Home › Drivetrain › P510 HYBRID TRANSMISSION / TRANSAXLE › HYBRID VEHICLE TRANSAXLE

HYBRID VEHICLE TRANSAXLE > INSTALLATION

for Preparation Click here



1. INSTALL TRANSAXLE HSG AND CASE WITH HEAD STRAIGHT SCREW PLUG
  1. Install a new gasket and the transaxle HSG and case with head straight screw plug to the hybrid vehicle transaxle assembly.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



2. INSTALL WIRE HARNESS CLAMP BRACKET
  1. Install the wire harness clamp bracket to the hybrid vehicle transaxle assembly with the bolt.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }



3. INSTALL TRANSMISSION CONTROL CABLE SUPPORT
  1. Install the 2 transmission control cable supports to the hybrid vehicle transaxle assembly with the 3 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



4. INSTALL MOTOR CABLE BRACKET
  1. Install the motor cable bracket to the transmission control cable support with the bolt.

    Torque:
    17 N*m{ 173 kgf*cm , 13 ft.*lbf }



5. INSTALL AUTOMATIC TRANSMISSION CASE COVER

HINT:
Perform this procedure only when replacement of the automatic transmission case cover is necessary.

  1. Install the automatic transmission case cover to the hybrid vehicle transaxle assembly with the 2 bolts.

    Torque:
    13 N*m{ 132 kgf*cm , 10 ft.*lbf }



6. INSTALL SHIFT LEVER POSITION SENSOR

HINT:
Perform this procedure only when replacement of the automatic transmission case cover is necessary.

  1. Install the shift lever position sensor to the manual valve shaft.

    NOTICE:
    1. Do not reuse the shift lever position sensor if it has been dropped or subjected to a severe impact.
    2. Do not allow moisture to adhere to the connector terminal.

  1. Temporarily install the 2 bolts.

  1. Install a new lock plate and tighten the nut.

    Torque:
    6.9 N*m{ 70 kgf*cm , 61 in.*lbf }

  1. Temporarily install the control shaft lever to the manual valve shaft.



    C250073E01
  1. Turn the lever clockwise until it stops, then turn it counterclockwise 2 notches.

  1. Remove the control shaft lever from the manual valve shaft.



    C256277E01
  1. Align the protruding part with the neutral basic line.
    Text in Illustration 
    *a
    Neutral Basic Line
    *b
    Protruding
    *c
    Range of Play

    NOTICE:
    There is play on the nut stopper side (protruding part). Align the center point of the range of the play with the neutral basic line.



    C256278E01
  1. Tighten the 2 bolts in the order shown in the illustration.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

  1. Using a screwdriver, secure the nut with the lock plate.



7. INSTALL TRANSMISSION CONTROL SHAFT LEVER
  1. Install the transmission control shaft lever, washer, and nut to the manual valve shaft.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }



8. INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET
  1. Install the No. 1 transmission control cable bracket to the hybrid vehicle transaxle assembly with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



9. INSTALL MOTOR CABLE

CAUTION:
Wear insulated gloves.



  1. Install the motor cable (for MG 1).

    1. Install the motor cable to the hybrid vehicle transaxle assembly with the 3 bolts.

      Torque:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }

      NOTICE:
      Keep the sealing surface of the generator cable and the connector terminal joint free of foreign matter.

    2. Engage the 2 claws to install a new terminal cap to the hybrid vehicle transaxle assembly.

      NOTICE:
      1. Keep foreign matter, water, etc. away from the terminal cap and its installation section.
      2. Do not pinch the O-ring.
      3. Check that the terminal cap is securely installed.



    3. C251935
    4. Place the connector shell in position and install it with the 2 bolts.

      Torque:
      19 N*m{ 196 kgf*cm , 14 ft.*lbf }



  1. Install the motor cable (for MG 2).

    1. Install the motor cable to the hybrid vehicle transaxle assembly with the 3 bolts.

      Torque:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }

      NOTICE:
      Keep the sealing surface of the generator cable and the connector terminal joint free of foreign matter.

    2. Engage the 2 claws to install a new terminal cap to the hybrid vehicle transaxle assembly.

      NOTICE:
      1. Keep foreign matter, water, etc. away from the terminal cap and its installation section.
      2. Do not pinch the O-ring.
      3. Check that the terminal cap is securely installed.



    3. C251936
    4. Place the connector shell in position and install it with the 2 bolts.

      Torque:
      19 N*m{ 196 kgf*cm , 14 ft.*lbf }

  1. Connect the 4 clamps and install the motor cable to the hybrid vehicle transaxle assembly.



10. INSTALL MOTOR COOLING PIPE ASSEMBLY
  1. Install a new O-ring and union to the hybrid vehicle transaxle assembly.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }



    C249803E01
  1. Temporarily tighten the motor cooling pipe assembly to the hybrid vehicle transaxle assembly with a new gasket and union bolt.
    Text in Illustration 
    *1
    Gasket
    *2
    Union Bolt
    *3
    Transaxle Case
    *a
    Stopper

  1. Install the oil cooler tube clamp and motor cooling pipe assembly to the No. 1 transmission control cable bracket with the bolt.

    Torque:
    12 N*m{ 117 kgf*cm , 8 ft.*lbf }

  1. Tighten the union bolt with the motor cooling pipe assembly stopper pressed against the transaxle case.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }

  1. Using a union nut wrench, connect the motor cooling pipe assembly to the union.

    Torque:
    34 N*m{ 350 kgf*cm , 25 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (Click here).

    HINT:
    Turn the flare nut while holding the union.



11. INSTALL HYBRID VEHICLE TRANSAXLE ASSEMBLY


    C249707E01
  1. Make sure that the knock pins are installed to the engine.
    Text in Illustration 
    *1
    Knock Pin

  1. Temporarily install the hybrid vehicle transaxle assembly to the engine with the 2 bolts.

    HINT:
    Temporarily tighten bolt B first.

  1. Fully tighten the 2 bolts in the order of A and B.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }

    NOTICE:
    1. Make sure that the wire harness or similar items are not pinched between the contact surfaces.
    2. Do not forcibly pry on the hybrid vehicle transaxle.
    3. Make sure to align the hybrid vehicle transaxle so that the input shaft of the hybrid vehicle transaxle will be inserted straight into the inner splines of the transmission input damper.
    4. Do not apply grease either to the spline or to the input shaft.
    5. When inserting the input shaft of the hybrid vehicle transaxle into the inner splines of the transmission input damper, do not shake the hybrid vehicle transaxle excessively.
    6. When mounting the hybrid vehicle transaxle to the engine, make sure to securely fit the knock pins into the knock holes.
    7. When tightening the bolts, be sure that the mating surfaces of the engine and the hybrid vehicle transaxle assembly are in close contact with one another.

    Bolt Length:
    45 mm (1.77 in.)



    C251452
  1. Install the 4 bolts.

    Torque:
    30 N*m{ 301 kgf*cm , 22 ft.*lbf }

    Bolt Length:
    45 mm (1.77 in.)

  1. Engage the claw and install the flywheel housing side cover to the engine.

  1. Install the starter hole heat insulator to the engine with the 2 bolts.

    Torque:
    30 N*m{ 301 kgf*cm , 22 ft.*lbf }

    Bolt Length:
    45 mm (1.77 in.)

  1. Install the drive shaft heat insulator bracket to the engine with the 2 bolts.

    Torque:
    30 N*m{ 301 kgf*cm , 22 ft.*lbf }

    Bolt Length:
    45 mm (1.77 in.)

  1. Connect the clamp to the drive shaft heat insulator bracket.

  1. Install the drive shaft heat insulator sub-assembly to the engine and drive shaft heat insulator bracket with the bolt and nut.

    Torque:
    18 N*m{ 179 kgf*cm , 13 ft.*lbf }



    C249795E02
  1. Install the 2 wire harness clamp brackets and transmission control cable clamp to the hybrid vehicle transaxle assembly with the 3 bolts.
    Text in Illustration 
    *1
    Wire Harness Clamp Bracket
    *2
    Transmission Control Cable Clamp

    Torque:
    Bolt A:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }
    Bolt B:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



12. INSTALL ENGINE MOUNTING BRACKET LH
  1. Clean and degrease the bolts and bolt holes.



    A192239E13
  1. Apply adhesive to 4 bolts.
    Text in Illustration 
    *1
    Adhesive

    NOTICE:
    Apply adhesive to the bolts and tighten them within 3 minutes of application.



    C251087E01
  1. Temporarily install the engine mounting bracket LH to the hybrid vehicle transaxle assembly with the 4 bolts.

    HINT:
    Temporarily tighten bolt D first.

  1. Fully tighten the 4 bolts in the order of A, B, C and D.

    Torque:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }

  1. Install the engine mounting insulator LH to the engine mounting bracket LH with the through bolt and nut.

    Torque:
    52 N*m{ 530 kgf*cm , 38 ft.*lbf }

    NOTICE:
    Turn the through bolt while holding the nut.



13. INSTALL ENGINE LATERAL CONTROL ROD


    C257213
  1. Temporarily tighten the engine lateral control rod to the hybrid vehicle transaxle assembly with the bolt.



    C256842E01
  1. Tighten the 4 bolts in the order shown in the illustration.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }



14. INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
  1. Support the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools.

    NOTICE:
    1. Make sure to secure the front suspension crossmember sub-assembly to prevent it from dropping.
    2. Use the attachments to keep the front suspension crossmember sub-assembly level.
    3. The front suspension crossmember sub-assembly is a heavy component. Make sure that it is supported securely.

  1. Temporarily tighten the front suspension crossmember sub-assembly to the body with the 6 bolts.



  1. Tighten the 2 bolts A and 2 bolts C on the left and right sides while alternately inserting SST into the left and right side reference holes in the front suspension crossmember sub-assembly.

    SST
    09670-00011  


    C249877E01


    Text in Illustration 
    *a
    OK
    *b
    NG
    V100136
    Front of the Vehicle
    -
    -

    Torque:
    Bolt A:
    87 N*m{ 887 kgf*cm , 64 ft.*lbf }
    Bolt C:
    98 N*m{ 999 kgf*cm , 72 ft.*lbf }

    NOTICE:
    Do not tighten bolt B to the specified torque. Bolt B will be fully tightened after the suspension is stabilized.

  1. Lower the engine lifter.

  1. Install the engine moving control rod with the bolt.

    Torque:
    120 N*m{ 1224 kgf*cm , 89 ft.*lbf }



15. REMOVE NO. 1 ENGINE HANGER
  1. Remove the 2 bolts and 2 No. 1 engine hangers.



16. INSTALL EGR VALVE ASSEMBLY

HINT:
After replacing the EGR valve assembly, perform the "Inspection After Repair" (Click here).

  1. Install a new gasket.

  1. Install the EGR valve assembly with the 2 bolts.

  1. Using an E8 "TORX" socket wrench, install the 2 stud bolts.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. Connect the No. 1 water by-pass hose.



    A266465
  1. Install the EGR valve bracket with the 2 bolts and nut.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. Connect the clamp and No. 5 water by-pass hose.

  1. Install the wire harness clamp bracket with the bolt.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }



    A267673
  1. Connect the 2 connectors and wire harness clamp.



17. INSTALL NO. 2 EGR PIPE


    A268229
  1. Install 2 new gaskets and the No. 2 EGR pipe with the 2 bolts and 2 nuts.

    Torque:
    Bolt:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    Nut:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    Make sure to tighten the 4 bolts evenly until the flanges of the EGR pipe assembly contact the installation surfaces.

  1. Connect the clamp and No. 2 water by-pass hose.

  1. Connect the wire harness clamp.



18. INSTALL FRONT DRIVE SHAFT ASSEMBLY
(Click here)


19. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    A077857
  1. Using a vernier caliper, measure the free length of the compression springs.
    Minimum
    41.5 mm (1.64 in.)

    HINT:
    If the free length is less than minimum, replace the compression spring.

  1. Fully insert a new gasket to the exhaust manifold converter sub-assembly.



    A181728E17
  1. Using a plastic hammer and wooden block, tap in the new gasket until its surface is flush with the exhaust manifold.
    Text in Illustration 
    *1
    Exhaust Manifold Converter Sub-assembly
    *2
    Gasket
    *3
    Wooden Block

    NOTICE:
    1. Be careful with the installation direction of the gasket.
    2. Do not reuse the gasket.
    3. Do not damage the gasket.
    4. Do not push in the gasket by using the exhaust pipe when connecting it.

  1. Connect the front exhaust pipe assembly to the 3 exhaust pipe supports.



  1. Install the front exhaust pipe assembly with the 2 bolts and 2 compression springs.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }


    HINT:
    A258941E01
    After installation, check that the gaps between the flanges of the exhaust manifold and front exhaust pipe assembly are consistent front-to-rear and left-to-right.
    Text in Illustration 
    *1
    Exhaust Manifold
    *2
    Front Exhaust Pipe Assembly
    *3
    Gasket
    *a
    Space between flanges: 8.5 mm (0.335 in.)



20. INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY


    C251686E02
  1. Place clip A as shown in the illustration and engage clip B to the body to connect the No. 1 steering column hole cover sub-assembly.
    Text in Illustration 
    *a
    Lip

    NOTICE:
    Make sure that the lip of the No. 1 steering column hole cover sub-assembly is not damaged.



21. INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY


    C232525E01
  1. Install the steering sliding yoke sub-assembly to the No. 2 steering intermediate shaft assembly.
    Text in Illustration 
    *a
    Matchmark

    NOTICE:
    Align the matchmarks on the steering sliding yoke sub-assembly and the No. 2 steering intermediate shaft assembly.

  1. Temporarily install the bolt.

    HINT:
    Fully tighten the bolt after installing the steering sliding yoke sub-assembly to the steering gear assembly.



22. INSTALL COLUMN HOLE COVER SILENCER SHEET


    C248046
  1. Install the column hole cover silencer sheet with the 2 clips.

  1. Install the floor carpet.



23. INSTALL WIRE HARNESS
  1. Connect the 7 clamps, 4 connectors and install the wire harness to the hybrid vehicle transaxle assembly with the 3 bolts.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Connect the 4 clamps and No. 2 engine wire.



24. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY
  1. Connect the transmission control cable assembly to the transmission control cable clamp and transmission control cable support.

  1. Connect the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.

  1. Install the transmission control cable assembly to the transmission control shaft lever with the nut.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



25. INSTALL INVERTER BRACKET ASSEMBLY

CAUTION:
Wear insulated gloves.

  1. Temporarily install the inverter bracket assembly with the 4 bolts.



    A268009E01
  1. Tighten the 4 bolts in the sequence shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the earth wire with the bolt.

    Torque:
    8.4 N*m{ 85 kgf*cm , 74 in.*lbf }

  1. Install the inverter reservoir tank assembly with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }



    A268006
  1. Connect the 2 wire harness clamps.



    A268005
  1. Connect the motor cable protector with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



26. INSTALL INVERTER WITH CONVERTER ASSEMBLY
(Click here)


27. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)


    C250015E01
  1. Install the outer cowl top panel sub-assembly with the 8 bolts and nut.

    Torque:
    Bolt:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }
    Nut:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Tighten the 2 bolts (1) and (2) first, and then tighten the rest of the bolts and nut.

  1. Engage the clamp to install the wire harness.



28. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)


    C249838E01
  1. Install the outer cowl top panel sub-assembly with the 8 bolts and nut.

    Torque:
    Bolt:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }
    Nut:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Tighten the 2 bolts (1) and (2) first, and then tighten the rest of the bolts and nut.

  1. Engage the 3 clamps to install the wire harness.



29. INSTALL FRONT NO. 1 VENTILATOR SEAL (for LHD)
  1. Engage the clamp to install the front No. 1 ventilator seal to the outer cowl top panel sub-assembly.



30. INSTALL FRONT NO. 1 VENTILATOR SEAL (for RHD)
  1. Engage the clamp to install the front No. 1 ventilator seal to the outer cowl top panel sub-assembly.



31. INSTALL FRONT AIR SHUTTER SEAL (for LHD)
  1. Engage the clamp to install the front air shutter seal to the outer cowl top panel sub-assembly.



32. INSTALL FRONT AIR SHUTTER SEAL (for RHD)
  1. Engage the clamp to install the front air shutter seal to the outer cowl top panel sub-assembly.



33. INSTALL INNER COWL TOP TO COWL BRACE (for LHD)


    C250011E01
  1. Install the inner cowl top to cowl brace to the outer cowl top panel sub-assembly with the 3 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

    NOTICE:
    Tighten the 3 bolts in the order shown in the illustration.



34. INSTALL INNER COWL TOP TO COWL BRACE (for RHD)


    C249834E01
  1. Install the inner cowl top to cowl brace to the outer cowl top panel sub-assembly with the 3 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

    NOTICE:
    Tighten the 3 bolts in the order shown in the illustration.



35. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
(Click here)


36. INSTALL HOOD SUB-ASSEMBLY
  1. Install the hood sub-assembly to the hood hinge assembly LH and hood hinge assembly RH with the 4 bolts.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }



37. INSPECT HOOD SUB-ASSEMBLY


  1. Check that the clearance measurements of areas "a" through "f" are within each standard range.


    B301498E02


    Standard Clearance 
    Area
    Measurement
    Area
    Measurement
    a
    -0.85 to 3.15 mm (-0.0335 to 0.124 in.)
    b
    1.65 to 5.65 mm (0.065 to 0.222 in.)
    c
    -1.85 to 2.15 mm (-0.0728 to 0.0847 in.)
    d
    2.35 to 6.35 mm (0.0925 to 0.25 in.)
    e
    2.0 to 5.0 mm (0.0787 to 0.197 in.)
    f
    -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)



38. ADJUST HOOD SUB-ASSEMBLY


  1. Horizontally and vertically adjust the hood.



      B301499
    1. Loosen the 4 hinge bolts of the hood.

    2. Adjust the clearance between the hood and front fender by moving the hood.

    3. Tighten the 4 hinge bolts after the adjustment.

      Torque:
      13 N*m{ 133 kgf*cm , 10 ft.*lbf }



  1. Adjust the height of the front end of the hood using the cushion rubbers.



      B297000
    1. Adjust the 2 cushion rubbers so that the heights of the hood and fender are aligned.

      HINT:
      Raise or lower the front end of the hood by turning the 2 cushion rubbers.



  1. Adjust the hood lock.



      B301500
    1. Loosen the 3 bolts.

    2. Tighten the bolts after adjustment.

      Torque:
      7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

    3. Check that the striker can engage with the hood lock smoothly.



39. INSTALL SERVICE PLUG GRIP
(Click here)


40. ADD COOLANT (for Engine)


    A267961E01
  1. Insert the engine drain cock plug.
    Text in Illustration 
    *1
    Hose

  1. Disconnect the hose from the engine drain cock plug.

  1. Install the stop ring.

  1. Tighten the radiator drain cock plug by hand.



    A206788E05
  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC) from the water filler. (Coolant level should be within 20 mm (0.787 in.) from the filler tube end.)
    Text in Illustration 
    *a
    Filler Tube End
    *b
    Coolant Level
    *c
    20 mm

    Standard Capacity:
    4.5 liters (4.8 US qts, 4 lmp. qts)

    NOTICE:
    Never use water as a substitute for engine coolant.

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).

  1. Remove the reserve tank cap.



    A275622E01
  1. Slowly pour coolant into the radiator reserve tank assembly until it reaches the full line.
    Text in Illustration 
    *a
    Full Line
    *b
    Low Line

  1. Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Install the water filler cap sub-assembly and reserve tank cap.

  1. Put the engine in inspection mode (Click here).

  1. Bleed air from the cooling system.

    NOTICE:
    1. Before starting the engine, turn the A/C switch off.
    2. Adjust the heater control to the maximum hot setting.
    3. Adjust the blower speed to the low setting.


    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by squeezing the No. 2 radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the hose.

    2. Squeeze the No. 1 and No. 2 radiator hoses several times by hand to bleed air.

      CAUTION:
      When squeezing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the cooling fan.

      NOTICE:
      1. Make sure that the radiator reserve tank assembly still has some coolant in it.
      2. If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.
      3. If there is not enough coolant, the engine may overheat or be seriously damaged.
      4. If the radiator reserve tank assembly does not have enough coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the reserve tank assembly is filled to the full line.

  1. Stop the engine and wait until the engine coolant cools down.

  1. Add engine coolant to the full line on the radiator reserve tank assembly.



41. ADD COOLANT (for Inverter)

NOTICE:
  1. Do not reuse the drained coolant because it may contain foreign matter.
  2. If the vehicle is driven with air in the inverter cooling system, damage may occur and the following DTCs may be stored.

    DTC Code
    Detection Item
    P0A01-726
    Motor Electronics Coolant Temperature Sensor Circuit Range / Performance
    P0A04-725
    Motor Electronics Coolant Temperature Sensor Circuit Intermittent
    P0A08-264
    DC / DC Converter Status Circuit
    P0A78-284
    Drive Motor "A" Inverter Performance
    P0A78-286
    Drive Motor "A" Inverter Performance
    P0A7A-322
    Generator Inverter Performance
    P0A7A-324
    Generator Inverter Performance
    P0A93-346
    Inverter Cooling System Performance
    P0A94-553
    DC / DC Converter Performance
    P0A94-557
    DC / DC Converter Performance
    P0AEE-277
    Motor Inverter Temperature Sensor "A" Circuit Range / Performance
    P0AF1-276
    Drive Motor Inverter Temperature Sensor "A" Circuit Intermittent / Erratic
    P0BCD-315
    Generator Inverter Temperature Sensor Circuit Range / Performance
    P0BD0-314
    Generator Inverter Temperature Sensor Circuit Intermittent / Erratic
    P0C39-626
    DC / DC Converter Temperature Sensor "A" Range / Performance
    P0C3C-625
    DC / DC Converter Temperature Sensor "A" Intermittent / Erratic
    P0C3E-628
    DC / DC Converter Temperature Sensor "B" Range / Performance
    P0C41-627
    DC / DC Converter Temperature Sensor "B" Intermittent / Erratic
    P0C73-776
    Motor Electronics Coolant Pump "A" Control Performance



    A266683
  1. Slowly pour coolant into the reserve tank until it reaches the full line.

    Coolant quantity:
    1.6 liters (1.7 US qts, 1.4 Imp. qts.)

    NOTICE:
    To prevent foreign matter such as dust or dirt from entering the cooling system, make sure to confirm that the container used to add coolant is clean and free of foreign matter such as dust or dirt.

  1. When using the intelligent tester:

    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.

    4. Keep the coolant at the full line in the reserve tank to compensate for the drop in coolant level when the air bleeds.

      Standard:
      Air bleeding from the inverter cooling system is completed when the noise made by the inverter water pump assembly becomes smaller and the circulation of coolant in the reserve tank improves.

      HINT:
      1. If free spinning of the inverter water pump is detected for approximately 5 seconds, fail-safe control will be activated to suspend the operation of the pump for approximately 15 seconds and resume operation for approximately 4 seconds repeatedly. Operation of the inverter water pump will return to normal if coolant is added.
      2. A loud noise made by the inverter water pump assembly and poor circulation of coolant in the reserve tank indicates that there is air in the cooling system.

  1. When not using the intelligent tester:

    1. Turn the power switch on (READY). [*1]

    2. Turn the power switch off and add coolant to the full line because the coolant level drops as the air bleeds. [*2]

      NOTICE:
      1. Be sure to turn the power switch off before adding SLLC.
      2. Do not work on the components in the engine compartment while the vehicle is in the READY-on state because the engine is in intermittent operation.

    3. Repeat steps [*1] and [*2] until air bleeding from the cooling system is completed.

      Standard:
      Air bleeding from the inverter cooling system is completed when the noise made by the inverter water pump assembly becomes smaller and the circulation of coolant in the reserve tank improves.

      HINT:
      A loud noise made by the inverter water pump assembly and poor circulation of coolant in the reserve tank indicates that there is air in the cooling system.

  1. After the air is completely bled from the cooling system, tighten the reserve tank cap.



    A266683
  1. Add coolant to the full line of the reserve tank.



42. ADD HYBRID TRANSAXLE FLUID


    C249713E01
  1. Add transaxle fluid until the fluid level is between 0 to 8 mm (0 to 0.315 in.) from the bottom lip of the filler plug opening.
    Text in Illustration 
    *1
    Filler Nozzle

    NOTICE:
    1. Stop the vehicle on a level surface.
    2. Use Toyota Genuine ATF WS.
    3. Be sure to fully insert the filler nozzle into the filler plug opening.
    4. Be sure to add fluid slowly. If fluid is added quickly, the fluid may hit internal parts and bounce back, resulting in fluid coming out of the filler plug opening.
    5. Be sure to directly check that the transaxle fluid level is within the specified range.
    6. Insufficient or excessive amounts of transaxle fluid may damage the hybrid transaxle.

    Reference:
    3.3 liters (3.5 US qts, 2.9 Imp. qts)

  1. After adding fluid, leave it for 30 seconds so that the fluid surface can become still again, and then check that the fluid level is between 0 to 8 mm (0 to 0.315 in.) from the bottom lip of the filler plug opening. (If the fluid level is too low, return to the Add Hybrid Transaxle Fluid procedure.)

    NOTICE:
    After adding fluid, make sure to check the fluid level.

  1. Using a 10 mm hexagon socket wrench, temporarily install the filler plug and gasket.

    HINT:
    Because the filler plug will be removed again, the gasket can be reused at this time.



43. INSPECT HYBRID TRANSAXLE FLUID


    C249714
  1. Using a 10 mm hexagon socket wrench, remove the filler plug and gasket.

  1. Check that the fluid level is between 0 to 8 mm (0 to 0.315 in.) from the bottom lip of the filler plug opening. (If the fluid level is too low, return to the Add Hybrid Transaxle Fluid procedure.)

    NOTICE:
    1. Stop the vehicle on a level surface.
    2. Be sure to directly check that the transaxle fluid level is within the specified range.
    3. Insufficient or excessive amounts of transaxle fluid may damage the hybrid transaxle.
    4. If the fluid was replaced or fluid was added, make sure to recheck the fluid level after driving the vehicle.

  1. Check for leaks if the quantity of transaxle fluid is low. (If there are no fluid leaks but the amount of the fluid is insufficient, add fluid .

  1. Using a 10 mm hexagon socket wrench, install the filler plug with a new gasket.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }



44. INSPECT FOR COOLANT LEAK (for Engine)

NOTICE:
Before performing each inspection, turn the A/C switch off.



    A268671
  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Put the engine in inspection mode (Click here).

  1. Warm up the engine.

  1. Using a radiator cap tester, increase the pressure inside the radiator to 108 kPa (1.1 kgf/cm2, 16 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator, engine water pump, front exhaust pipe assembly and engine coolant temperature sensor for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.



45. INSPECT FOR COOLANT LEAK (for Inverter)
  1. Remove the reserve tank cap.

    CAUTION:
    To avoid the danger of being burned, do not remove the reserve tank cap while the coolant for the inverter is still hot.



    A266680
  1. Install a radiator cap tester.

  1. Pump the radiator cap tester to 122 kPa (1.2 kgf/ cm2, 18 psi), and then check that the pressure does not drop.

    HINT:
    If the pressure drops, check the hoses, radiator, inverter water pump assembly, inverter with converter, and hybrid vehicle transaxle assembly for leaks.

  1. Reinstall the reserve tank cap.



46. INSPECT FOR HYBRID TRANSAXLE FLUID LEAK


47. INSPECT FOR EXHAUST GAS LEAK


48. INSTALL FRONT WHEELS

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



49. INSPECT SHIFT LEVER POSITION SENSOR POSITION
  1. Apply the parking brake.

  1. Lock the wheels with chocks to secure the vehicle.

  1. Turn the power switch on (READY).

  1. Move the shift lever to D and release the brake.

    NOTICE:
    Be sure to apply the parking brake and lock the wheels with chocks to secure the vehicle.



    C248512E01
  1. Slowly move the shift lever to N and measure moving distance (A) of the shift lever from the original point to the gear disengagement point.
    Text in Illustration 
    *a
    Gear Disengagement Point
    *b
    N Position
    *c
    R Position
    *d
    D Position

    NOTICE:
    Be sure to move the shift lever slowly.

  1. Move the shift lever to R and release the brake.

    NOTICE:
    Be sure to apply the parking brake and lock the wheels with chocks to secure the vehicle.

  1. Slowly move the shift lever to N and measure moving distance (B) of the shift lever from the original point to the vehicle disengagement point.

    NOTICE:
    Be sure to move the shift lever slowly.

  1. Check that moving distances (A) and (B) shown in the illustration are almost the same.

    HINT:
    1. If moving distances (A) and (B) are almost the same, adjustment of the shift lever position is not necessary.
    2. If moving distance (A) is shorter than (B), perform adjustment of the shift lever position [*1].
    3. If moving distance (B) is shorter than (A), perform adjustment of the shift lever position [*2].



50. ADJUST SHIFT LEVER POSITION SENSOR POSITION


  1. If moving distance (A) is shorter than (B). [*1]

    HINT:
    If the shift lever is moved from R to N, the moving distance of the shift lever from the original point to the gear disengagement point becomes longer.


    1. Move the shift lever to N.



    2. C256278
    3. Loosen the 2 bolts.



    4. C256279
    5. Slightly turn the shift lever position sensor counterclockwise.



    6. C256278E01
    7. Tighten the 2 bolts in the order shown in the illustration.

      Torque:
      13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    8. Recheck the shift lever position sensor.



  1. If moving distance (B) is shorter than (A). [*2]

    HINT:
    If the shift lever is moved from D to N, the moving distance of the shift lever from the original point to the gear disengagement point becomes longer.


    1. Move the shift lever to N.



    2. C256278
    3. Loosen the 2 bolts.



    4. C256280
    5. Slightly turn the shift lever position sensor clockwise.



    6. C256278E01
    7. Tighten the 2 bolts in the order shown in the illustration.

      Torque:
      13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    8. Recheck the shift lever position sensor.



51. INSPECT SHIFT LEVER POSITION
  1. While moving the shift lever from N to each position, check that the lever moves smoothly and that the shift position indicator comes on properly according to the shift lever position.

  1. Turn the power switch on (READY) and check the following:

    1. When the shift lever is moved to D, the vehicle moves forward.

    2. When the shift lever is moved to R, the vehicle moves in reverse.

      NOTICE:
      The vehicle should not move when the shift position indicator is off.



52. ADJUST SHIFT LEVER POSITION
  1. Apply the parking brake and move the shift lever to N.

  1. Remove the rear console box assembly (Click here).



    C258106E01
  1. Slide the adjuster case cover in the direction shown by the arrow.
    Text in Illustration 
    *1
    Adjuster Case
    *2
    Adjuster Case Cover



    C258107E01
  1. Using a precision screwdriver, pull out the lock piece of the adjuster case.
    Text in Illustration 
    *1
    Adjuster Case
    *2
    Lock Piece

  1. Using your fingers, gently pull the cable rod towards the rear of the vehicle to remove backlash.



    C258108E01
  1. Push in the lock piece of the adjuster case to lock it.
    Text in Illustration 
    *1
    Adjuster Case
    *2
    Lock Piece
    *3
    Cable Rod



    C258109E01
  1. Move the adjuster case cover in the direction shown by the arrow.
    Text in Illustration 
    *1
    Adjuster Case
    *2
    Lock Piece
    *3
    Adjuster Case Cover

    NOTICE:
    If the adjuster case cover is not moved far enough so that the adjuster case cover engages the lock piece, the cable will not be able to lock, and reliable shift operation will not be possible.

  1. Install the rear console box assembly (Click here).



53. INSTALL ENGINE UNDER COVER RH


54. INSTALL ENGINE UNDER COVER LH


55. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
(Click here)


56. CHECK ABS SPEED SENSOR SIGNAL
(Click here)