Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR (for Rear Door)

POWER WINDOW REGULATOR MOTOR (for Rear Door) > INSTALLATION

for Preparation Click here



1. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY

NOTICE:
The regulator arm must be below the intermediate position when installing the rear power window regulator motor assembly.



    B307149
  1. Using a T25 "TORX" socket wrench, install the power window regulator motor assembly with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    HINT:
    A new rear window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.



2. INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY
  1. Apply MP grease to the sliding parts of the rear door window regulator assembly.

  1. Install the temporary bolt to the rear door window regulator assembly.



    B307148E02
  1. Temporarily install the rear door window regulator assembly.
    Text in Illustration 
    *1
    Temporary Bolt

  1. Tighten the temporary bolt and 3 bolts to install the rear door window regulator assembly in the order shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.



3. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    B307174E01
  1. Insert the rear door glass as indicated by the arrows in the order shown in the illustration.

    NOTICE:
    Do not damage the rear door glass.

  1. Slide the lower section of the rear door glass sub-assembly and engage the rear door glass sub-assembly to the rear door window regulator assembly.



4. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    B307144
  1. Temporary install the rear door window division bar sub-assembly with the 2 bolts.

    NOTICE:
    Do not damage the rear door glass.

  1. Install the rear door window division bar sub-assembly with the 2 bolts and screw.



5. INSTALL REAR DOOR GLASS RUN


    B307143
  1. Install the rear door glass run.



6. CONNECT REAR DOOR WEATHERSTRIP
  1. Connect the upper part of rear door weatherstrip.



7. INSTALL REAR DOOR SERVICE HOLE COVER
  1. Apply butyl tape to the rear door panel.

  1. Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.



    B307175E01
  1. Attach the rear door service hole cover according to the reference points on the rear door panel.
    Text in Illustration 
    *a
    Reference Point

    NOTICE:
    Securely install the rear door service hole cover preventing wrinkles and air bubbles.



8. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B307178E01
  1. Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly to the rear door inside handle.
    Text in Illustration 
    *1
    Rear Door Inside Locking Cable Assembly
    *2
    Rear Door Lock Remote Control Cable Assembly



    B307182
  1. Engage the 7 clips.



    B308235
  1. Engage the clip.



    B307134
  1. Install the rear door trim board sub-assembly with the 3 screws.



    B307179
  1. Engage the claw and close the cover.



9. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
  1. Connect the connector.



    B307129
  1. Engage the 3 guides and 8 claws to install the rear power window regulator switch assembly with rear door armrest base panel.



10. INSTALL REAR DOOR FRAME GARNISH


    B307128
  1. Engage the guide.

  1. Engage the 2 clips and 3 claws to install the rear door frame garnish.



11. CONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



12. INSTALL FRONT FLOOR COVER RH
  1. Engage the 3 guides.



    B301488E01
  1. Engage the clip <B> to install the front floor cover RH.

  1. Install the 2 clips <A>.



13. INITIALIZE POWER WINDOW CONTROL SYSTEM
(Click here)


14. INSPECT POWER WINDOW OPERATION
(Click here)