Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for RHD)

BRAKE BOOSTER (for RHD) > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (Click here).



2. DISABLE BRAKE CONTROL
  1. Wait at least 2 minutes after turning the power switch off.

    NOTICE:
    When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off, the brake control system activates. Therefore do not depress the brake pedal or open/close the doors until the reservoir level switch connector is disconnected.



    C250008
  1. Disconnect the reservoir level switch connector with the parking brake applied.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal (Click here).

  1. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

  1. Check that the brake pedal can not be further depressed.

  1. Release the parking brake.



3. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
(Click here)


4. REMOVE INNER COWL TOP TO COWL BRACE


    C249834
  1. Remove the 3 bolts and inner cowl top to cowl brace.



5. REMOVE FRONT AIR SHUTTER SEAL


    C249836
  1. Disengage the clamp to remove the front air shutter seal.



6. REMOVE FRONT NO. 1 VENTILATOR SEAL


    C249835
  1. Disengage the clamp to remove the front No. 1 ventilator seal.



7. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY


    C256179
  1. Disengage the 3 clamps to separate the wire harness from the outer cowl top panel sub-assembly.



    C249838
  1. Remove the 8 bolts, nut and outer cowl top panel sub-assembly.



8. DRAIN BRAKE FLUID

NOTICE:
If brake fluid leaks onto any painted surface, immediately clean it off.



9. SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY


    C249839
  1. Remove the 2 nuts and separate the brake master cylinder reservoir assembly from the reservoir bracket.



10. DISCONNECT NO. 2 RESERVOIR HOSE


    C249840
  1. Move the clip and disconnect the No. 2 reservoir hose from the brake booster with master cylinder assembly.



11. DISCONNECT NO. 1 RESERVOIR HOSE


    C249842
  1. Move the clip and disconnect the No. 1 reservoir hose from the brake booster with master cylinder assembly.



12. SEPARATE NO. 2 BRAKE ACTUATOR HOSE


    C249844
  1. Move the clip and disconnect the No. 2 brake actuator hose from the No. 1 brake actuator tube.



13. REMOVE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY


14. REMOVE RESERVOIR BRACKET


    C249846
  1. Remove the bolt, nut and reservoir bracket.



15. REMOVE BRAKE PEDAL RETURN SPRING


    C249827
  1. Remove the brake pedal return spring from the brake pedal support assembly.



16. REMOVE PUSH ROD PIN


    C249828
  1. Remove the clip and push rod pin.

  1. Separate the push rod clevis from the brake pedal support assembly.



17. DISCONNECT BRAKE LINE


    C249848E01
  1. Using a union nut wrench, disconnect the 5 brake lines from the brake booster with master cylinder assembly.

  1. Use tags or make a memo to identify the places to reconnect the lines.
    Text in Illustration 
    *a
    to Front Wheel Cylinder LH
    *b
    to Rear Wheel Cylinder RH
    *c
    to Brake Booster Pump Assembly
    *d
    to Rear Wheel Cylinder LH
    *e
    to Front Wheel Cylinder RH



    C249851
  1. Disengage the brake tube clamp from the clamp bracket of the brake booster with master cylinder assembly.



18. REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY


    C249849
  1. Release the lock lever and disconnect the connector from the brake booster with master cylinder assembly.
    Text in Illustration 
    V100135
    Release the lock lever
    V100136
    Disconnect the connector



    C249829
  1. Disengage the wire harness clamp from the stud bolt of the brake booster with master cylinder assembly.



    C249831E01
  1. Remove the 4 nuts and brake booster with master cylinder assembly.
    Text in Illustration 
    *1
    Connector Portion
    *2
    Union
    *3
    Brake Master Cylinder Push Rod Clevis
    *4
    Boot
    *5
    Front No. 2 Brake Tube

    NOTICE:
    1. Do not kink or damage the brake lines.
    2. Do not carry the brake booster with master cylinder assembly by the portion shown in bold in the illustration.
    3. Be careful not to allow any brake fluid to enter the connector.



19. REMOVE BRAKE BOOSTER GASKET