Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function)

DTC    U0293    Lost Communication with HV ECU

for Preparation Click here


DESCRIPTION

This DTC is stored when the power management control ECU detects a CAN communication error inside the power management control ECU (power control section - HV control section).

HINT:
When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
U0293
CAN communication error inside the power management control ECU (power control section - HV control section). (1-trip detection logic*)
  1. AM2 fuse
  2. Power management control ECU
  3. Wire harness or connector
Turn the power switch on (IG) and wait 10 seconds or more.
  1. *: Only detected while a malfunction is present.

Vehicle Condition and Fail-safe Function when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Function when Malfunction Detected
There is no effect on vehicle behavior.
-

WIRING DIAGRAM


B300415E02


INSPECTION PROCEDURE

NOTICE:
  1. When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:
    for Power Source Control: Body / Power Source Control / DTC.
    for Entry&Start: Body / Entry&Start / DTC.
  2. The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
  3. Before replacing the power management control ECU, refer to the Service Bulletin.
  4. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  5. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.


HINT:

Related Data List and Active Test Items 
DTC
Data List Item
Active Test Item
U0293
-
-

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
B223988E10
  1. Disconnect the G57 and G58 connectors from the power management control ECU.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G57-1 (AM22) - Body ground
    Power switch off
    11 to 14 V
    G58-7 (AM21) - Body ground
    Power switch off
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE
OK


2.CHECK HARNESS AND CONNECTOR (GROUND)
B223988E11
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G57-5 (E01) - Body ground
    Always
    Below 1 Ω
    G57-6 (E1) - Body ground
    Always
    Below 1 Ω
    G58-5 (E02) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs again.

    OK:
    DTC U0293 is not output



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK

END (USE SIMULATION METHOD TO CHECK) (Click here)