Home › Engine / Hybrid System › 1NZ-FXE ENGINE CONTROL › SFI SYSTEM

DTC    P060B    Internal Control Module A/D Processing Performance

for Preparation Click here


MONITOR DESCRIPTION

This DTC is stored when a communication error occurs in the ECM.

DTC No.
DTC Detection Condition
Trouble Area
P060B
An ECM main CPU communication error (1 trip detection logic).
  1. ECM
  2. Knock control sensor

MONITOR STRATEGY


Required Sensors/Components
ECM
Frequency of Operation
Continuous

CONFIRMATION DRIVING PATTERN

  1. Connect the intelligent tester to the DLC3.
  2. Turn the power switch on (IG) and turn the tester on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the tester off.
  5. Turn the power switch off.
  6. Disconnect the tester.
  7. Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.
  8. Connect the cable to the negative (-) auxiliary battery terminal.
  9. Connect the tester to the DLC3.
  10. Turn the power switch on (IG) and turn the tester on.
  11. Wait 16 seconds or more.
  12. Enter the following menus: Powertrain / Engine and ECT / DTC.
  13. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  14. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  15. Input the DTC: P060B.
  16. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.


INSPECTION PROCEDURE

NOTICE:
After turning power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ OUTPUT DTC (DTC P060B)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the power switch off and turn the tester off.

  1. Disconnect the tester.

  1. Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.

  1. Connect the cable to the negative (-) auxiliary battery terminal.

  1. Connect the tester to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the tester on.

  1. Wait 16 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P060B is output
    B
    DTC P060B and P0327, P0328 are output
    C



B
REPLACE ECM (Click here)

C
GO TO DTC P0327, P0328 (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)