Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Entry Function)

SMART ENTRY AND START SYSTEM (for Entry Function) > All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate

for Preparation Click here


DESCRIPTION

When the entry operation and wireless operation of the door lock functions do not operate, a malfunction or wave interference may be occurring in either of the following: 1) the signal communication line between the door control receiver and certification ECU (smart key ECU assembly) (the line used for entry and wireless operations); or 2) the electrical key transmitter sub-assembly. If the entry lock and wireless lock operations cannot be performed, there may be electrical key transmitter sub-assembly malfunctions, wave interference or problems in the communication which is used for the entry and wireless function between the door control receiver and certification ECU (smart key ECU assembly).

WIRING DIAGRAM


B392604E01


INSPECTION PROCEDURE

NOTICE:
  1. The smart entry and start system (for Entry Function) uses the CAN communication system and LIN communication system. First inspect the communication systems by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
  2. When using the intelligent tester with the power switch off to troubleshoot:
    Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
  3. Check that there are no electrical key transmitter sub-assemblies in the vehicle.
  4. Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (Click here).
  5. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  6. Before replacing the certification ECU (smart key ECU assembly) or electrical key transmitter sub-assembly, refer to the smart entry and start system (for Entry Function) precaution (Click here).
  7. After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
  8. The door control receiver has a constant voltage (5 V) supply circuit connected to terminal "+5".

1.INSPECT AUXILIARY BATTERY VOLTAGE
  1. Measure the voltage of the vehicle auxiliary battery.

    Standard voltage:
    11 to 14 V (IG OFF)

    HINT:
    It may be possible to tell whether the vehicle auxiliary battery is discharged by operating the horn.

    1. If the voltage is below 11 V, recharge or replace the vehicle auxiliary battery before proceeding.


NEXT


2.CHECK FOR DTC
  1. Open the driver door using the mechanical key built into the electrical key transmitter sub-assembly.

  1. Connect the intelligent tester and check for DTCs (Click here).

    HINT:
    When using the intelligent tester with the power switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

    OK:
    DTC is not output.



NG
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
OK


3.CHECK POWER DOOR LOCK CONTROL SYSTEM
  1. When the door control switch on the multiplex network master switch assembly on the driver door is operated, check that the doors unlock and lock according to the switch operation (Click here).

    OK:
    Door locks operate normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


4.CHECK KEY DIAGNOSTIC MODE


  1. Check the following antennas in the key diagnostic mode (Click here).



      B300377E01
    1. Check the electrical key antenna (for driver door):
      Text in Illustration 
      *A
      for LHD
      *B
      for RHD
      *a
      0.7 to 1 m (2.30 to 3.28 ft.)
      When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless door lock buzzer sounds.



    2. B300378E01
    3. Check the electrical key antenna (for front passenger door):
      Text in Illustration 
      *A
      for LHD
      *B
      for RHD
      *a
      0.7 to 1 m (2.30 to 3.28 ft.)
      When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for front passenger door), check that the wireless door lock buzzer sounds.



    4. B296517E01
    5. Check the No. 1 indoor electrical key antenna (front floor):
      Text in Illustration 
      *a
      Inspection Point
      When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.



    6. B300410E01
    7. Check the No. 2 indoor electrical key antenna (steering column):
      Text in Illustration 
      *A
      for LHD
      *B
      for RHD
      *a
      Inspection Point
      When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.



    8. B296518E01
    9. Check the No. 3 indoor electrical key antenna (rear floor):
      Text in Illustration 
      *a
      Inspection Point
      When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.



    10. B296538E02
    11. Check the electrical key antenna (outside luggage):
      Text in Illustration 
      *a
      0.7 to 1 m (2.30 to 3.28 ft.)
      When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage), check that the wireless door lock buzzer sounds.

      OK:
      Wireless door lock buzzer sounds.

      Result:
      Result
      Proceed to
      Diagnostic mode inspections fail
      A
      Diagnostic mode inspections succeed
      B



B
Go to step 10
A


5.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
  1. Check if there are any other registered electrical key transmitter sub-assemblies.

    Result:
    Result
    Proceed to
    There are no other registered electrical key transmitter sub-assemblies
    A
    There is another registered electrical key transmitter sub-assemblies
    B



B
Go to step 7
A


6.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
  1. Register a new electrical key transmitter sub-assembly.

    HINT:
    Refer to the Service Bulletin.


NEXT


7.CHECK ENTRY DOOR LOCK OPERATION
  1. Using another or newly registered electrical key transmitter sub-assembly, check if an entry lock/unlock operation can be performed twice in succession.

    OK:
    Entry lock/unlock operate normally twice.



NG
Go to step 10
OK


8.CHECK TRANSMITTER BATTERY
  1. Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.

    1. Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.

      Result:
      Result
      Proceed to
      Transmitter LED does not illuminate when switch is pressed and held
      A
      Transmitter LED illuminates 3 times or more when switch is pressed and held
      B
      Transmitter LED illuminates once or twice but not a third time
      C

      HINT:
      1. The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less (Click here).
      2. Even if the transmitter battery is depleted, it is still possible to start the hybrid system by holding the electrical key transmitter sub-assembly against the power switch, depressing the brake pedal and pressing the power switch.



B
REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

C
REPLACE TRANSMITTER BATTERY (Click here)
A


9.INSPECT TRANSMITTER BATTERY (VOLTAGE)


  1. Inspect the transmitter battery



      B197599E01
    1. Remove the transmitter battery from the electrical key transmitter sub-assembly that does not operate (Click here).

    2. Attach a lead wire (0.60 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal.
      Text in Illustration 
      *1
      Lead Wire

      NOTICE:
      Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.

    3. Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.



    4. B269082E01
    5. Measure the voltage of the transmitter battery.

      HINT:
      1. When measuring the transmitter battery voltage, bring the electrical key transmitter sub-assembly within the lock entry operating range while operating the lock sensor of a door handle to perform the measurement.
      2. Perform the measurement when the key is at room temperature.
      3. The key sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. When this voltage is 2.2 V or less the Data List item "Key Low Battery" displays "Yes". (Click here)

      Text in Illustration 
      *1
      GND

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      Transmitter battery positive (+) - Transmitter battery negative (-)
      Power switch off, all doors closed and lock sensor touched
      2.3 to 3.2 V



NG
REPLACE TRANSMITTER BATTERY (Click here)
OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY 

10.CHECK WAVE ENVIRONMENT
  1. Bring the electrical key transmitter sub-assembly near the door control receiver and perform a wireless and entry function operation check.

    HINT:
    1. When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
    2. If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
    3. There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
    4. If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.

    OK:
    Wireless and entry functions operate normally.



NG
Go to step 11
OK

AFFECTED BY WAVE INTERFERENCE 

11.READ VALUE USING INTELLIGENT TESTER (ACC SW, IG SW)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.


Main Body 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
ACC SW
Power switch status / ON or OFF
ON: Power switch on (ACC)
OFF: Power switch off
-
IG SW
Power switch status / ON or OFF
ON: Power switch to ON
OFF: Power switch off
-

HINT:
If the certification ECU (smart key ECU assembly) misjudges that the power source is on even though the power source is off for any reason, the entry lock/unlock functions stop.

OK:
The main body ECU (multiplex network body ECU) judges properly that the power source is off when the power source is off.



NG
TROUBLESHOOT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK


12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - AUXILIARY BATTERY AND BODY GROUND)


    B274828E12
  1. Disconnect the G77 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    G77-11 (E) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:

    Tester Connection
    Condition
    Specified Condition
    G77-10 (CUTB) - Body ground
    Always
    11 to 14 V
    G77-2 (+B) - Body ground
    Always
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR CONTROL RECEIVER)
  1. Disconnect the G78 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the M15 door control receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
G78-5 (RCO) - M15-4 (+5)
Always
Below 1 Ω
G78-17 (RDAS) - M15-5 (DATA)
Always
Below 1 Ω
G78-19 (RSSI) - M15-2 (RSSI)
Always
Below 1 Ω
G78-5 (RCO) or M15-4 (+5) - Body ground
Always
10 kΩ or higher
G78-17 (RDAS) or M15-5 (DATA) - Body ground
Always
10 kΩ or higher
G78-19 (RSSI) or M15-2 (RSSI) - Body ground
Always
10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.CHECK DOOR CONTROL RECEIVER (GND)


    B274836E23
  1. Connect the M15 door control receiver connector.

  1. Connect the G78 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M15-1 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Door Control Receiver)



NG
REPLACE DOOR CONTROL RECEIVER (Click here)
OK


15.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
B274836E24
  1. Connect the G78 certification ECU (smart key ECU assembly) connector.

  1. Connect the M15 door control receiver connector.

  1. Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Condition
Specified Condition
M15-4 (+5) - M15-1 (GND)
Procedure:
  1. Power switch off
  2. Electrical key transmitter sub-assembly switch not pressed
Below 1 V
Procedure:
  1. Power switch off
  2. Electrical key transmitter sub-assembly switch pressed
4.5 to 5.5 V

Text in Illustration 
*a
Component with harness connected
(Door Control Receiver)


NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK


16.CHECK DOOR CONTROL RECEIVER
B274836E25
  1. Connect the G78 certification ECU (smart key ECU assembly) connector.

  1. Connect the M15 door control receiver connector.

  1. Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Condition
Specified Condition
M15-5 (DATA) - M15-1 (GND)
Procedure:
  1. All doors closed
  2. All doors locked
  3. Electrical key transmitter sub-assembly switch pressed
Below 2 V → 11 to 14 V → Below 2 V
M15-2 (RSSI) - M15-1 (GND)
Procedure:
  1. Power switch off
  2. All doors closed
11 to 14 V → Below 2 V

Text in Illustration 
*a
Component with harness connected
(Door Control Receiver)


NG
REPLACE DOOR CONTROL RECEIVER (Click here)
OK


17.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Temporarily replace the certification ECU (smart key ECU assembly) with a new one.

    HINT:
    Refer to the Service Bulletin.


NEXT


18.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
  1. Check that the wireless door lock functions operate normally (Click here).

    OK:
    Wireless door lock functions operate normally.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)