Home › Vehicle Interior › HEATING / AIR CONDITIONING › CONDENSER

CONDENSER > REMOVAL

for Preparation Click here



1. RECOVER REFRIGERANT FROM AIR CONDITIONING SYSTEM
  1. Start the hybrid system.

  1. Operate the cooler compressor under the conditions show below:
    Item
    Condition
    Engine Speed
    Idling
    Operating Time
    3 minutes or more
    A/C Switch Status
    ON
    Blower Switch Status
    HI
    Set Temperature
    MAX COOL
    This causes most of the compressor oil from the various components of the A/C system to collect in the A/C compressor.

    HINT:
    It is not necessary to operate the cooler compressor if the A/C does not operate because of compressor lock, etc.

  1. Stop the engine.

  1. Recover the refrigerant from the A/C system using a refrigerant recovery unit.

    HINT:
    Use the refrigerant recovery unit in accordance with the manufacturer's instruction manual.



2. REMOVE FRONT BUMPER ASSEMBLY
(Click here)


3. REMOVE RADIATOR SUPPORT OPENING COVER


    B391888
  1. Remove the 4 clips and radiator support opening cover.



4. REMOVE NO. 2 RADIATOR SIDE AIR SEAL


    B307338
  1. Disengage the 2 claws and remove the No. 2 radiator side air seal.



5. REMOVE NO. 1 RADIATOR SIDE AIR SEAL


    B307339
  1. Disengage the 2 claws and remove the No. 1 radiator side air seal.



6. REMOVE RADIATOR SUPPORT EXTENSION LH


    B307340
  1. Disengage the 2 clamps and disconnect the thermistor assembly.

  1. Disengage the 2 claws and remove the radiator support extension LH.



7. REMOVE RADIATOR SUPPORT EXTENSION RH


    B307341
  1. Disengage the 2 claws and remove the radiator support extension RH.



8. REMOVE FRONT BUMPER ENERGY ABSORBER


    B310562
  1. Disengage the 2 guides to remove the front bumper energy absorber.



9. REMOVE FRONT BUMPER REINFORCEMENT


    B310563
  1. Disengage the 2 clamps and disconnect the wire harness.

  1. Remove the 6 bolts and front bumper reinforcement.



10. REMOVE HOOD LOCK ASSEMBLY


    B297001
  1. Remove the 3 bolts.



    B301501
  1. Disconnect the hood lock control cable and remove the hood lock assembly.



11. REMOVE HOOD LOCK SUPPORT SUB-ASSEMBLY


    E234966
  1. Disconnect the connector.

  1. Remove the 2 bolts and hood lock support sub-assembly.



12. REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY


    A267973
  1. Disconnect the horn connector.



    A267972
  1. Disconnect the 3 clamps and cooling fan ECU connector.



    A280343E01
  1. Disconnect the clamp of hood lock control cable.
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD



    A267979
  1. Remove the 5 bolts and upper radiator support sub-assembly.

  1. Remove the 2 radiator support cushions.



13. REMOVE NO. 2 FAN SHROUD


    A248164
  1. Remove the 2 bolts, 2 claws and No. 2 fan shroud.



14. DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE


    E234967
  1. Remove the bolt and disconnect the No. 1 cooler refrigerant discharge hose from the cooler condenser assembly.

  1. Remove the O-ring from the No. 1 cooler refrigerant discharge hose.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.



15. DISCONNECT LIQUID PIPE SUB-ASSEMBLY


    E238125
  1. Remove the bolt and disconnect the liquid pipe sub-assembly from the cooler condenser assembly.

  1. Remove the O-ring from the liquid pipe sub-assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent the entry of moisture and foreign matter.



16. REMOVE COOLER CONDENSER ASSEMBLY


    E234968
  1. Disengage the 2 guides and remove the cooler condenser assembly as shown in the illustration.

    NOTICE:
    Do not damage the condenser or radiator when removing the cooler condenser assembly.



17. REMOVE NO. 1 COOLER CONDENSER CUSHION


    E234987
  1. Remove the 4 No. 1 cooler condenser cushions from the cooler condenser assembly.