Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING

ROOF HEADLINING > INSTALLATION

for Preparation Click here



1. INSTALL ROOF HEADLINING ASSEMBLY


    B301725
  1. Pull the roof headlining back into the vehicle through the back door.

    NOTICE:
    Do not damage the roof headlining assembly or vehicle interior.

  1. Engage the 2 claws.

  1. Install the roof headlining assembly with the 3 clips.

  1. for front pillar RH side:

    1. Engage the 3 clamps.

    2. Connect the connector.

  1. for front pillar LH side:

    1. Engage the 3 clamps.

    2. Connect the connector.

  1. for rear pillar RH side:

    1. Engage the 2 clamps.

    2. Connect the connector bracket with the bolt.

      Torque:
      8.4 N*m{ 86 kgf*cm , 74 in.*lbf }

    3. Connect the connector.



2. INSTALL VISOR HOLDER


    B211698
  1. Engage the 2 claws and turn the visor holder 45° counterclockwise to install it.

    HINT:
    Use the same procedure for the RH side and LH side.



3. INSTALL VISOR ASSEMBLY LH


    B322943
  1. Install the visor assembly LH with the 2 screws.

    HINT:
    Install the visor assembly LH with the arrow facing the front of the vehicle.

  1. Connect the visor shaft into the visor holder.



4. INSTALL VISOR ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



5. INSTALL ASSIST GRIP ASSEMBLY

HINT:
Use the same procedure to install all assist grips.



    B203057
  1. Assemble the front assist grip assembly as shown in the illustration.



    B229265
  1. Install the assist grip assembly.



6. INSTALL MAP LIGHT ASSEMBLY
  1. Connect the connector.



    E236389E01
  1. Engage the 4 claws to install the map light assembly.
    Text in Illustration 
    *a
    Contact Portion

    NOTICE:
    Do not touch the metal plates, especially the contact portions, as it may cause a malfunction such as the light does not illuminate.



7. INSTALL NO. 1 ROOM LIGHT ASSEMBLY (w/ Room Light)


    E252619E01
  1. Align the switch parts as shown in the illustration and engage the 4 claws to install the room light switch base to the No. 1 room light housing.
    Text in Illustration 
    *a
    Switch Part of Room Light Switch Base
    *b
    Switch Part of No. 1 Room Light Housing

  1. Engage the clamp.



    E252616E01
  1. Engage the 4 claws to install the No. 1 room light housing.
    Text in Illustration 
    *a
    Front



    E252617E01
  1. Engage the 4 claws to install the No. 1 room light lens.
    Text in Illustration 
    *a
    Front



8. INSTALL ROOF SIDE INNER GARNISH LH
  1. Pass the floor anchor of the rear seat 3 point type outer belt assembly LH through the roof side inner garnish LH.

  1. Engage the 5 clips to install the roof side inner garnish LH.



9. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH


  1. Engage the guide, 4 claws and 4 clips.


    B300800E02


    Text in Illustration 
    *a
    Rear Seatback Hinge
    -
    -

  1. Install the deck trim side panel assembly LH with the bolt and 2 screws.

  1. Turn the rear seatback hinge as shown in the illustration.



10. INSTALL REAR ABSORBER CAP LH
  1. Engage the 2 guides and 2 claws to install the rear absorber cap LH.



11. INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY
  1. Connect the connector.



    E288706
  1. Engage the claw to install the No. 1 luggage compartment light assembly.



12. CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH
  1. Engage the 2 claws.

  1. Install the floor anchor of the rear seat 3 point type outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



13. INSTALL ROOF SIDE INNER GARNISH RH
  1. Pass the floor anchor of the rear seat 3 point type outer belt assembly RH through the roof side inner garnish RH.

  1. Engage the 5 clips to install the roof side inner garnish RH.



    B297734
  1. Engage the guide and 4 claws to connect the belt guide.



14. CONNECT REAR CENTER SEAT LAP TYPE BELT ASSEMBLY
  1. Install the shoulder anchor of the rear center seat lap type belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 30 ft.*lbf }



    B300538
  1. Engage the 2 claws to close the cover as shown in the illustration.



15. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



16. INSTALL REAR ABSORBER CAP RH

HINT:
Use the same procedure as for the LH side.



17. INSTALL REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



18. INSTALL REAR DECK TRIM COVER
  1. Engage the 2 guides and 4 claws.

  1. Install the rear deck trim cover with the 2 clips.



19. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY
  1. Install the package tray trim panel assembly.



20. INSTALL DECK FLOOR BOX LH
  1. Install the deck floor box LH.



21. INSTALL DECK FLOOR BOX RH

HINT:
Use the same procedure as for the LH side.



22. INSTALL DECK BOARD ASSEMBLY
  1. Install the deck board assembly.



23. INSTALL CENTER PILLAR UPPER GARNISH LH
  1. Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar upper garnish LH.

  1. Engage the clip.

  1. Install the center pillar upper garnish LH with the 2 screws.



24. INSTALL CENTER PILLAR LOWER GARNISH LH
  1. Engage the 4 claws and 2 clips to install the center pillar lower garnish LH.



25. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
  1. Install the floor anchor of the front seat outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



26. INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)
  1. Engage the 3 claws and install the lap belt outer anchor cover.



27. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    B299875E01
  1. Align the alignment mark (White) on the weatherstrip with the flange on the vehicle body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
    Text in Illustration 
    *a
    Alignment Mark (White)
    *b
    Flange Position

    NOTICE:
    After installation, check that the corners fit correctly.



28. INSTALL FRONT PILLAR GARNISH LH
  1. Remove the protective cover.

  1. Make sure that the front pillar garnish clip is not damaged.

    NOTICE:
    If there is any damage, replace the garnish clip with a new one.



    E276148E01
  1. Push the front pillar garnish LH in the direction indicated by the arrow (1) shown in the illustration to engage the 2 guides.
    Text in Illustration 
    *a
    Protective Tape

  1. Using needle-nose pliers with the tips wrapped with protective tape, bend the end of the front pillar garnish clip in the direction indicated by the arrow (2) shown in the illustration.

  1. Push the front pillar garnish LH in the direction indicated by the arrow (3) shown in the illustration and insert it to the front pillar garnish clip.

  1. Using needle-nose pliers with the tips wrapped with protective tape, rotate the front pillar garnish clip in the direction indicated by the arrow (4) shown in the illustration.

    HINT:
    Rotate the front pillar garnish clip so that the longer end of the front pillar garnish clip is positioned at the bottom.

  1. Using needle-nose pliers with the tips wrapped with protective tape, push the front pillar garnish clip in the direction indicated by the arrow (5) and rotate it to the position shown in the illustration.

    HINT:
    Make sure that the front pillar garnish clip is positioned as shown in the illustration. Failing to do so may cause a gap between the front pillar garnish LH and roof headlining assembly.



    E276149E01
  1. Engage the clip and front pillar garnish clip to install the front pillar garnish LH.
    Text in Illustration 
    *1
    Front Pillar Garnish Clip

    NOTICE:
    If there is a gap between the front pillar garnish LH and roof headlining assembly, the front pillar garnish clip is not installed correctly. While lightly pressing the front pillar garnish LH as shown in the illustration, push it towards the front pillar garnish clip side.

    HINT:
    Make sure that the curtain shield airbag assembly LH is not pinched.



29. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    B299871E01
  1. Align the alignment mark (Yellow) on the weatherstrip with the flange on the vehicle body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
    Text in Illustration 
    *a
    Alignment Mark (Yellow)
    *b
    Flange Position

    NOTICE:
    After installation, check that the corners fit correctly.



30. INSTALL COWL SIDE TRIM BOARD LH
  1. Engage the clip.

  1. Install the cowl side trim board with the clip.



31. INSTALL FRONT DOOR SCUFF PLATE LH
  1. Engage the 8 claws to install the front door scuff plate.



32. INSTALL REAR DOOR SCUFF PLATE LH
  1. Engage the guide and the 5 claws to install the rear door scuff plate.



33. INSTALL CENTER PILLAR UPPER GARNISH RH

HINT:
Use the same procedure as for the LH side.



34. INSTALL CENTER PILLAR LOWER GARNISH RH

HINT:
Use the same procedure as for the LH side.



35. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.



36. INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:
Use the same procedure as for the LH side.



37. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B299873E01
  1. Align the alignment mark (Red) on the weatherstrip with the flange on the vehicle body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.
    Text in Illustration 
    *a
    Alignment Mark (Red)
    *b
    Flange Position

    NOTICE:
    After installation, check that the corners fit correctly.



38. INSTALL FRONT PILLAR GARNISH RH

HINT:
Use the same procedure as for the LH side.



39. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side.



40. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    B299869E01
  1. Align the alignment mark (Yellow green) on the weatherstrip with the flange on the vehicle body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
    Text in Illustration 
    *a
    Alignment Mark (Yellow green)
    *b
    Flange Position

    NOTICE:
    After installation, check that the corners fit correctly.



41. INSTALL COWL SIDE TRIM BOARD RH

HINT:
Use the same procedure as for the LH side.



42. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side.



43. INSTALL REAR SEAT ASSEMBLY (for Separate Type Seatback)
(Click here)


44. INSTALL REAR SEAT ASSEMBLY (for Bench Type Seatback)
(Click here)