temperature

    1. When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape up to between 20 and 30°C (68 and 86°F) using a heat light. When the ambient temperature is above 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape down to between 20 and 30°C (68 and 86°F) prior to installation.

      HINT:
      1. The most appropriate temperature for installing the tape is 25°C (77°F).
      2. When the temperature is low, the tape turns stiff and comes off easily. When the temperature is high, the tape elasticity increases.

  1. Before installation

    1. Remove any coating roughness or dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame). If any roughness or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.

      HINT:
      Spray water on the shop floor to settle any dust.

  1. Key points for handling the tape

    1. The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and flat.

      NOTICE:
      Do not bend the tape or leave it in high temperature places.



  1. Key points for installation of the tape (how to use a squeegee and installation procedure for flat surfaces)

    NOTICE:
    1. Position the tape accurately to achieve a neat finish and to avoid peeling.
    2. The tape cannot be reused because it deforms and will not fit any more after being removed.




    1. To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee at 40 to 50° (pressing forward) or 30 to 45° (pulling) to the vehicle body surface and press the tape onto the vehicle body surface with a force of 20 to 30 N (2 to 3 kgf, 4.5 to 6.7 lbf) at a constant slow speed of 3 to 7 cm (1.18 to 2.76 in.) per second.


      B200106E02


      Text in Illustration 
      *A
      Pressing Forward
      *B
      Pulling
      *1
      Non-padded Side
      *2
      Padded Side
      *3
      Squeegee
      *4
      Black Out Tape
      *5
      Release Paper
      -
      -
      *a
      Side View
      -
      -
      Reference Measurement 
      Area
      Measurement
      A
      10 to 20 mm (0.393 to 0.787 in.)
      B
      30 to 70 mm/sec. (1.18 to 2.76 in./sec.)
      C
      40 to 50° (for pressing forward)
      D
      30 to 45° (for pulling)

      NOTICE:
      Be sure to observe the specified pressing speed, force and angle of the squeegee to avoid wrinkles or air bubbles.

      HINT:
      1. Either angle of the squeegee (pressing forward or pulling) is acceptable.
      2. Be sure to apply the tape while removing the release paper 10 to 20 mm (0.394 to 0.787 in.) from the edge of the squeegee.



  1. Key points for installation of the tape (how to use a squeegee and installation procedure for hemmed surfaces)



      B147253E09
    1. If it is difficult to apply the tape, install it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.
      Text in Illustration 
      *1
      Squeegee
      *2
      Hem
      *a
      First
      *b
      Second
      *c
      Third

      HINT:
      When applying tape to the backside of a hem, remove the release paper and use your fingers or the padded surface of a squeegee.

  1. Key points for installation of the tape (how to use a squeegee and installation procedure for corners)

    1. Remove the release paper and apply the tape carefully with your fingers.

    2. Before applying the tape to each corner, heat the tape using a heat light and gradually apply it, avoiding wrinkles on the tape to achieve a neat finish.

  1. Check after installation

    1. After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, reapply using new tape.

      NOTICE:
      Do not reuse the tape.



3. INSTALL NO. 1 BLACK OUT TAPE


    B298009E01
  1. Remove the portion of the new No. 1 black out tape at the perforation as shown in the illustration.
    Text in Illustration 
    *A
    LH Side
    *B
    RH Side
    *a
    Perforation
    *b
    Remove
    *c
    Square
    *d
    Round



  1. Apply the new No. 1 black out tape to the positions shown in the illustration.


    B298006E01


    Text in Illustration 
    *1
    Edge of curved surface
    -
    -

    Standard Measurement:
    Dimension
    Measurement
    a
    - 1.0 to 1.0 mm (- 0.0394 to 0.0394 in.)
    b
    2.0 mm (0.0787 in.)
    c
    1.0 mm (0.0394 in.)
    d
    3.0 mm (0.118 in.)
    e
    3.0 mm (0.118 in.)



4. INSTALL FRONT DOOR PANEL CUSHION


    B307112
  1. Engage each claw to Install the 2 cushions onto the door panel.



5. INSTALL FRONT DOOR LOCK OPEN ROD


    B307113E01
  1. Install the front door lock open rod as indicated by the arrows, in the order shown in the illustration.



6. INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
  1. Apply MP grease to the sliding parts on the front door outside handle frame sub-assembly.



    B312743
  1. Engage the guide and 2 clamps.

  1. Temporary install the front door outside handle frame sub-assembly to the front door.



    B307114E01
  1. Engage the door handle nut and 2 claws.
    Text in Illustration 
    *a
    Outside
    *b
    Inside

  1. Using a T30 "TORX" socket wrench, install the front door outside handle frame sub-assembly with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



7. INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY


    B307115
  1. Install the front door inside locking cable assembly as shown in the illustration.



    B307116
  1. Engage the 3 claws as shown in the illustration.



8. INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    B307117
  1. Install the front door lock remote control cable assembly as shown in the illustration.



9. INSTALL FRONT DOOR LOCK ASSEMBLY

NOTICE:
  1. When reusing the removed front door lock assembly, replace the door lock wiring harness seal on the connector with a new one.
  2. Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.
  3. Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the front door lock assembly.

  1. Apply MP grease to the sliding parts of the front door lock assembly.



  1. When reusing the front door lock assembly:



      B307105
    1. Install a new door lock wiring harness seal to the front door lock assembly.



    B307118E01
  1. Insert the front door lock open rod to the front door lock assembly.
    Text in Illustration 
    *1
    Front Door Lock Open Rod

    HINT:
    Make sure that the front door lock open rod is securely connected to the front door lock assembly.

  1. Using a T30 "TORX" socket wrench, install the front door lock assembly with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the connector.



10. INSTALL FRONT DOOR OUTSIDE HANDLE REAR PAD


    B307103
  1. Engage the 2 claws to install the front door outside handle rear pad.



11. INSTALL FRONT DOOR OUTSIDE HANDLE FRONT PAD


    B307102
  1. Engage the 3 claws to install the front door outside handle front pad.



12. INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY


    B307119
  1. Insert the front end of the front door outside handle assembly into the front door outside handle frame.

  1. Insert the rear end of the front door outside handle assembly into the front door outside handle frame, then slide the front door outside handle assembly toward the front of the vehicle to install it.



    B307120
  1. Connect the connector.

  1. Engage the 3 claws.



13. INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)


    B308298
  1. Engage the 2 guides and claw to install the front door outside handle cover to the front door lock cylinder.



14. INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)


    B300049
  1. Using a T30 "TORX" socket wrench, install the front door outside handle cover with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



    B297584
  1. Install the hole plug.



15. INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)


    B307098
  1. Install the front door outside handle cover with lock cylinder assembly.

    HINT:
    Make sure that the front door lock cylinder rod is inserted into the front door lock assembly.

  1. Using a T30 "TORX" socket wrench, install the front door lock cylinder with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }



    B299844
  1. Install the hole plug.



16. INSTALL FRONT DOOR FIX WINDOW WEATHERSTRIP
  1. Install the front door fix window glass onto the front door fix window weatherstrip.



    B307121
  1. Install the front door fix window weatherstrip with the front door fix window glass.



17. INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY


    B307096
  1. Temporary install the front door front lower frame sub-assembly with the 2 bolts.

  1. Install the screw.

  1. Tighten the 2 bolts to install the front door front lower frame sub-assembly.



18. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    B307095
  1. Engage the guide.

  1. Install the front door rear lower frame sub-assembly with the bolt.



19. INSTALL FRONT DOOR WEATHERSTRIP


    B307094
  1. Engage the 30 clips to install the front door weatherstrip.



20. INSTALL FRONT DOOR CHECK ASSEMBLY
  1. Apply MP grease to the sliding areas of the front door check assembly.



    B307093E03
  1. Apply adhesive to the threads of the bolt (A).

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the front door check assembly with the 3 bolts.

    Torque:
    Bolt (A):
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }
    Bolt (B):
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



21. INSTALL FRONT DOOR GLASS RUN


    B307092
  1. Install the front door glass run.



22. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY

NOTICE:
The regulator arm must be below the intermediate position when installing the power window regulator motor.



    B307091
  1. Using a T25 "TORX" socket wrench, install the power window regulator motor assembly with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    HINT:
    A new front window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.



23. INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY
  1. Apply MP grease to the sliding parts of the front door window regulator assembly.

  1. Install the temporary bolt to the front door window regulator assembly.



    B307122E01
  1. Temporarily install the front door window regulator assembly.
    Text in Illustration 
    *1
    Temporary Bolt

  1. Tighten the temporary bolt and 5 bolts.

    HINT:
    Tighten the bolts in the order shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



24. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
  1. Connect the cable to the negative (-) auxiliary battery terminal and power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal and power window regulator master switch.



    B307123
  1. Insert the front door glass sub-assembly into the front door panel along the front door glass run as shown in the illustration.

    NOTICE:
    Do not damage the front door glass.



    B307088
  1. Install the front door glass sub-assembly with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    B307087
  1. Install the front door No. 2 service hole cover.



25. INSTALL FRONT DOOR SERVICE HOLE COVER
  1. Apply new butyl tape to the front door panel.

  1. Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.



    B313978E01
  1. Attach the front door service hole cover according to the reference points on the front door panel.
    Text in Illustration 
    *a
    Reference Point

    HINT:
    Securely install the front door service hole cover preventing wrinkles and air bubbles.



26. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY


  1. Using an air riveter or a hand riveter, install the front No. 1 speaker assembly with 3 new rivets.


    E244888E01


    Text in Illustration 
    *1
    Riveter
    *2
    Mandrel
    *a
    INCORRECT
    *b
    CORRECT

    NOTICE:
    1. Do not touch the cone part of the speaker.
    2. Do not pry on the rivets with the riveter, as this will cause damage to the riveter and mandrel.
    3. Confirm that the rivets are seated properly against the speaker.
    4. Do not tilt the riveter when installing the rivets to the speaker.
    5. Do not leave any clearance between the rivet heads and speaker.
    6. Do not leave any clearance between the speaker and door. Firmly hold the 2 items together while installing the rivets.

    HINT:
    1. Install the rivets in the order shown in the illustration.
    2. If the rivet cannot be cut, pull it once and cut it.

  1. Connect the connector.



27. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY
  1. Install the front No. 2 speaker assembly with the 2 screws.

    NOTICE:
    Do not touch the cone part of the speaker.

  1. Connect the connector.



28. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER
  1. Engage the claw to install the outer rear view mirror assembly with cover with the 3 screws.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

  1. Connect the connector.



29. INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP


    B307125
  1. Engage the 8 claws to install the front door glass inner weatherstrip as shown in the illustration.



30. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


    B307084
  1. Engage the 4 guides to install the front door inside handle sub-assembly.



31. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    B307126E02
  1. Connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door inside handle.
    Text in Illustration 
    *1
    Front Door Inside Locking Cable Assembly
    *2
    Front Door Lock Remote Control Cable Assembly



    B307169
  1. Engage the 8 clips.



    B307081
  1. Install the front door trim board sub-assembly with the 3 screws.



    B307127
  1. Engage the claw and close the cover.



32. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)
  1. Connect the connector.



    B307078
  1. Engage the 4 guides and 10 claws to install power window regulator master switch assembly with front door armrest base panel.



33. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
  1. Connect the connector.



    B307079
  1. Engage the 4 guides and 10 claws to install power window regulator switch assembly with front door armrest base panel.



34. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here)



35. INSTALL FRONT FLOOR COVER RH
  1. Engage the 3 guides.



    B301488E01
  1. Engage the clip <B> to install the front floor cover RH.

  1. Install the 2 clips <A>.



36. INITIALIZE POWER WINDOW CONTROL SYSTEM (for Driver Side)
(Click here)


37. INSPECT POWER WINDOW OPERATION
(Click here)