FUEL LID LOCK CONTROL CABLE ASSEMBLY (for LHD) > REMOVAL |
| 1. REMOVE FRONT SEAT ASSEMBLY LH |
| 2. REMOVE REAR SEAT HEADREST ASSEMBLY |
| 3. REMOVE REAR CENTER SEAT HEADREST ASSEMBLY |
| 4. REMOVE FRONT FLOOR COVER RH |
![]() |
Using a clip remover, remove the 2 clips <A>.
Disengage the 3 clips <B>.
![]() |
Disengage the 3 guides and remove the front floor cover RH.
| 5. REMOVE FRONT FLOOR COVER LH |
![]() |
Using a clip remover, remove the 2 clips <A>.
Disengage the 3 clips <B>.
![]() |
Disengage the 3 guides and remove the front floor cover LH.
| 6. REMOVE FRONT CENTER FLOOR COVER |
![]() |
Using a clip remover, remove the 3 clips.
Disengage the 2 guides and remove the front center floor cover.
| 7. REMOVE REAR SEATBACK ASSEMBLY LH |
Fold down the rear seatback assembly LH.
![]() |
Remove the 2 bolts and rear seatback assembly LH.
| 8. REMOVE REAR SEAT CUSHION ASSEMBLY |
![]() |
Disengage the 2 clips.
| *a | RH Side |
| *b | LH Side |
![]() |
Disengage the hook of the rear seat cushion assembly from the vehicle body as shown in the illustration.
| a | 100 mm (3.94 in.) or less |
Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.
Repeat the step above for the other hook.
Remove the rear seat cushion assembly.
| 9. REMOVE FRONT DOOR SCUFF PLATE LH |
![]() |
Disengage the 8 claws and remove the front door scuff plate LH.
| 10. REMOVE COWL SIDE TRIM BOARD LH |
![]() |
Remove the clip.
Disengage the clip and remove the cowl side trim board LH.
| 11. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
Disconnect the front door opening trim weatherstrip LH.
| 12. REMOVE REAR DOOR SCUFF PLATE LH |
![]() |
Disengage the 5 claws and guide and remove the rear door scuff plate LH.
| 13. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH |
Disconnect the rear door opening trim weatherstrip LH.
| 14. REMOVE CENTER PILLAR LOWER GARNISH LH |
![]() |
Disengage the 4 claws and 2 clips, and remove the center pillar lower garnish LH.
| 15. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY |
Remove the package tray trim panel assembly.
| 16. REMOVE DECK BOARD ASSEMBLY |
Remove the deck board assembly.
| 17. REMOVE DECK FLOOR BOX LH |
Remove the deck floor box LH.
| 18. REMOVE DECK FLOOR BOX RH |
| 19. REMOVE REAR DECK TRIM COVER |
![]() |
Remove the 2 clips.
Disengage the 4 claws and 2 guides, and remove the rear deck trim cover.
| 20. DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH |
![]() |
Remove the bolt and disconnect the shoulder anchor of the rear seat 3 point type outer belt assembly.
![]() |
Remove the bolt.
Disengage the 2 guides and remove the rear seat 3 point type outer belt assembly.
| 21. REMOVE REAR ABSORBER CAP LH |
![]() |
Disengage the 2 claws and 2 guides, and remove the rear absorber cap LH.
| 22. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY |
![]() |
Using a screwdriver with its tip wrapped with protective tape, disengage the claw.
| *1 | Protective Tape |
Disconnect the connector and remove the No. 1 luggage compartment light assembly.
| 23. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH |
Turn the rear seatback hinge in the direction indicated by the arrow shown in the illustration.

| *1 | Rear Seatback Hinge | - | - |
Remove the bolt and 2 screws.
Disengage the 4 claws, 4 clips and guide, and remove the deck trim side panel assembly LH.
| 24. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY |
![]() |
Remove the bolt.
Slide the fuel lid lock open lever sub-assembly as indicated by the arrow as shown in the illustration.
![]() |
Disengage the guide and remove the fuel lid lock open lever sub-assembly.
| 25. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY |
![]() |
Disengage the 2 claws and separate the fuel lid lock control cable sub-assembly.
Disengage the fuel lid lock control cable sub-assembly from clamps as shown in the illustration.

| *1 | Fuel Lid Lock Control Cable Sub-assembly | *2 | Wire Harness Clamp |
| *3 | Clamp of Fuel Lid Lock Control Cable Sub-assembly | - | - |
Disengage the clamp of fuel lid lock control cable sub-assembly to remove it.