Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL (for RHD)

BRAKE PEDAL (for RHD) > INSTALLATION

for Preparation Click here



1. INSTALL BRAKE PEDAL SUPPORT ASSEMBLY
  1. Install the brake pedal support assembly with the 4 nuts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Engage the wire harness clamp to install it to the stud bolt of the brake booster with master cylinder assembly.

  1. Install the bolt to secure the brake pedal support assembly to the instrument panel reinforcement assembly.

    Torque:
    24 N*m{ 241 kgf*cm , 17 ft.*lbf }

  1. Engage the clamp to the brake pedal support assembly.



2. INSTALL PUSH ROD PIN


    C251262
  1. Apply lithium soap base glycol grease to the push rod pin and installation hole of the brake pedal sub-assembly.
    Text in Illustration 
    V100145
    Lithium Soap Base Glycol Grease

  1. Install the push rod pin and a new clip to connect the push rod clevis to the brake pedal support assembly.

    NOTICE:
    Insert the push rod pin in the correct direction.



3. INSTALL BRAKE PEDAL RETURN SPRING
  1. Install the brake pedal return spring to the brake pedal support assembly.



4. INSTALL STOP LIGHT SWITCH MOUNTING ADJUSTER


5. INSTALL STOP LIGHT SWITCH ASSEMBLY


    E167768
  1. Insert the stop light switch assembly until the threaded sleeve hits the pedal.

    NOTICE:
    When inserting the stop light switch assembly, support the pedal from behind so that the pedal is not pushed in.



    E236346E01
  1. Make a quarter turn clockwise to install the stop light switch assembly.

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf } or less

    NOTICE:
    When inserting the stop light switch assembly, support the pedal from behind so that the pedal is not pushed in.

  1. Connect the connector.

  1. Check the protrusion of the plunger.
    Protrusion of Plunger 
    Area
    Measurement
    a
    0.5 to 2.6 mm (0.0197 to 0.102 in.)
    If the protrusion is not as specified, recheck switch installation and inspect brake pedal adjustment if necessary (Click here for LHD or Click here for RHD).

    NOTICE:
    Do not depress or support the brake pedal.



6. INSTALL BRAKE PEDAL STROKE SENSOR ASSEMBLY

NOTICE:
  1. Do not drop the brake pedal stroke sensor assembly.
  2. If the brake pedal stroke sensor assembly has been dropped, replace the brake pedal stroke sensor assembly with a new one.



  1. When installing a new brake pedal stroke sensor assembly:

    NOTICE:
    Do not break the brake pedal stroke sensor assembly lever set pin before installing the brake pedal stroke sensor assembly with the bolt.




      C249815E01
    1. Install a new brake pedal stroke sensor assembly to the brake pedal support assembly with the 2 bolts.
      Text in Illustration 
      *1
      Brake Pedal Stroke Sensor Assembly Lever
      *a
      Brake Pedal Groove

      Torque:
      8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

      NOTICE:
      1. Engage the brake pedal stroke sensor assembly lever with the brake pedal groove.
      2. Check that there is no foreign matter attached to the contact surface of the brake pedal stroke sensor assembly.
      3. Check that the tip of the brake pedal stroke sensor assembly lever is protruding from the brake pedal groove.

    2. Connect the connector.

    3. Firmly depress the brake pedal and break the brake pedal stroke sensor assembly lever set pin.

    4. Remove the broken lever set pin.



  1. When reusing the brake pedal stroke sensor assembly:



      C249815E01
    1. Install the brake pedal stroke sensor assembly to the brake pedal support assembly and temporarily tighten the 2 bolts.
      Text in Illustration 
      *1
      Brake Pedal Stroke Sensor Assembly Lever
      *a
      Brake Pedal Groove

      NOTICE:
      1. Engage the brake pedal stroke sensor assembly lever with the brake pedal groove.
      2. Check that there is no foreign matter attached to the contact surface of the brake pedal stroke sensor assembly.
      3. Check that the tip of the brake pedal stroke sensor assembly lever is protruding from the brake pedal groove.

      HINT:
      Fully tighten the 2 bolts when adjusting the brake pedal stroke sensor assembly.

    2. Connect the connector.



7. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

HINT:
Use the same procedure for LHD and RHD .



8. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL



9. INSPECT AND ADJUST BRAKE PEDAL
(Click here)


10. PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE
(Click here)